scholarly journals Lattice Reinforced Cermet Materials

2021 ◽  
Author(s):  
A Pascall
Keyword(s):  
Cermet Materials

OPTICAL PROPERTIES OF CERMET MATERIALS

1981 ◽  
Vol 42 (C1) ◽  
pp. C1-247-C1-284 ◽  
Author(s):  
C. G. Granqvist
Keyword(s):  
Optical Properties ◽  
Cermet Materials

A new method of preparing Ni/YSZ cermet materials

2011 ◽  
Vol 47 (6) ◽  
pp. 2807-2817 ◽  
Author(s):  
E. Drożdż-Cieśla ◽  
J. Wyrwa ◽  
W. Pyda ◽  
M. Rękas
Keyword(s):  
New Method ◽  
Cermet Materials

Effect of Raw Materials on Properties of Coated Al2O3-Al Cermet Materials via Vacuum Sintering Method

2020 ◽  
Vol 858 ◽  
pp. 53-58
Author(s):  
Ai Xia Chen ◽  
Chao Yang ◽  
Rui Hua Wang ◽  
Fang Wang ◽  
Ming Han Xu ◽  
...  
Keyword(s):  
Ball Milling ◽  
Raw Materials ◽  
Surface Hardness ◽  
Chemical Precipitation ◽  
Chemical Precipitation Method ◽  
Precipitation Method ◽  
Cermet Material ◽  
Milling Method ◽  
Cermet Materials ◽  
Mechanical Ball Milling

In this paper, the effect of raw materaisl on the properties of coated Al2O3/Al cermet materials were investigated, the raw materials were prepared via different methods, which provide a reference for obtaining higher performance cermet materials. Through mixing, molding, sintering, sample preparation, scanning electron microscopic observation, energy spectrometer observation and analysis, the following conclusions can be drawn, the density of the cermet material prepared by the mechanical ball milling method (83.5%) is higher than that of the cermet material prepared by the chemical precipitation method (92.8%). It is nearly 10% lower. The alumina particles prepared by the ball milling method are agglomerated, and a large amount of agglomeration occurs in the aluminum, and the composition is very uneven. For materials prepared by the precipitation method, the aluminum oxide is uniformly distributed in the aluminum. The ball-milling powder is used to prepare materials, most of the alumina is in the form of particles, and in the precipitation method. In the powder preparation sample, the thin layer of alumina which forms the same eggshell envelops the aluminum, and the aluminum has a certain liquid phase change. the surface hardness (824HV) of the cermet material prepared by the mechanical ball milling method is lower than the surface hardness (1005HV) of the cermet material prepared by the chemical precipitation method.

scholarly journals Particle Erosion and Microstructure of Fe-Cr-C Cermet Materials Prepared by Mechanical Alloying (MA).

2000 ◽  
Vol 47 (5) ◽  
pp. 515-520
Author(s):  
Kazuhiro Hasezaki ◽  
Noriyuki Hayashi ◽  
Masatomo Kamada ◽  
Setsuo Takaki
Keyword(s):  
Mechanical Alloying ◽  
Particle Erosion ◽  
Cermet Materials

scholarly journals Preparation and characterization of coal gangue/Al cermet materials

2021 ◽  
Vol 290 ◽  
pp. 01016
Author(s):  
Guihua Wu ◽  
Lihua Tang
Keyword(s):  
Compression Strength ◽  
Mass Fraction ◽  
Coal Gangue ◽  
Static Compression ◽  
Cermet Material ◽  
Mass Fractions ◽  
Al Powder ◽  
Main Components ◽  
Cermet Materials

In this study, the calcined coal gangue was mixed with Al powder at different mass fractions (5wt%〜35wt%). After being pressed at 80MPa and sintered at 1200°C for 2h, the coal gangue/Al cermet material was obtained. The phase composition, microstructure and mechanical properties of the material were studied. The results show that the main components of the prepared materials are Al, mullite, AlN, alumina and silicon. With the increase of coal gangue powder, the hardness of coal gangue/Al cermet gradually increases, while the static compression strength first increases and then decreases. When the mass fraction of gangue is 25wt%, the coal gangue/Al cermet material has the best performance. Density is 2.23g/cm3, hardness is 752HV, static compression strength is 127.3MPa.

Sign in / Sign up

Export Citation Format

Share Document