OPTICAL PROPERTIES OF CERMET MATERIALS

1981 ◽  
Vol 42 (C1) ◽  
pp. C1-247-C1-284 ◽  
Author(s):  
C. G. Granqvist
Keyword(s):  
Optical Properties ◽  
Cermet Materials

Copper Cermets used as Selective Coatings for Flat Plate Solar Collectors

2008 ◽  
Vol 59 (6) ◽  
Author(s):  
Mihaela Voinea ◽  
Cristina Bogatu ◽  
Gabrielle Charlotte Chitanu ◽  
Anca Duta
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Copper Acetate ◽  
Point Of View ◽  
Solar Collectors ◽  
Ir Spectrometry ◽  
Acetate Methyl ◽  
Spray Pyrolysis Deposition ◽  
Ft Ir ◽  
Cermet Materials

The aim of the present work is to offer a practical mode to obtain thin films of Cu/CuOx cermets by two different methods: electrodeposition and spray pyrolysis deposition (SPD). The cooper precursor in both cases was copper acetate. The films morphology for the SPD samples was optimized by adding copolymers of maleic anhydride with controlled hydrophobia (vinyl acetate/methyl methacrylate) in the precursor�s solution. The samples were characterized from the point of view of: topography (AFM/STM), composition (XRD, using CuKa1), and optical properties (UV-VIS and FT-IR spectrometry). These cermet materials are extensively studied due to their applications as selective coatings for solar collectors.

Design of objective lens for 200-kV high-resolution electron microscopes

1983 ◽  
Vol 41 ◽  
pp. 314-315
Author(s):  
K. Tsuno ◽  
T. Honda ◽  
Y. Harada ◽  
M. Naruse
Keyword(s):  
Optical Properties ◽  
Computer Technology ◽  
Axial Magnetic Field ◽  
Chromatic Aberration ◽  
Objective Lens ◽  
Resolution Electron ◽  
Correction Of Astigmatism ◽  
Three Stages ◽  
Electron Microscopes ◽  
Stage 1

Developement of computer technology provides much improvements on electron microscopy, such as simulation of images, reconstruction of images and automatic controll of microscopes (auto-focussing and auto-correction of astigmatism) and design of electron microscope lenses by using a finite element method (FEM). In this investigation, procedures for simulating the optical properties of objective lenses of HREM and the characteristics of the new lens for HREM at 200 kV are described.The process for designing the objective lens is divided into three stages. Stage 1 is the process for estimating the optical properties of the lens. Firstly, calculation by FEM is made for simulating the axial magnetic field distributions Bzc of the lens. Secondly, electron ray trajectory is numerically calculated by using Bzc. And lastly, using Bzc and ray trajectory, spherical and chromatic aberration coefficients Cs and Cc are numerically calculated. Above calculations are repeated by changing the shape of lens until! to find an optimum aberration coefficients.

Optical Properties of HVEM Accelerators

1975 ◽  
Vol 33 ◽  
pp. 180-181
Author(s):  
A. Strojnik ◽  
J.W. Scholl ◽  
V. Bevc
Keyword(s):  
Optical Properties ◽  
Electron Accelerator ◽  
Systematic Investigation ◽  
Electron Source ◽  
High Brightness ◽  
The Past ◽  
Wide Range ◽  
Optical Behavior

The electron accelerator, as inserted between the electron source (injector) and the imaging column of the HVEM, is usually a strong lens and should be optimized in order to ensure high brightness over a wide range of accelerating voltages and illuminating conditions. This is especially true in the case of the STEM where the brightness directly determines the highest resolution attainable. In the past, the optical behavior of accelerators was usually determined for a particular configuration. During the development of the accelerator for the Arizona 1 MEV STEM, systematic investigation was made of the major optical properties for a variety of electrode configurations, number of stages N, accelerating voltages, 1 and 10 MEV, and a range of injection voltages ϕ0 = 1, 3, 10, 30, 100, 300 kV).

Differential polarization imaging of sickled cells

1988 ◽  
Vol 46 ◽  
pp. 62-63
Author(s):  
Marcos F. Maestre
Keyword(s):  
Optical Properties ◽  
Theoretical Approach ◽  
Polarized Light ◽  
Polarization Microscopy ◽  
Spectroscopic Techniques ◽  
Polarization Imaging ◽  
Circularly Polarized Light ◽  
Circularly Polarized ◽  
Microscopic Scale ◽  
Chiral Structures

Recently we have developed a form of polarization microscopy that forms images using optical properties that have previously been limited to macroscopic samples. This has given us a new window into the distribution of structure on a microscopic scale. We have coined the name differential polarization microscopy to identify the images obtained that are due to certain polarization dependent effects. Differential polarization microscopy has its origins in various spectroscopic techniques that have been used to study longer range structures in solution as well as solids. The differential scattering of circularly polarized light has been shown to be dependent on the long range chiral order, both theoretically and experimentally. The same theoretical approach was used to show that images due to differential scattering of circularly polarized light will give images dependent on chiral structures. With large helices (greater than the wavelength of light) the pitch and radius of the helix could be measured directly from these images.

A transmission electron microscopic study of structural transitions in fast ionic conductors

1987 ◽  
Vol 45 ◽  
pp. 156-157
Author(s):  
R. B. Queenan ◽  
P. K. Davies
Keyword(s):  
Optical Properties ◽  
Ionic Conduction ◽  
Recent Observation ◽  
Ionic Conductivities ◽  
Sodium Aluminate ◽  
Two Dimensions ◽  
Ionic Conductors ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Trivalent Cations

Na ß“-alumina (Na1.67Mg67Al10.33O17) is a non-stoichiometric sodium aluminate which exhibits fast ionic conduction of the Na+ ions in two dimensions. The Na+ ions can be exchanged with a variety of mono-, di-, and trivalent cations. The resulting exchanged materials also show high ionic conductivities.Considerable interest in the Na+-Nd3+-ß“-aluminas has been generated as a result of the recent observation of lasing in the pulsed and cw modes. A recent TEM investigation on a 100% exchanged Nd ß“-alumina sample found evidence for the intergrowth of two different structure types. Microdiffraction revealed an ordered phase coexisting with an apparently disordered phase, in which the cations are completely randomized in two dimensions. If an order-disorder transition is present then the cooling rates would be expected to affect the microstructures of these materials which may in turn affect the optical properties. The purpose of this work was to investigate the affect of thermal treatments upon the micro-structural and optical properties of these materials.

Practical Correction of Three Fold Astigmatism in the Philips CM TEM

1996 ◽  
Vol 54 ◽  
pp. 418-419
Author(s):  
Arno J. Bleeker ◽  
Mark H.F. Overwijk ◽  
Max T. Otten
Keyword(s):  
Optical Properties ◽  
Phase Contrast ◽  
The Other ◽  
Objective Lens ◽  
Symmetric Part ◽  
A Posteriori ◽  
Contrast Transfer Function ◽  
High Brightness ◽  
Rotationally Symmetric ◽  
Brightness Field

With the improvement of the optical properties of the modern TEM objective lenses the point resolution is pushed beyond 0.2 nm. The objective lens of the CM300 UltraTwin combines a Cs of 0. 65 mm with a Cc of 1.4 mm. At 300 kV this results in a point resolution of 0.17 nm. Together with a high-brightness field-emission gun with an energy spread of 0.8 eV the information limit is pushed down to 0.1 nm. The rotationally symmetric part of the phase contrast transfer function (pctf), whose first zero at Scherzer focus determines the point resolution, is mainly determined by the Cs and defocus. Apart from the rotationally symmetric part there is also the non-rotationally symmetric part of the pctf. Here the main contributors are not only two-fold astigmatism and beam tilt but also three-fold astigmatism. The two-fold astigmatism together with the beam tilt can be corrected in a straight-forward way using the coma-free alignment and the objective stigmator. However, this only works well when the coefficient of three-fold astigmatism is negligible compared to the other aberration coefficients. Unfortunately this is not generally the case with the modern high-resolution objective lenses. Measurements done at a CM300 SuperTwin FEG showed a three fold-astigmatism of 1100 nm which is consistent with measurements done by others. A three-fold astigmatism of 1000 nm already sinificantly influences the image at a spatial frequency corresponding to 0.2 nm which is even above the point resolution of the objective lens. In principle it is possible to correct for the three-fold astigmatism a posteriori when through-focus series are taken or when off-axis holography is employed. This is, however not possible for single images. The only possibility is then to correct for the three-fold astigmatism in the microscope by the addition of a hexapole corrector near the objective lens.

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

1980 ◽  
Vol 38 ◽  
pp. 266-269
Author(s):  
Y. Harada ◽  
K. Tsuno ◽  
Y. Arai
Keyword(s):  
Optical Properties ◽  
High Resolution ◽  
Chromatic Aberration ◽  
Point Of View ◽  
Pole Piece ◽  
Axial Field ◽  
Design Considerations ◽  
Resolution Electron ◽  
Practical Design ◽  
Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

Sign in / Sign up

Export Citation Format

Share Document