scholarly journals A Bayesian inversion framework for yield and height-of-burst/depth-of-burial for near-surface explosions

2015 ◽  
Author(s):  
Gardar Johannesson ◽  
Vera Bulaevskaya ◽  
Abe Ramirez ◽  
Sean Ford ◽  
Artie Rodgers
Keyword(s):  
Bayesian Inversion ◽  
Near Surface ◽  
Depth Of Burial

MAPPING EARTH CONDUCTIVITIES USING A MULTIFREQUENCY AIRBORNE ELECTROMAGNETIC SYSTEM

Geophysics ◽  
1978 ◽  
Vol 43 (3) ◽  
pp. 563-575 ◽  
Author(s):  
H. O. Seigel ◽  
D. H. Pitcher
Keyword(s):  
Thin Sheet ◽  
Radar Altimeter ◽  
Electromagnetic System ◽  
Near Surface ◽  
Quantitative Estimates ◽  
Simple Geometry ◽  
Airborne Electromagnetic ◽  
Groundwater Mapping ◽  
Actual Field ◽  
Depth Of Burial

The Tridem vertical coplanar airborne electromagnetic system provides simultaneous in‐phase and quadrature information at frequencies of 500, 2000 and 8000 Hz. The system can map a broad range of earth conductors of simple geometry and provide quantitative estimates of their conductivities and dimensions. Computer programs have been developed to automatically interpret the six channels of Tridem data, plus the output of an accurate radar altimeter, to determine the depth of burial, conductivity and thickness of a near‐surface, flat‐lying conducting horizon. In limiting cases, the interpretation provides the conductance (conductivity‐thickness product) of a thin sheet (ranging from 100 mmhos to 100 mhos) or the conductivity of a homogeneous earth (ranging from 1 mmhos/m to 10 mhos/m). Two actual field examples are presented from Ontario, Canada; one relating to the mapping of overburden conditions (sand, clay and rock, etc) and the other to the mapping of the distribution of a buried lignite deposit. Other areas of potential application of the system to surficial materials would include groundwater mapping, permafrost investigations, and civil engineering studies for roads and pipelines.

scholarly journals Experimental and Numerical Investigation of the Ground Shock Coupling Factor for Near-Surface Detonations

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Timothy W. Shelton ◽  
John Q. Ehrgott ◽  
Ramon J. Moral ◽  
Michele Barbato
Keyword(s):  
Numerical Simulations ◽  
Coupling Factor ◽  
Shock Propagation ◽  
Buried Structures ◽  
Near Surface ◽  
Ground Shock ◽  
Particle Velocities ◽  
Development Center ◽  
Depth Of Burial ◽  
Physical Quantities

This paper presents the results of recent ground shock experiments conducted by the U.S. Army Engineer Research and Development Center to further investigate the adequacy of the coupling factor approach to shallow-buried or near-surface detonations. Comparisons between these recent experimental results and results of numerical simulations of the ground shock propagation in soil are presented. It was found that the coupling factor curve currently adopted in design of buried structures does not accurately represent the actual ground shock propagation in soil and that different coupling factor curves are needed for different physical quantities of interest in design. The results presented in this paper also suggest that the coupling factor curves are functions of several parameters in addition to the depth of burial and that numerical simulations can capture reasonably well the ground shock propagation of soil stresses and particle velocities.

scholarly journals Partitioning of Seismoacoustic Energy and Estimation of Yield and Height-of-Burst/Depth-of-Burial for Near-Surface Explosions

2014 ◽  
Vol 104 (2) ◽  
pp. 608-623 ◽  
Author(s):  
S. R. Ford ◽  
A. J. Rodgers ◽  
H. Xu ◽  
D. C. Templeton ◽  
P. Harben ◽  
...  
Keyword(s):  
Near Surface ◽  
Depth Of Burial

Aquifer heterogeneity from SH‐wave seismic impedance inversion

Geophysics ◽  
2002 ◽  
Vol 67 (5) ◽  
pp. 1548-1557 ◽  
Author(s):  
Kevin D. Jarvis ◽  
Rosemary J. Knight
Keyword(s):  
Shallow Aquifer ◽  
Velocity Variation ◽  
Bayesian Inversion ◽  
Cone Penetrometer ◽  
Seismic Velocities ◽  
Sh Wave ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
The Impact

We collected SH‐wave seismic reflection data over a shallow aquifer in southwestern British Columbia to investigate the use of such data in hydrogeologic applications. We used this data set in developing a methodology that uses cone penetrometer data as an integral part of the inversion and interpretation of the seismic data. A Bayesian inversion technique converts the seismic amplitude variations to velocity variations, honoring the probabilities of the priors and adhering to a geologically reasonable sparseness criterion. Velocity measurements acquired with the cone penetrometer provide velocity profiles and vertical seismic profiling (VSP) data, all of which are valuable in properly constraining the Bayesian inversion. The differentiation of lithologies (in this data set, sand and clay) is accomplished by first using a normalization procedure to remove the impact of effective stress, which dominates the velocity variation in the upper 10 to 20 m. The final transformation of seismic velocities to void ratio for the sand‐dominated regions is made using laboratory‐derived measurements; it provides an image of the heterogeneity of the near‐surface aquifer.

Benthic foraminiferal zonation in deep-water carbonate platform margin environments, northern Little Bahama Bank

1988 ◽  
Vol 62 (01) ◽  
pp. 1-8 ◽  
Author(s):  
Ronald E. Martin
Keyword(s):  
Deep Water ◽  
Benthic Foraminifera ◽  
Carbonate Platform ◽  
Sedimentary Facies ◽  
Depositional Environments ◽  
Near Surface ◽  
Sediment Gravity Flows ◽  
Gravity Flows ◽  
Platform Margin ◽  
Water Carbonate

The utility of benthic foraminifera in bathymetric interpretation of clastic depositional environments is well established. In contrast, bathymetric distribution of benthic foraminifera in deep-water carbonate environments has been largely neglected. Approximately 260 species and morphotypes of benthic foraminifera were identified from 12 piston core tops and grab samples collected along two traverses 25 km apart across the northern windward margin of Little Bahama Bank at depths of 275-1,135 m. Certain species and operational taxonomic groups of benthic foraminifera correspond to major near-surface sedimentary facies of the windward margin of Little Bahama Bank and serve as reliable depth indicators. Globocassidulina subglobosa, Cibicides rugosus, and Cibicides wuellerstorfi are all reliable depth indicators, being most abundant at depths >1,000 m, and are found in lower slope periplatform aprons, which are primarily comprised of sediment gravity flows. Reef-dwelling peneroplids and soritids (suborder Miliolina) and rotaliines (suborder Rotaliina) are most abundant at depths <300 m, reflecting downslope bottom transport in proximity to bank-margin reefs. Small miliolines, rosalinids, and discorbids are abundant in periplatform ooze at depths <300 m and are winnowed from the carbonate platform. Increased variation in assemblage diversity below 900 m reflects mixing of shallow- and deep-water species by sediment gravity flows.

Analysis of 2D and 3D defects associated with precipitation of Cu in silicon

1991 ◽  
Vol 49 ◽  
pp. 870-871
Author(s):  
P.M. Rice ◽  
MJ. Kim ◽  
R.W. Carpenter
Keyword(s):  
Colony Growth ◽  
Dark Field ◽  
Dark Side ◽  
Silicide Phase ◽  
Strain Fields ◽  
Near Surface ◽  
Unknown Composition ◽  
Secondary Precipitates ◽  
20 Nm ◽  
2D And 3D

Extrinsic gettering of Cu on near-surface dislocations in Si has been the topic of recent investigation. It was shown that the Cu precipitated hetergeneously on dislocations as Cu silicide along with voids, and also with a secondary planar precipitate of unknown composition. Here we report the results of investigations of the sense of the strain fields about the large (~100 nm) silicide precipitates, and further analysis of the small (~10-20 nm) planar precipitates.Numerous dark field images were analyzed in accordance with Ashby and Brown's criteria for determining the sense of the strain fields about precipitates. While the situation is complicated by the presence of dislocations and secondary precipitates, micrographs like those shown in Fig. 1(a) and 1(b) tend to show anomalously wide strain fields with the dark side on the side of negative g, indicating the strain fields about the silicide precipitates are vacancy in nature. This is in conflict with information reported on the η'' phase (the Cu silicide phase presumed to precipitate within the bulk) whose interstitial strain field is considered responsible for the interstitial Si atoms which cause the bounding dislocation to expand during star colony growth.

Shock consolidation of Ni-Ti alloy powder

1986 ◽  
Vol 44 ◽  
pp. 430-431
Author(s):  
Naresh N. Thadhani ◽  
Thad Vreeland ◽  
Thomas J. Ahrens
Keyword(s):  
Alloy Powder ◽  
Amorphous Material ◽  
Ti Alloy ◽  
Two Phase ◽  
Near Surface ◽  
Optical Micrograph ◽  
Shock Compaction ◽  
Powder Particles ◽  
Ti Powder ◽  
Rapidly Solidified

A spherically-shaped, microcrystalline Ni-Ti alloy powder having fairly nonhomogeneous particle size distribution and chemical composition was consolidated with shock input energy of 316 kJ/kg. In the process of consolidation, shock energy is preferentially input at particle surfaces, resulting in melting of near-surface material and interparticle welding. The Ni-Ti powder particles were 2-60 μm in diameter (Fig. 1). About 30-40% of the powder particles were Ni-65wt% and balance were Ni-45wt%Ti (estimated by EMPA).Upon shock compaction, the two phase Ni-Ti powder particles were bonded together by the interparticle melt which rapidly solidified, usually to amorphous material. Fig. 2 is an optical micrograph (in plane of shock) of the consolidated Ni-Ti alloy powder, showing the particles with different etching contrast.

Preparation of cross-sectional samples for near-surface TEM studies

1987 ◽  
Vol 45 ◽  
pp. 380-381
Author(s):  
R.C. Dickenson ◽  
K.R. Lawless
Keyword(s):  
Standard Sample ◽  
Surface Region ◽  
Specimen Preparation ◽  
Thick Sheet ◽  
Drill Bit ◽  
Sample Holder ◽  
Metal Interface ◽  
Cross Sectional ◽  
Near Surface ◽  
Cold Worked

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.

Near-Surface Aggregation of Sn In Heavily Sn-Doped GaAs Films Grown By Molecular Beam Epitaxy

1985 ◽  
Vol 43 ◽  
pp. 368-369
Author(s):  
S. H. Chen
Keyword(s):  
Molecular Beam Epitaxy ◽  
Cross Section ◽  
Electron Spectroscopy ◽  
Molecular Beam ◽  
Surface Segregation ◽  
Secondary Ion Mass Spectrometry ◽  
Specimen Preparation ◽  
Near Surface ◽  
Gaas Films ◽  
Secondary Ion

Sn has been used extensively as an n-type dopant in GaAs grown by molecular-beam epitaxy (MBE). The surface accumulation of Sn during the growth of Sn-doped GaAs has been observed by several investigators. It is still not clear whether the accumulation of Sn is a kinetically hindered process, as proposed first by Wood and Joyce, or surface segregation due to thermodynamic factors. The proposed donor-incorporation mechanisms were based on experimental results from such techniques as secondary ion mass spectrometry, Auger electron spectroscopy, and C-V measurements. In the present study, electron microscopy was used in combination with cross-section specimen preparation. The information on the morphology and microstructure of the surface accumulation can be obtained in a fine scale and may confirm several suggestions from indirect experimental evidence in the previous studies.

Specimen Preparation of Near Surface Ion Irradiated Samples

1985 ◽  
Vol 43 ◽  
pp. 170-171
Author(s):  
K. F. Russell ◽  
L. L. Horton
Keyword(s):  
Radiation Damage ◽  
Heavy Ions ◽  
Target Material ◽  
Metal Alloys ◽  
Specimen Surface ◽  
Specimen Preparation ◽  
Particle Accelerators ◽  
Near Surface ◽  
Graaff Accelerator ◽  
Van De Graaff

Beams of heavy ions from particle accelerators are used to produce radiation damage in metal alloys. The damaged layer extends several microns below the surface of the specimen with the maximum damage and depth dependent upon the energy of the ions, type of ions, and target material. Using 4 MeV heavy ions from a Van de Graaff accelerator causes peak damage approximately 1 μm below the specimen surface. To study this area, it is necessary to remove a thickness of approximately 1 μm of damaged metal from the surface (referred to as “sectioning“) and to electropolish this region to electron transparency from the unirradiated surface (referred to as “backthinning“). We have developed electropolishing techniques to obtain electron transparent regions at any depth below the surface of a standard TEM disk. These techniques may be applied wherever TEM information is needed at a specific subsurface position.

Sign in / Sign up

Export Citation Format

Share Document