scholarly journals BLT-EC (Breach, Leach Transport, and Equilibrium Chemistry), a finite-element model for assessing the release of radionuclides from low-level waste disposal units: Background, theory, and model description

1995 ◽  
Author(s):  
R.J. MacKinnon ◽  
T.M. Sullivan ◽  
S.A. Simonson ◽  
C.J. Suen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Waste Disposal ◽  
Element Model ◽  
Model Description ◽  
Low Level ◽  
Background Theory ◽  
Theory And Model

Contact Stress and Linearized Modal Predictions of As-Built Preloaded Assembly

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Adam R. Brink ◽  
Robert J. Kuether ◽  
Matthew D. Fronk ◽  
Bryan L. Witt ◽  
Brendan L. Nation
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Contact Area ◽  
Element Model ◽  
High Fidelity ◽  
Vibration Modes ◽  
Low Level ◽  
Pressure Sensitive ◽  
Sensitive Film ◽  
Pressure Sensitive Film

Abstract The member stiffness and pressure distribution in a bolted joint is significantly influenced by the contact area of the mechanical interface under a prescribed preload force. This research explores the influence of as-built surface profiles for nominally flat interfaces of a C-Beam assembly with two well-defined contact regions. A high-fidelity finite element model is created such that the model uncertainty is minimized by updating and calibrating the piece parts prior to the preload assembly procedure. The model is then assembled and preloaded to evaluate the contact stresses and contact area for both nominally flat and perturbed non-flat surfaces based on three-dimensional surface topography measurements. The predicted pressures are validated with digitized pressure-sensitive film measurements. The high-fidelity modeling reveals how the compliance and thickness of the pressure-sensitive film alter the measured pressures, leading to incorrect evaluations of the stresses and contact area in the joint. The resulting low-level dynamic behavior of the preloaded assembly is shown to be sensitive to the true contact area by linearizing the nonlinear finite element model about the preloaded equilibrium and performing a computational modal analysis. The resonant frequencies are validated with experimental measurements to demonstrate the effect of the contact area on the modal characteristics of the bolted assembly. Vibration modes and loading patterns exhibit varying levels of sensitivity to the contact area in the joint, leading to an improved physical understanding of the influence of contact mechanics on the low-level linear vibration modes of jointed assemblies.

Predicting Radionuclide Release Rates from Spent Nuclear Fuel Inside a Failed Waste Disposal Container Using a Finite Element Model

CORROSION ◽  
10.5006/2866 ◽  
2018 ◽  
Vol 75 (3) ◽  
pp. 302-308 ◽  
Author(s):  
Nazhen Liu ◽  
Ziyan Zhu ◽  
Linda Wu ◽  
Zack Qin ◽  
James J. Noël ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Nuclear Fuel ◽  
Waste Disposal ◽  
Spent Nuclear Fuel ◽  
Element Model ◽  
Release Rates ◽  
Radionuclide Release

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Sign in / Sign up

Export Citation Format

Share Document