scholarly journals Removal of methylene blue from aqueous solution using Mg-Fe, Zn-Fe, Mn-Fe layered double hydroxide

2020 ◽  
Vol 81 (12) ◽  
pp. 2522-2532
Author(s):  
Zhongliang Shi ◽  
Yanmei Wang ◽  
Shuyu Sun ◽  
Cheng Zhang ◽  
Haibo Wang
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Langmuir Adsorption ◽  
Molar Ratios ◽  
Pseudo Second Order ◽  
Co Precipitation ◽  
Double Hydroxide ◽  
Double Hydroxides

Abstract Layered double hydroxides (LDH) with highly flexible and adjustable chemical composition and physical properties have attracted tremendous attention in recent years. A series of LDH with different M (Mg, Zn, Mn)-Fe molar ratios were synthesized by the double titration co-precipitation method. The effect of the factors, including M (Mg, Zn, Mn) : Fe molar ratio, pH, and M-Fe LDH dosage, on the ability of the prepared M-Fe LDH to remove cationic methylene blue (MB) dye from aqueous solution were investigated. Results indicated that the removal efficiency of MB (10 mg/L) was the best at the M (Mg, Zn, Mn): Fe molar ratio of 3:1 by using 2.0 g/L of M-Fe LDH at pH 6.0 under 298.15 K. Mg-Fe LDH had the highest removal performance (71.94 mg/g at 298.15 K) for MB compared to those of the Zn-Fe and Mn-Fe LDH. Zn-Fe LDH with the smallest activation energy resulted in the fastest adsorption rate of MB. The pseudo-second-order model and Langmuir adsorption isotherm were also successfully applied to fit the theory of M-Fe LDH for removal of MB.

scholarly journals Removal of Lead from Aqueous Solution by Adsorption using Magnesium Aluminium Hydrogenphosphate Layered Double Hydroxides

2014 ◽  
Vol 8 (1) ◽  
Author(s):  
Zaini Hamzah ◽  
Mohd Najif Ab Rahman ◽  
Yamin Yasin ◽  
Siti Mariam Sumari ◽  
Ahmad Saat
Keyword(s):  
Aqueous Solution ◽  
Layered Double Hydroxide ◽  
Molar Ratio ◽  
Maximum Adsorption Capacity ◽  
Lead Removal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Precipitation ◽  
Double Hydroxide ◽  
Double Hydroxides

Layered double hydroxide with molar ratio of 4 (MAN 4) was synthesized by co-precipitation and followed by hydrothermal method. The compound was then later going through ion exchange with K2HPO4 for 48 hours to produce MgAlHPO4 (MAHP 4). The solid produced were characterized using X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FTIR). Adsorption of lead solution by MAHP 4 was carried out using batch experiment by mixing the lead solution and the solid of layered double hydroxide. The effects of various parameters such as contact time, pH, adsorbent dosage and initial concentration were investigated. The optimum pH for lead removal was found to be at pH of 5 and the optimum time of lead removal was found at 2 hours. The isotherm data was analysed using Langmuir and the correlation coefficient of 0.998 was obtained. The maximum adsorption capacity, Qo (mg/g) of 500 mg/g was also recorded from the Langmuir isotherm. The remaining lead solution was determined by using EDXRF (Energy Dispersive X-Ray Fluorescence spectrometry) model MiniPal 4 (PAN analytical). The results in this study indicate that MAHP 4 was an interesting adsorbent for removing lead from aqueous solution.

scholarly journals FABRICATION OF Mg-Zn-Al HYDROTALCITE AND ITS APPLICATION FOR Pb2+ REMOVAL

2019 ◽  
Vol 59 (3) ◽  
pp. 260-271 ◽  
Author(s):  
Eddy Heraldy ◽  
Fitria Rahmawati ◽  
Dwi Ardiyanti ◽  
Ika Nurmawanti
Keyword(s):  
Second Order ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Adsorption Efficiency ◽  
Molar Ratios ◽  
Isotherm Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Co Precipitation ◽  
Kinetics Of

The fabrication of Mg-Zn-Al Hydrotalcite (HT) was carried out by the co-precipitation method at various molar ratios. The Mg-Zn-Al HT compound at the optimum molar ratio was then calcined to determine the effect of calcination on the Pb2+ adsorption. The kinetics of the adsorption type was determined by applying pseudo first order and pseudo second order kinetics models. Meanwhile, to investigate the adsorption process, the Freundlich and Langmuir equations were applied to determine the adsorption isotherm. The results showed that the optimum Mg-Zn-Al HT was at a molar ratio of 3 : 1 : 1 with an adsorption efficiency of 73.16 %, while Mg-Zn-Al HT oxide increased the adsorption efficiency to 98.12 %. The optimum condition of Pb2+ removal using Mg-Zn-Al HT oxide was reached at pH 5 and a contact time of 30 minutes. The adsorption kinetics follows the pseudo second order kinetics model with a rate constant of 0.544 g/mg·min. The isotherm adsorption follows the Langmuir isotherm model with a maximum capacity of 3.916 mg/g and adsorption energy of 28.756 kJ/mol.

scholarly journals Gas-Phase Hydrogenation of Furfural to Furfuryl Alcohol over Cu-ZnO-Al2O3 Catalysts Prepared from Layered Double Hydroxides

Catalysts ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 486
Author(s):  
Guillermo R. Bertolini ◽  
Carmen P. Jiménez-Gómez ◽  
Juan Antonio Cecilia ◽  
Pedro Maireles-Torres
Keyword(s):  
Gas Phase ◽  
Aging Time ◽  
Layered Double Hydroxides ◽  
Furfuryl Alcohol ◽  
Precipitation Method ◽  
Molar Ratio ◽  
X Ray ◽  
General Chemical ◽  
Co Precipitation ◽  
Double Hydroxides

Several layered double hydroxides (LDHs) with general chemical composition (Cu,Zn)1−xAlx(OH)2(CO3)x/2·mH2O have been synthesized by the co-precipitation method, maintaining a (M2+/M3+) molar ratio of 3, and varying the Cu2+/Zn2+ molar ratio between 0.2 and 6.0. After calcination and reduction steps, Cu/ZnO/Al2O3 catalysts were synthesized. These catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), H2 thermoprogrammed reduction (H2-TPR), N2 adsorption-desorption at −196 °C, N2O titration, X-ray photoelectron miscroscopy (XPS), NH3-thermoprogramed desorption (NH3-TPD) and CO2- thermoprogrammed desorption (CO2-TPD). The characterization data revealed that these catalysts are mainly meso-and macroporous, where Cu, ZnO and Al2O3 are well dispersed. The catalytic results show that these catalysts are active in the gas-phase hydrogenation of furfural, being highly selective to furfuryl alcohol (FOL) and reaching the highest FOL yield for the catalyst with a Cu2+/Zn2+ molar ratio of 1. In an additional study, the influence of the aging time on the synthesis of the LDHs was also evaluated. The catalytic data revealed that the use of shorter aging time in the formation of the LDH has a beneficial effect on the catalytic behavior, since more disordered structures with a higher amount of available Cu sites is obtained, leading to a higher yield towards FOL (71% after 5 h of time-on-stream at 210 °C).

Effect of Doped Iron on Fluoride Sorption by Calcined MgAlFe-CO3 Layered Double Hydroxides

2013 ◽  
Vol 681 ◽  
pp. 21-25
Author(s):  
Yu Bing Pu ◽  
Jia Rui Wang ◽  
Hong Zheng ◽  
Peng Cai ◽  
Si Yuan Wu
Keyword(s):  
Layered Double Hydroxides ◽  
Synthetic Wastewater ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Fluoride Removal ◽  
Maximum Sorption Capacity ◽  
Fluoride Adsorption ◽  
Maximum Sorption ◽  
Co Precipitation ◽  
Double Hydroxides

A series of MgAlFe-CO3 layered double hydroxides (LDHs) were successfully prepared by co-precipitation method. With synthetic wastewater, the effect of doped iron on fluoride sorption by calcined MgAlFe-CO3 layered double hydroxides (CLDH) under different pH and contact time conditions was investigated. The sorption isotherm data were fitted well to Langmuir isotherm at 25 °C. The maximum sorption capacity of fluoride on CLDH increases first and then decreases with the increase of Fe/Al molar ratio and attains maximum of 71.94 mg/g when Fe/Al molar ratio is 1:2, although doped iron is unfavorable to the regeneration of original layered structure for CLDH after fluoride adsorption. No aluminium in the solution after fluoride adsorption was detected when Fe/Al molar ratio is equal to or larger than 1:2. The results indicate that CLDH with proper Fe/Al molar ratio is a promising candidate as an adsorbent material for fluoride removal from aqueous solutions.

Chlorate Removal by Calcined Mg/Fe/Ce Layered Double Hydroxides

2015 ◽  
Vol 737 ◽  
pp. 537-540
Author(s):  
Yan Wei Guo ◽  
Hua Zhang ◽  
Zhi Liang Zhu
Keyword(s):  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Langmuir Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Kinetics Of

A novel Mg/Fe/Ce layered double hydroxide (LDHs) and its calcined product (CLDH) were synthesized and CLDH was used as adsorbents for the removal of chlorate ions. Results showed that the initial solution pH was an important factor influencing the chlorate adsorption. The adsorption behavior of chlorate followed the Langmuir adsorption isotherm with a maximum adsorption capacity of 18.2 mg/g. The adsorption kinetics of chlorate on CLDH can be described by the pseudo-second-order kinetic model. It was concluded that the CLDH material is a potential adsorbent for the purification of polluted water with chlorate.

scholarly journals Structural Stability of Ni/Al Layered Double Hydroxide Supported on Graphite and Biochar Toward Adorption of Congo Red

2021 ◽  
Vol 6 (2) ◽  
pp. 85-95
Author(s):  
Patimah Mega Syah Bahar Nur Siregar ◽  
Neza Rahayu Palapa ◽  
Alfan Wijaya ◽  
Erni Salasia Fitri ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Layered Double Hydroxide ◽  
Congo Red ◽  
High Performance ◽  
Precipitation Method ◽  
First Order ◽  
Xrd Diffraction ◽  
Co Precipitation ◽  
Double Hydroxide

In this research, Ni/Al layered double hydroxide (LDH) was modified by using co-precipitation method to generate Ni/Al-graphite (Ni/Al-GF) and Ni/Al-biochar (Ni/Al-BC). The adsorbents were applied to remove Congo Red from aqueous solution. The obtained samples were characterized by using XRD, FTIR, BET and TG-DTA. The XRD diffraction pattern of Ni/Al LDH, Ni/Al-GF, and Ni/Al-BC presented the formation of composite with decreasing crystallinity. The surface area modified LDHs was higher than the pristine materials, which was obtained 15.106 m2/g, 21.595 m2/g and 438.942 m2/g for Ni/Al-LDH, Ni/Al-GF, Ni/Al-BC respectively. The adsorption of Congo Red on the materials was tested at diferent parameters and the results exhibited that Congo Red adsorption on LDHs were pseudo-first-order (PFO) kinetic, spontaneous, endothermic and followed Langmuir model. The adsorbents removed Congo Red by high performance stability with adsorption capacity was 116.297 mg/g for Ni/Al-GF and 312.500 mg/g for Ni/Al-BC. These adsorption capacity was higher than the pristine LDH (61.728 mg/g). The regeneration process which carried out for five cycles showed that Ni/Al-GF and Ni/Al-BC have stable structures as reuse adsorbents for Congo Red from aqueous solution.

scholarly journals Adsorptive Capacity of Malachite Green onto Mg/M3+ (M3+=Al and Cr) LDHs

2021 ◽  
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
High Stability ◽  
Adsorption Process ◽  
Adsorptive Capacity ◽  
Xrd Pattern ◽  
Langmuir Adsorption ◽  
Stability Structure ◽  
Pseudo Second Order ◽  
Double Hydroxides

<p>Layered double hydroxides (LDHs) of MgM3+ (M3+=Al and Cr) were synthesized by coprecipitation method to form Mg/Al and Mg/Cr LDHs. The materials were applied as adsorbents of malachite green in aqueous solution. The physical properties of Mg/Al and Mg/Cr were analyzed using XRD, FTIR, BET and TGDTA characterizations. The XRD pattern shows the characteristic of LDHs which has diffraction at 11.470 (003) and at 34.690 (012) for Mg/Al and 12.450 (003) and at 380 (012) for Mg/Cr. The interlayer spaces of Mg/Al and Mg/Cr LDHs were 7.71 Å and 7.62 Å, respectively. The surface area of Mg/Al was higher than Mg/Cr. The FTIR spectra confirm that the intense peak at 1385 cm-1 denotes vibration of nitrate bond and M-O band in under 1000 cm-1. Thus the Mg/Al and Mg/Cr LDHs were applied as adsorbents to remove malachite green in aqueous solution. The results of malachite green adsorption showed that malachite green was adsorbed onto Mg/Al and Mg/Cr followed pseudo second order and Langmuir adsorption parameter. The adsorption capacity of malachite green for Mg/Al and Mg/Cr was 44.444 mg/g and 33.784 mg/g, respectively. The thermodynamic study showed that the adsorption process was spontaneous, endothermic and favored in high temperature. The regeneration process showed that Mg/Al and Mg/Cr LDHs has high stability structure toward reusability of adsorbent until three cycles adsorption process.</p>

scholarly journals Malachite Green Removal by Zn/Al-citrate LDHs in Aqueous Solution

2020 ◽  
Vol 5 (2) ◽  
pp. 59
Author(s):  
Nurlisa Hidayati ◽  
Risfidian Mohadi ◽  
Elfita Elfita ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
Adsorption Process ◽  
Langmuir Adsorption Isotherm ◽  
Precipitation Method ◽  
Chemical Adsorption ◽  
Langmuir Adsorption ◽  
Batch System ◽  
Isotherm Adsorption ◽  
Co Precipitation

Zn/Al-citrate LDHs was synthesized using co precipitation method at basic condition and the material were applied as adsorbent of malachite green (MG) dye in aqueous medium using batch system. Adsorption of MG onto Zn/Al-citrate was investigated through kinetic, isotherm adsorption and thermodynamic studies. Kinetic model was fitted PSO than PFO for MG adsorption. The rate of adsorption 𝑘2 for Zn/Al LDHs was 0.000692 g.mg−1 min−1 and 0.000371 g for Zn/Al-citrate LDHs.mg−1 min−1. Adsorption of malachite green onto Zn/Al LDHs and Zn/Al citrate LDHs was investigated and following Langmuir adsorption isotherm model shows chemical adsorption process. The adsorption capacity maximum of Zn/Al-citrate is 333 mg/g from Zn/Al LDHs is only 111 mg/g. Thermodynamic parameters of Zn/Al-citrate confirmed adsorption process was endothermic and spontaneous.

Inorganic layered double hydroxides as a 4-hexyl resorcinol delivery system for topical applications

RSC Advances ◽  
2016 ◽  
Vol 6 (81) ◽  
pp. 77709-77716 ◽  
Author(s):  
Damodar Mosangi ◽  
Sreejarani Kesavan Pillai ◽  
Lumbidzani Moyo ◽  
Suprakas Sinha Ray
Keyword(s):  
Controlled Release ◽  
Layered Double Hydroxide ◽  
Delivery System ◽  
Layered Double Hydroxides ◽  
Skin Tone ◽  
Precipitation Method ◽  
Co Precipitation ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Topical Applications

In this study, the hydrophobic even skin tone active, 4-hexylresorcinol is intercalated into a Zn–Al layered double hydroxide by co-precipitation method and used as controlled release ingredient in a skin care formulation.

scholarly journals Efficient decolorization of Methylene Blue catalyzed by MgFe-layered double hydroxides in the presence of hydrogen peroxide

2020 ◽  
Vol 81 (4) ◽  
pp. 781-789
Author(s):  
Qian Wang ◽  
Xiaofei Wang ◽  
Siqian Liu ◽  
Rong Li
Keyword(s):  
Methylene Blue ◽  
Hydroxyl Radicals ◽  
Layered Double Hydroxides ◽  
Room Temperature ◽  
Heterogeneous Catalysts ◽  
Precipitation Method ◽  
Fenton Process ◽  
Initial Ph ◽  
Co Precipitation ◽  
Double Hydroxides

Abstract MgFe-layered double hydroxides (LDHs) were prepared by co-precipitation method with the ratios of [Mg2+]/[Fe3+] varied in the range of 2:1–6:1, and occupied as heterogeneous catalysts for the degradation of Methylene Blue (MB) in the Fenton process. MgFe-LDH prepared with the ratio of [Mg2+]/[Fe3+] at 3:1 was verified to be of high purity. The Fenton-like process catalyzed by MgFe-LDH performed excellently, and more than 97% degradation of MB was obtained with 0.5 mmol/L H2O2 and 0.50 g/L MgFe-LDH at initial pH 2 at room temperature. The occurrence of hydroxyl radicals (·OH) was detected and the mechanism was proposed. MgFe-LDH is of excellent catalytic activity and good reusability.

Sign in / Sign up

Export Citation Format

Share Document