Effect of solution chemistry and operating conditions on the nanofiltration of acid dyes by a nanocomposite membrane

2011 ◽  
Vol 64 (12) ◽  
pp. 2404-2409 ◽  
Author(s):  
A. Akbari ◽  
M. Homayoonfal ◽  
V. Jabbari
Keyword(s):  
Uv Irradiation ◽  
Separation Efficiency ◽  
Irradiation Time ◽  
Membrane Surface ◽  
Operating Conditions ◽  
Solution Chemistry ◽  
Polymerization Process ◽  
Inversion Method ◽  
Sem Images ◽  
Polysulfone Membrane

A composite nanofiltration membrane was developed by a poly(acrylic acid) in situ ultraviolet (UV) graft polymerization process using an ultrafiltration polysulfone membrane as a porous support, by a phase inversion method. SEM images showed that the PSf membranes had numerous finger-like pores. Atomic force microscopy (AFM) showed that the roughness of the surface was reduced by an increase in UV irradiation times. The rejections of sodium chloride and sodium sulfate were moderate and declined with the increase of concentration. We observed that by increasing UV irradiation time and nanofiltration pressure applied, retention of dyes was enhanced and in the most irradiated membrane (M-4 membrane) at 4 bars, color removal with a high rejection of about 99.80% was achieved. It was found that the separation efficiency of dyes in the mixture of salt and dyes decreased with the salt concentration due to a decrease in the Donnan effect. It was also found that by varying the pH, the membrane surface and the dyes' charges are changed, which meant that the membrane surface and dyes had different interactions at various pHs.

Surface Modification of Asymmetric Polysulfone Membrane by UV Irradiation

2014 ◽  
Vol 70 (2) ◽  
Author(s):  
Sutthisa Konruang ◽  
Thawat Chittrakarn ◽  
Suksawat Sirijarukul
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Functional Groups ◽  
Uv Irradiation ◽  
Water Flux ◽  
Inversion Method ◽  
Asymmetric Structure ◽  
Polysulfone Membrane ◽  
Polar Functional Groups ◽  
Polysulfone Membranes

The effects of ultraviolet (UV) irradiation for surface modification of hydrophobic asymmetric polysulfone membranes have been investigated. The asymmetric polysulfone (PSF) membranes were prepared by phase inversion method using 19%-25% of PSF in two solvents, viz. dimethylacetamide (DMF) and Acetone (Ac) collectively. The surface of asymmetric polysulfone membranes were modified by UV ray with 254 and 312 nm wavelength. Chemical and physical properties of the untreated and the treated membranes were characterized. Scanning electron microscope (SEM) was used to determine asymmetric structure of polysulfone membranes. Contact angle device was used to analyzed the effected of UV ray treatment on hydrophilicity of membranes surface. Polar functional groups introduced by UV irradiation were examined using FTIR. The water flux was measured under a pressure of 500 kPa to 2,500 kPa with a feed temperature of 25°C. It was shown that asymmetric polysulfone membranes were produced and the UV ray treatment significantly alters the hydrophilicity of membranes surface indicated by the reduction of water contact angle with increasing treatment time. The FTIR analysis showed the formations of polar functional groups such as hydroxyl and carbonyl groups. Consequently, the surface of asymmetric polysulfone membranes was changed from hydrophobic to hydrophilic by UV irradiation leading to the enhancement of the water flux.

scholarly journals Fabrication and Characterization of GO-Fe3O4/PSF Membrane with Phase Inversion Method

2021 ◽  
Vol 6 (2) ◽  
pp. 55-60
Author(s):  
Vivia Maulida Alfianti ◽  
◽  
Munasir Munasir ◽  
Keyword(s):  
Phase Inversion ◽  
Average Pore Size ◽  
Membrane Surface ◽  
Xrd Analysis ◽  
Solid Matrix ◽  
Coagulation Bath ◽  
Inversion Method ◽  
Average Pore ◽  
Polysulfone Membrane ◽  
Phase Inversion Method

Polysulfones are hydrophobic which can reduce membrane permeability. Permeability can be increased through the application of hydrophilic materials such as GO-Fe3O4 to the polysulfone membrane so that the membrane is hydrophilic. The riset purpose to determine the effect of the percentage weight of different material compositions on the hydrophilicity properties of the polysulfone membrane. Membrane fabrication is carried out using the phase inversion method where the polymer solution is molded in a place and immersed in a coagulation bath containing non-solvent. This solvent exchange causes the polymer to form a solid matrix and become a membrane. The results showed that GO particles were successfully doped with Fe3O4 material shown by XRD analysis at a peak of 35.61˚ with a magnetite phase, while FTIR analysis showed that there was an absorption band characteristic of Fe-O streching vibrations. The results of the contact angle test on the GO-Fe3O4/PSF membrane 0.75 wt per cent were around 73.17˚ which showed the smallest hydrophobic value and the membrane surface morphology had an average pore size of 333.61 nm so that the addition of GO-Fe3O4 composites could increase membrane hydrophilicity.

scholarly journals Investigation of surface and filtration properties of TiO2 coated ultrafiltration polyacrylonitrile membranes

2017 ◽  
Vol 77 (4) ◽  
pp. 931-938 ◽  
Author(s):  
I. Kovács ◽  
G. Veréb ◽  
Sz. Kertész ◽  
S. Beszédes ◽  
C. Hodúr ◽  
...  
Keyword(s):  
Uv Irradiation ◽  
Irradiation Time ◽  
Membrane Surface ◽  
Oxygen Demand ◽  
Limiting Factors ◽  
Cleaning Process ◽  
Cake Layer ◽  
Coated Membranes ◽  
Wastewater Filtration ◽  
Filtration Properties

Abstract In the present work, the surface and filtration properties of TiO2 coated polyacrylonitrile ultrafiltration membranes were investigated. The membranes were coated using the physical deposition method. The appropriate TiO2 coverage proved to be 0.3 mg/cm2, which formed a hydrophilic cake layer on the membrane surface. The cleanability without chemicals and the retention of the coated membranes was compared to the neat membrane after model oily wastewater filtration. The cleaning sustained of rinsing with distilled water and ultraviolet (UV) irradiation of the fouled membranes. The coated membranes have better antifouling properties; higher flux values during oily water filtration and by the mentioned cleaning process a significantly better flux recovery can be achieved. The amount of the catalyst and the irradiation time are limiting factors to the effectiveness of the cleaning process. The UV irradiation increases the wettability of the fouled membrane surface by degrading the oil layer. The coating, the continuous use, and the cleaning process do not significantly affect the membrane retention expressed in chemical oxygen demand.

scholarly journals Fouling Removal of UF Membrane with Coated TiO2Nanoparticles under UV Irradiation for Effluent Recovery during TFT-LCD Manufacturing

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
S. H. You ◽  
C. T. Wu
Keyword(s):  
Uv Irradiation ◽  
Membrane Fouling ◽  
Liquid Crystal Display ◽  
Membrane Surface ◽  
Thin Film Transistor ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Secondary Effluent ◽  
Operating Pressure ◽  
Permeate Flux

An ultrafiltration (UF) membrane process was employed to treat the secondary effluent discharged from a manufacturing of thin film transistor-liquid crystal display (TFT-LCD) in this study. A bench-scale system was performed to evaluate the fouling removal of a UF membrane with coated titanium dioxide (TiO2) nanoparticles under UV irradiation. The operating pressure and feed temperature were controlled at 300 KN/m2and 25°C, respectively. It was found that the optimum operating conditions were attained with TiO2concentrations of 10 wt% for both 5 KD and 10 KD MWCO. Continuous UV irradiation of 5 KD MWCO improved the permeate flux rate from 45.0% to 59.5% after 4 hours of operation. SEM-EDS analysis also showed that the photocatalytic effect had reduced the average thickness of cake fouling on the membrane from 6.40 μm to 2.70 μm for 5 KD MWCO and from 6.70 μm to 3.1 μm for 10 KD MWCO. In addition, the membrane contact angle was reduced from 54° to 44°. The photocatalytic properties of TiO2apparently increased the hydrophilicity of the membrane surface, thereby reducing membrane fouling.

"Recent Patents on the Triboelectrostatic Separation of Fly Ash"

2019 ◽  
Vol 13 ◽  
Author(s):  
Haisheng Li ◽  
Wenping Wang ◽  
Yinghua Chen ◽  
Xinxi Zhang ◽  
Chaoyong Li
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
High Efficiency ◽  
Separation Efficiency ◽  
High Reliability ◽  
Operating Conditions ◽  
Security Requirements ◽  
Unburned Carbon ◽  
Efficient Operation ◽  
Triboelectrostatic Separation

Background: The fly ash produced by coal-fired power plants is an industrial waste. The environmental pollution problems caused by fly ash have been widely of public environmental concern. As a waste of recoverable resources, it can be used in the field of building materials, agricultural fertilizers, environmental materials, new materials, etc. Unburned carbon content in fly ash has an influence on the performance of resource reuse products. Therefore, it is the key to remove unburned carbon from fly ash. As a physical method, triboelectrostatic separation technology has been widely used because of obvious advantages, such as high-efficiency, simple process, high reliability, without water resources consumption and secondary pollution. Objective: The related patents of fly ash triboelectrostatic separation had been reviewed. The structural characteristics and working principle of these patents are analyzed in detail. The results can provide some meaningful references for the improvement of separation efficiency and optimal design. Methods: Based on the comparative analysis for the latest patents related to fly ash triboelectrostatic separation, the future development is presented. Results: The patents focused on the charging efficiency and separation efficiency. Studies show that remarkable improvements have been achieved for the fly ash triboelectrostatic separation. Some patents have been used in industrial production. Conclusion: According to the current technology status, the researches related to process optimization and anti-interference ability will be beneficial to overcome the influence of operating conditions and complex environment, and meet system security requirements. The intelligent control can not only ensure the process continuity and stability, but also realize the efficient operation and management automatically. Meanwhile, the researchers should pay more attention to the resource utilization of fly ash processed by triboelectrostatic separation.

scholarly journals Tanning Wastewater Treatment by Ultrafiltration: Process Efficiency and Fouling Behavior

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 461
Author(s):  
Fu Yang ◽  
Zhengkun Huang ◽  
Jun Huang ◽  
Chongde Wu ◽  
Rongqing Zhou ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Shear Rate ◽  
Membrane Surface ◽  
Filtration Efficiency ◽  
Operating Conditions ◽  
Process Efficiency ◽  
Transmembrane Pressure ◽  
Leather Industry ◽  
Pore Blocking ◽  
The Impact

Ultrafiltration is a promising, environment-friendly alternative to the current physicochemical-based tannery wastewater treatment. In this work, ultrafiltration was employed to treat the tanning wastewater as an upstream process of the Zero Liquid Discharge (ZLD) system in the leather industry. The filtration efficiency and fouling behaviors were analyzed to assess the impact of membrane material and operating conditions (shear rate on the membrane surface and transmembrane pressure). The models of resistance-in-series, fouling propensity, and pore blocking were used to provide a comprehensive analysis of such a process. The results show that the process efficiency is strongly dependent on the operating conditions, while the membranes of either PES or PVDF showed similar filtration performance and fouling behavior. Reversible resistance was the main obstacle for such process. Cake formation was the main pore blocking mechanism during such process, which was independent on the operating conditions and membrane materials. The increase in shear rate significantly increased the steady-state permeation flux, thus, the filtration efficiency was improved, which resulted from both the reduction in reversible resistance and the slow-down of fouling layer accumulate rate. This is the first time that the fouling behaviors of tanning wastewater ultrafiltration were comprehensively evaluated, thus providing crucial guidance for further scientific investigation and industrial application.

Enhanced Photocatalytic Performance of Sn6SiO8 Nanoparticles and Their Reduced Graphene Oxide (rGO) Nanocomposite

2020 ◽  
Vol 20 (9) ◽  
pp. 5426-5432
Author(s):  
G. Gnanamoorthy ◽  
M. Muthukumaran ◽  
P. Varun Prasath ◽  
V. Karthikeyan ◽  
V. Narayanan ◽  
...  
Keyword(s):  
Visible Light ◽  
Photocatalytic Performance ◽  
Separation Efficiency ◽  
Dye Degradation ◽  
Hexagonal Phase ◽  
Active Species ◽  
Organic Chemical ◽  
Light Illumination ◽  
Sem Images ◽  
Radical Trapping

Photocatalysts provide excellent potential for the full removal of organic chemical pollutants as an environmentally friendly technology. It has been noted that under UV-visible light irradiation, nanostructured semiconductor metal oxides photocatalysts can degrade different organic pollutants. The Sn6SiO8/rGO nanocomposite was synthesized by a hydrothermal method. The Sn6SiO8 nanoparticles hexagonal phase was confirmed by XRD and functional groups were analyzed by FT-IR spectroscopy. The bandgap of Sn6SiO8 nanoparticles (NPs) and Sn6SiO8/GO composites were found to be 2.7 eV and 2.5 eV, respectively. SEM images of samples showed that the flakes like morphology. This Sn6SiO8/rGO nanocomposite was testing for photocatalytic dye degradation of MG under visible light illumination and excellent response for the catalysts. The enhancement of photocatalytic performance was mainly attributed to the increased light absorption, charge separation efficiency and specific surface area, proved by UV-vis DRS. Further, the radical trapping experiments revealed that holes (h+) and superoxide radicals (·O−2) were the main active species for the degradation of MG, and a possible photocatalytic mechanism was discussed.

scholarly journals Green Synthesis and Characterization of Pullulan Mediated Silver Nanoparticles through Ultraviolet Irradiation

Materials ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2382 ◽  
Author(s):  
Muhammad Jamshed Khan ◽  
Suriya Kumari ◽  
Kamyar Shameli ◽  
Jinap Selamat ◽  
Awis Qurni Sazili
Keyword(s):  
Silver Nanoparticles ◽  
Uv Irradiation ◽  
Irradiation Time ◽  
Edible Films ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Selected Area Electron Diffraction ◽  
Vis Spectroscopy ◽  
Face Centered ◽  
Average Lattice

Nanoparticles (NPs) are, frequently, being utilized in multi-dimensional enterprises. Silver nanoparticles (AgNPs) have attracted researchers in the last decade due to their exceptional efficacy at very low volume and stability at higher temperatures. Due to certain limitations of the chemical method of synthesis, AgNPs can be obtained by physical methods including sun rays, microwaves and ultraviolet (UV) radiation. In the current study, the synthesis of pullulan mediated silver nanoparticles (P-AgNPs) was achieved through ultraviolet (UV) irradiation, with a wavelength of 365 nm, for 96 h. P-AgNPs were formed after 24 h of UV-irradiation time and expressed spectra maxima as 415 nm, after 96 h, in UV-vis spectroscopy. The crystallographic structure was “face centered cubic (fcc)” as confirmed by powder X-ray diffraction (PXRD). Furthermore, high resolution transmission electron microscopy (HRTEM) proved that P-AgNPs were covered with a thin layer of pullulan, with a mean crystalline size of 6.02 ± 2.37. The average lattice fringe spacing of nanoparticles was confirmed as 0.235 nm with quasi-spherical characteristics, by selected area electron diffraction (SAED) analysis. These green synthesized P-AgNPs can be utilized efficiently, as an active food and meat preservative, when incorporated into the edible films.

Optimization of biodiesel synthesis under simultaneous ultrasound-microwave irradiation using response surface methodology (RSM)

2015 ◽  
Vol 4 (4) ◽  
Author(s):  
Seyed Mohammad Safieddin Ardebili ◽  
Teymor Tavakoli Hashjin ◽  
Barat Ghobadian ◽  
Gholamhasan Najafi ◽  
Stefano Mantegna ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Microwave Irradiation ◽  
Response Surface ◽  
Palm Oil ◽  
Catalyst Concentration ◽  
Irradiation Time ◽  
Operating Conditions ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Biodiesel Synthesis

AbstractThis work investigates the effect of simultaneous ultrasound-microwave irradiation on palm oil transesterification and uncovers optimal operating conditions. Response surface methodology (RSM) has been used to analyze the influence of reaction conditions, including methanol/palm oil molar ratio, catalyst concentration, reaction temperature and irradiation time on biodiesel yield. RSM analyses indicate 136 s and 129 s as the optimal sonication and microwave irradiation times, respectively. Optimized parameters for full conversion (97.53%) are 1.09% catalyst concentration and a 7:3.1 methanol/oil molar ratio at 58.4°C. Simultaneous ultrasound-microwave irradiation dramatically accelerates the palm oil transesterification reaction. Pure biodiesel was obtained after only 2.2 min while the conventional method requires about 1 h.

CFD Investigation of Downhole Natural Gas Separation Efficiency in the Churn Flow Regime

2021 ◽  
Author(s):  
Charles Okafor ◽  
Patrick Verdin ◽  
Phill Hart
Keyword(s):  
Natural Gas ◽  
Flow Regime ◽  
Gas Separation ◽  
Separation Efficiency ◽  
Operating Conditions ◽  
Analytical Models ◽  
Design Stage ◽  
Average Error ◽  
Multiphase Model ◽  
Churn Flow

Abstract Downhole Natural Gas Separation Efficiency (NGSE) is flow regime dependent, and current analytical models in certain conditions lack accuracy. Downhole NGSE was investigated through 3D Computational Fluid Dynamics (CFD) transient simulations for pumping wells in the Churn flow regime. The Volume of Fluid (VOF) multiphase model was considered along with the k – ε turbulence model for most simulations. A mesh independence study was performed, and the final model results validated against experimental data, showing an average error of less than 6 %. Numerical simulation results showed that the steady state assumption used by current mathematical models for churn flow can be inaccurate. Several key parameters affecting the NGSE were identified, and suggestions for key improvements to the widely used mathematical formulations for viscous flow provided. Sensitivity studies were conducted on fluid/geometric parameters and operating conditions, to gain a better understanding of the influence of each parameter on NGSE. These are important results as they equip the ESP engineer with additional knowledge to maximise the NGSE from design stage to pumping operations.

Sign in / Sign up

Export Citation Format

Share Document