A pilot scale study of a sequencing batch reactor treating municipal wastewater operated via the UP-PND process

2008 ◽  
Vol 58 (2) ◽  
pp. 435-438 ◽  
Author(s):  
M. Kornaros ◽  
C. Marazioti ◽  
G. Lyberatos
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Treatment Plant ◽  
Pilot Scale ◽  
Treated Wastewater ◽  
Synthetic Wastewater ◽  
Second Step ◽  
Decentralized Wastewater Treatment ◽  
Real Wastewater

SBRs are usually preferred as small and decentralized wastewater treatment systems. We have demonstrated previously that using a frequent enough switching between aerobic and anoxic conditions and a specific to the treated wastewater aerobic to anoxic phase ratio, it is possible to by-pass the second step of nitrification (i.e. conversion of nitrite to nitrate nitrogen). This innovative process for nitrate by-pass has been branded as UP-PND (University of Patras-Partial Nitrification Denitrification) (WO 2006/129132). The proved methodology was successfully transferred from a lab-scale SBR reactor treating synthetic wastewater to a pilot-scale SBR system treating real wastewater. In this work we present the results from the operation of this pilot-scale SBR, constructed in the Wastewater Treatment Plant of Patras (Greece), using 6-hour, 8-hour and 12-hour cycles. It is demonstrated that three pairs of aerobic/anoxic phases with a relative duration of 1:2 (8-hour cycle) and 2:3 (12-hour cycle) secures the desired by-pass of nitrate production.

scholarly journals Suitability of SBR for Wastewater Treatment and Reuse: Pilot-Scale Reactor Operated in Different Anoxic Conditions

2020 ◽  
Vol 17 (5) ◽  
pp. 1617 ◽  
Author(s):  
Omar Alagha ◽  
Ahmed Allazem ◽  
Alaadin A. Bukhari ◽  
Ismail Anil ◽  
Nuhu Dalhat Mu'azu
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Quality Parameters ◽  
Wastewater Management ◽  
Wastewater Quality

The present study investigates the performance of a pilot-scale Sequencing Batch Reactor (SBR) process for the treatment of wastewater quality parameters, including turbidity, total suspended solids (TSS), total solids (TS), nitrogen (ammonia (NH3–N), nitrite (NO2−), and nitrate (NO3−), phosphate (PO43−), the chemical oxygen demand (COD), and the 5-day biological oxygen demand (BOD5), from municipal wastewater. Two scenarios, namely, pre-anoxic denitrification and post-anoxic denitrification, were investigated to examine the performance of a pilot-scale SBR on the wastewater quality parameters, particularly the nitrogen removal. The correlation statistic was applied to explain the effects of operational parameters on the performance of the SBR system. The results revealed that the post-anoxic denitrification scenario was more efficient for higher qualify effluent than the first scenario. The effluent concentrations of the targeted wastewater quality parameters obtained for the proposed SBR system were below those of the local standards, while its performance was better than that of the North Sewage Treatment Plant, Dharan, Eastern province, Kingdom of Saudi Arabia (KSA), in terms of the BOD5, COD, TN, and PO43- treatment efficiencies. These results indicated the suitability of SBR technology for wastewater treatment in remote areas in the KSA, with a high potential of reusability for sustainable wastewater management.

scholarly journals Efficiency of municipal wastewater treatment with membrane bioreactor

2019 ◽  
Vol 41 (1) ◽  
pp. 47-54
Author(s):  
Magdalena Domańska ◽  
Anna Boral ◽  
Kamila Hamal ◽  
Magdalena Kuśnierz ◽  
Janusz Łomotowski ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Membrane Filtration ◽  
Municipal Wastewater ◽  
High Efficiency ◽  
Biological Membrane ◽  
Treatment Plant ◽  
Membrane Reactors ◽  
Quality Analysis ◽  
Treated Wastewater ◽  
Municipal Wastewater Treatment

AbstractThe increasingly stringent requirements for wastewater treatment enforce the adoption of technologies that reduce pollution and minimize waste production. By combining the typical activated sludge process with membrane filtration, biological membrane reactors (MBR) offer great technological potential in this respect. The paper presents the principles and effectiveness of using an MBR at the Głogów Małopolski operation. Physicochemical tests of raw and treated wastewater as well as microscopic analyses with the use of the FISH (fluorescence in situ hybridization) method were carried out. Moreover, the level of electric energy consumption during the operation of the wastewater treatment plant and problems related to fouling were also discussed. A wastewater quality analysis confirmed the high efficiency of removing organic impurities (on average 96% in case of BOD5 and 94% in case of COD) and suspension (on average 93%).

Efficient treatment of dairy processing wastewater in a laboratory scale Intermittently Aerated Sequencing Batch Reactor (IASBR)

2018 ◽  
Vol 85 (3) ◽  
pp. 379-383 ◽  
Author(s):  
Peter Leonard ◽  
Emma Tarpey ◽  
William Finnegan ◽  
Xinmin Zhan
Keyword(s):  
Wastewater Treatment ◽  
Retention Time ◽  
Wastewater Treatment Plant ◽  
Sequencing Batch Reactor ◽  
Batch Reactor ◽  
Treatment Plant ◽  
Laboratory Scale ◽  
Synthetic Wastewater ◽  
Operational Parameters ◽  
Dairy Processing

This Research Communication describes an investigation into the viability of an Intermittently Aerated Sequencing Batch Reactor (IASBR) for the treatment of dairy processing wastewater at laboratory-scale. A number of operational parameters have been varied and the effect has been monitored in order to determine optimal conditions for maximising removal efficiencies. These operational parameters include Hydraulic Retention Time (HRT), Solids Retention Time (SRT), aeration rate and cycle length. Real dairy processing wastewater and synthetic wastewater have been treated using three laboratory-scale IASBR units in a temperature controlled room. When the operational conditions were established, the units were seeded using sludge from a municipal wastewater treatment plant for the first experiment, and sludge from a dairy processing factory for the second and third experiment. In experiment three, the reactors were fed on real wastewater from the wastewater treatment plant at this dairy processing factory. These laboratory-scale systems will be used to demonstrate over time that the IASBR system is a consistent, viable option for treatment of dairy processing wastewater in this sector. In this study, the capacity of a biological system to remove both nitrogen and phosphorus within one reactor will be demonstrated. The initial operational parameters for a pilot-scale IASBR system will be derived from the results of the study.

Operation and Optimization of an Alternating Oxic-Anoxic Shortcut Nitrification-Denitrification System

2014 ◽  
Vol 1030-1032 ◽  
pp. 387-390
Author(s):  
Chun Di Gao ◽  
Shi Xin Fan ◽  
Er Long Jiao ◽  
Hao Li ◽  
Wei Xiao Wang
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Operation Mode ◽  
Treatment Plant ◽  
Domestic Wastewater ◽  
Optimization Approach ◽  
Municipal Wastewater Treatment ◽  
Operational Parameters ◽  
Pollutant Discharge

A novel alternating oxic-anoxic operation mode of shortcut nitrification-denitrification was developed in a sequencing batch reactor at ambient temperature. Operational parameters favorable for maintaining the shortcut nitrification-denitrification were investigated and optimized. The experiments showed that alternating oxic-anoxic shortcut nitrification-denitrification system was able to be an independent treatment process in domestic wastewater treatment. And the optimization approach was so efficient that the main pollutant discharge targets achieved Standard A of the first class in "Discharge standard of pollutants for municipal wastewater treatment plant". Moreover, the reliability of the operation strategy in this experimentation was proved, which indicated the excellent nitrogen removal performances.

Biological treatment of industrial wastes in a photobioreactor

2006 ◽  
Vol 53 (11) ◽  
pp. 117-125 ◽  
Author(s):  
E. Tamer ◽  
M.A. Amin ◽  
E.T. Ossama ◽  
M. Bo ◽  
G. Benoit
Keyword(s):  
Wastewater Treatment ◽  
Biological Treatment ◽  
Treatment Plant ◽  
Algal Growth ◽  
Bacterial Consortium ◽  
Industrial Wastes ◽  
Synthetic Wastewater ◽  
Phenol Removal ◽  
The Real ◽  
Real Wastewater

An algal-bacterial consortium was tested for the treatment from a coke factory. A Chlorella vulgaris strain and a phenol-degrading Alcaligenes sp. were first isolated from the wastewater treatment plant to serve as inocula in the subsequent biodegradation tests. Batch tests were then conducted with samples from the real wastewater or using a synthetic wastewater containing 325 mg phenol/l and 500 mg NH4+/l as target pollutants. Direct biological treatment of the real wastewater was not possible due to the toxicity of organic compounds. Activated carbon adsorption and UV(A-B)-irradiation were efficient in detoxifying the effluent for subsequent biological treatment as inoculation of pretreated samples with the algal-bacterial consortium was followed by complete phenol removal and NH4+ removal of 45%. Complete phenol removal and 33% NH4+ removal were achieved during the fed-batch treatment of artificial wastewater at 6 d hydraulic retention time (HRT). Under continuous feeding at 3.6 d HRT, phenol and NH4+ removal dropped to 58 and 18%, respectively. However, complete phenol removal and 29% NH4+ removal were achieved when 8 g NaHCO3/l was added to the artificial wastewater to enhance algal growth. This study confirms the potential of solar-based industrial wastewater treatment based on solar-based UV pretreatment followed by algal-bacterial biodegradation.

scholarly journals Removal of organics and metal ion nanoparticles from synthetic wastewater by activated sludge process (ASP)

2014 ◽  
Author(s):  
Tarunveer Singh ◽  
Shubhanshu Jain
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Metal Ions ◽  
Organic Contaminants ◽  
Metal Ion ◽  
Treatment Plant ◽  
Poor Quality ◽  
Treated Wastewater ◽  
Synthetic Wastewater ◽  
Batch Reactors

Adsorption technique is widely used for removal of toxic organic contaminants from aqueous streams. Owing to the hazardous or otherwise undesirable characteristics of phenolic compounds in particular, their presence in wastewater from municipal and industrial discharge is one of the most important environmental issue. The discharge of poor quality effluents by the chemical-based laboratories and refineries in India is posing a serious threat to water sources and wastewater treatment installations alike. Our study was set up in the Indo - French Unit for Water & Wastewater Technologies (IFUWWT), IIT Delhi. The main objective of this study was to assess the efficiency of a laboratory-scale activated sludge treatment process in producing a final effluent conforming to regulatory standards of Central Pollution Control Board, India (CPCB norms) with regards to COD and metal ion loads. The study was conducted in three principal stages: characterization of wastewater containing nanoparticles; treatability studies of laboratory generated discards and investigations of heavy metal ions before and after treatment. The various raw effluent parameters analyzed were COD, BOD, F/M ratio, Sludge Value Index, Total Solids and concentrations of Cu, Ag and Zn. Studies were conducted using two aerobic sequencing batch reactors (SBR). MLSS of the aeration basin was calculated to be 7180±261.3 mg/L while the F/M ratio was kept down to 0.1560±.0149; besides, an SVI of 107.24 mL/g complied with the state of bioreactor’s sludge. These set of values suggested to set an extended aeration processes for the reactors. Accordingly, the detention time in aeration basin was 24 hours. The results showed over 98% influent COD reduction and nearly 100% removal of metal ions. The sample used was operated on sludge collected from Vasant Kunj Wastewater Treatment plant. Based on the results from waste characterization and treatability studies, it was decided that the mixed liquor discharged in the activation tank should have glucose solution and laboratory discarded sample in 1:1 ratio. The reactor was operated on a glucose fed batch basis for 30 days. For the sake of metal analysis, the digested water samples were analyzed for the presence of copper, silver and zinc using the ElementAS AAS4141 Atomic Absorption Spectrophotometer (by Electronics Corporation of India Ltd). The biosorption capacities were found to be over 95% in all the cases with the minimum correlation coefficient for calibration curve being 0.9811. Such a high sludge yield is suggestive of the fact that heavy metals are in very low concentrations in the considered carboy sample. Because of these insignificant values, the amount of metal ions introduced to the system gets adsorbed almost completely, hence leaving behind no metal ion within the supernatant. Well-treated wastewater has enormous potential as a source of water for crops, households and industry.

scholarly journals Microcoagulation improved the performance of the UF–RO system treating the effluent from a coastal municipal wastewater treatment plant: a pilot-scale study

2021 ◽  
Author(s):  
Tong Yu ◽  
Chenlu Xu ◽  
Feng Chen ◽  
Haoshuai Yin ◽  
Hao Sun ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Wastewater Treatment Plant ◽  
Membrane Fouling ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Pilot Scale ◽  
Contaminant Removal ◽  
Municipal Wastewater Treatment ◽  
Municipal Wastewater Treatment Plant ◽  
Ro Membrane

Abstract Microcoagulation has recently been considered as a promising pretreatment for an ultrafiltration (UF) process from numerous studies. To investigate the effects of microcoagulation on the performance of the UF–reverse osmosis (RO) system treating wastewater with high and fluctuant salinity, different dosages of coagulant (poly-aluminum chloride) were added prior to the UF unit in a pilot-scale UF–RO system for a 10-week period operation. Microcoagulation obviously improved the contaminant removal and cleaning efficiencies, including water backwash, chemical enhanced backwash and cleaning in place processes. Organic fouling was dominated during the initial stage of the RO membrane fouling. The microbial communities of water samples and foulant on the RO membrane were similar to those of seawater and foulant on the RO membranes from seawater RO plants. The microbial community of the foulant on the membrane was similar to that of UF permeate and RO concentrate. These results demonstrated that microcoagulation could improve the performance of the UF–RO system treating the effluent with high and fluctuant salinity from a coastal municipal wastewater treatment plant.

scholarly journals Coke oven wastewater treatment by two activated sludge systems

2013 ◽  
Vol 8 (1) ◽  
pp. 16-22
Keyword(s):  
Organic Matter ◽  
Wastewater Treatment ◽  
Activated Sludge ◽  
Nutrient Removal ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Coke Oven ◽  
Synthetic Wastewater ◽  
Removal Efficiencies ◽  
Activated Sludge Systems

In this study two bench scale activated sludge systems were used, a CSTR and an SBR for the treatment of coke – oven wastewater. Both reactors were inoculated with activated sludge from a municipal wastewater treatment plant. At the first stages of operation, reactors were feed by a mixture of municipal wastewater and synthetic wastewater. Full acclimatization of the microorganisms to synthetic wastewater was achieved in 60 days. The operation of the reactors was divided into three distinct periods. The first period was characterized by the treatment of high organic but non-toxic synthetic wastewater. During this period COD and BOD5 removal efficiencies reached 95 and 98% respectively, in both reactors. Nutrient removal was better in the SBR reactor rather than in the CSTR. In the second period phenol was added in concentrations up to 300 mg l-1. Degradation of phenol started about the 20th day after its introduction to the reactors. In this period no effects of phenol to nutrient removal were observed, whereas the removal efficiency of organic matter in both reactors was slightly decreased. During the third period phenol concentrations of the influent were gradually increased to 1000 mg l-1, while cyanide and thiocyanite were added to the influent composition to concentrations reaching concentrations of 20 and 250 mg l-1 respectively. The composition of the influent of this period was a full assimilation of coke oven wastewater. Introduction of increased phenol concentrations along with cyanide compounds initiated irreversible effects on the activated sludge microfauna of the CSTR causing inherent problems to the treatment process, while SBR showed greater capacity to withstand and degrade toxic compounds. The beginning of this period was characterized by decreased settleability of the suspended solids as well as decrease of organic matter and nutrient removal efficiencies. Monitoring of the effluent characteristics during this period reported over 90% for organic load, 85% of nutrient removal and over 90% of phenol and cyanide removal in SBR, while the removal efficiencies for the CSTR were 75, 65 and 80% respectively.

SBR Technology Used for Advanced Combined Municipal and Tannery Wastewater Treatment with High Receiving Water Standards

1999 ◽  
Vol 40 (4-5) ◽  
pp. 451-458 ◽  
Author(s):  
J. Banas ◽  
E. Plaza ◽  
W. Styka ◽  
J. Trela
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Treatment Plant ◽  
Tannery Wastewater ◽  
Wastewater Management ◽  
Process Performance ◽  
Biological Phosphorus Removal ◽  
Process Technology ◽  
Plant Operation

The wastewater treatment plant (WWTP) in Nowy Targ, Poland, is the largest in Europe based on classical sequencing batch reactor (SBR) technology. The plant was completed in April 1995 as one of the essential elements in a program for the protection of the water quality in the Czorsztyn Reservoir. The process technology was designed for application to a typical municipal wastewater with a separate unit to treat tannery wastewater containing chromium. Experience from plant operation showed that the municipal wastewater inflow to the WWTP included tannery wastewater with increasing chromium concentrations, caused by poor wastewater management in the city. The average value in the influent was around 3 mg Cr/l (1996-1997) and showed an increasing trend. Investigations were focused on identification of the factors affecting the process performance. In this paper, evaluation of the treatment efficiency and process performance during 2 years of plant operation is presented, including studies of nitrification, denitrification and biological phosphorus removal. A cycle analysis was performed to investigate the reduction of different parameters during different phases of a cycle. Results of a sludge activity study based on OUR, AUR and NUR tests are presented and discussed.

Long term experiences of sequencing batch reactor-system and wetland treatment from a municipal wastewater treatment plant in Sweden, operated with low temperature wastewater

2014 ◽  
Vol 9 (2) ◽  
pp. 235-242 ◽  
Author(s):  
S. Morling ◽  
A. Franquiz ◽  
J. Måhlgren ◽  
Å. Westlund
Keyword(s):  
Wastewater Treatment ◽  
Low Temperature ◽  
Wastewater Treatment Plant ◽  
Sequencing Batch Reactor ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Combined Treatment ◽  
Treatment Plant ◽  
Municipal Wastewater Treatment ◽  
Total N

A biological wastewater treatment plant, Nynäshamn treating municipal wastewater and septic sludge operated with a combination of sequencing batch reactor (SBR) units and constructed wetland is presented in this paper. The plant has to treat low temperature wastewater in winter time, still with demands for a biological nitrogen removal. Treatment results from a 13 year operation period are presented. Special attention was given to the nutrient removal during low temperature conditions. The combination of a SBR system along with classical chemical precipitation and a polishing step based on ‘natural’ extensive treatment has been a sustainable way to keep the discharge levels low. The combined treatment with SBR and the wetland at the Nynäshamn plant has resulted in improved discharge levels typically as follows (annual mean values); BOD7 3 mg/l, to be compared with the formal consent value of <15 mg/l, total P < 0.1 mg/l, to be compared with the formal consent value of <0.5 mg/l and total N 7 mg/l, to be compared with the formal consent value of <15 mg/l. It is also important to underline that the change of process train has resulted in a substantial saving of the precipitant agent for phosphorus removal. The needed dosage is now 50% of the previous dose, before the implementation of the SBR-units.

Sign in / Sign up

Export Citation Format

Share Document