A submerged tubular ceramic membrane bioreactor for high strength wastewater treatment

2003 ◽  
Vol 47 (1) ◽  
pp. 105-111 ◽  
Author(s):  
D.D. Sun ◽  
J.L. Zeng ◽  
J.H. Tay
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Retention Time ◽  
Membrane Bioreactor ◽  
Ceramic Membrane ◽  
Treatment Plant ◽  
High Strength ◽  
Cod Removal ◽  
Utilization Rate ◽  
Cod Removal Efficiency

A 4 L submerged tubular ceramic membrane bioreactor (MBR) was applied in laboratory scale to treat 2,400 mg-COD/L high strength wastewater. A prolonged sludge retention time (SRT) of 200 day, in contrast to the conventional SRT of 5 to 15 days, was explored in this study, aiming to reduce substantially the amount of disposed sludge. The MBR system was operated for a period of 142 days in four runs, differentiated by specific oxygen utilization rate (SOUR) and hydraulic retention time (HRT). It was found that the MBR system produced more than 99% of suspended solid reduction. Mixed liquor suspended solids (MLSS) was found to be adversely proportional to HRT, and in general higher than the value from a conventional wastewater treatment plant. A chemical oxygen demand (COD) removal efficiency was achieved as high as 98% in Run 1, when SOUR was in the range of 100-200 mg-O/g-MLVSS/hr. Unexpectedly, the COD removal efficiency in Run 2 to 4 was higher than 92%, on average, where higher HRT and abnormally low SOUR of 20-30 mg-O/g-MLVSS/hr prevailed. It was noted that the ceramic membrane presented a significant soluble nutrient rejection when the microbial metabolism of biological treatment broke down.

scholarly journals PENGHILANGAN POLUTAN ORGANIK DAN PADATAN TERRSUSPENSI DI DALAM AIR LIMBAH DOMESTIK DENGAN PROSES MOVING BED BIOFILM REACTOR (MBBR)

2018 ◽  
Vol 8 (1) ◽  
Author(s):  
Nusa Idaman Said ◽  
Teguh Iman Santoso
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Retention Time ◽  
Domestic Wastewater ◽  
Biofilm Reactor ◽  
Cod Removal ◽  
Aeration Tank ◽  
Moving Bed Biofilm Reactor ◽  
Moving Bed ◽  
Cod Removal Efficiency

One of the alternative technologies that could be used for domestic waste water treatment is the Moving Bed Biofilm Reactor (MBBR). MBBR in principle is activated sludge that is increased by adding media in to the reactor, so there are two treatments process happened inside, suspended growth and attached growth. This research is using bioball as a media which has surface area of ±210 m2/m3 by 20% volume of reactor volume. Wastewater treatment by MBBR uses variations of Hydraulic Retention time (HRT) 12, 8, 6, and 4 hours, then the parameters measured were BOD, COD, TSS, temperature, and pH. Result of the study shows that within HRT for 12 hours in aeration tank, removal efficiency of COD is 81,37%, BOD is 82,4%, and TSS is 90,05%. HRT for 8 hours, COD removal efficiency is 88,72%, BOD is 89,7%, and TSS is 92,06%. HRT for 6 hours, COD removal efficiency is 85,48%, BOD is 80,15%, and TSS is 94,85%. HRT for 4 hours, COD removal efficiency is 81,07%, BOD is 87,88%, and TSS is 94,86%. With a retention time of 4 hours, the effluent results domestic wastewater treatment using MBBR has met quality standards in accordance with KEPMEN LH no. 112 of 2003 on Domestic Wastewater Quality Standard and Jakarta Governor Regulation no. 122 of 2005 on Domestic Wastewater Management in Special Province of Jakarta. Keywords: Domestic wastewater, MBBR, bioball.

Textile Wastewater Treatment Using Combined Process of Biological Wriggle Bed and Ozone Biological Aerated Filter

2012 ◽  
Vol 441 ◽  
pp. 589-592
Author(s):  
Zhi Min Fu ◽  
Yu Gao Zhang ◽  
Xiao Jun Wang
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Cod Removal ◽  
Biological Aerated Filter ◽  
Combined Process ◽  
Cod Removal Efficiency ◽  
Aerated Filter ◽  
Textile Wastewater Treatment

A combined process of biological wriggle bed and ozone biological aerated filter was utilized to treat textile wastewater. Results showed that COD removal efficiency was almost 90.4%. The average effluent COD was 85.87 mg/L. The effluent colority was 64-32 times. This study indicated that the combined process is potentially useful for treating textile wastewater.

scholarly journals Treatment of Reactive Dye Containing Textile Wastewater using Microwave Assisted Synthesized Poly(Diallyldimethylammonium Chloride)

2018 ◽  
Vol 41 (2) ◽  
pp. 165-174
Author(s):  
Mahmudur Rahman ◽  
Masud Rana ◽  
Zinia Nasreen ◽  
Md Mainul Hossain ◽  
Ayesha Sharmin
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Reactive Dye ◽  
Cod Removal ◽  
Microwave Assisted ◽  
Diallyldimethylammonium Chloride ◽  
Cod Removal Efficiency ◽  
Textile Wastewater Treatment ◽  
Academy Of Sciences

Results on the applicability of microwave assisted synthesized poly(diallyldimethyl ammonium chloride) (polyDADMAC) in reactive dye containing textile wastewater treatment are reported. Diallyldimethylammonium chloride and poly(diallyldimethylammonium chloride) have been characterized by spectral means. The microwave assisted synthesized polyDADMAC has shown some effectiveness in textile wastewater treatment. COD removal efficiency of actual textile wastewater is below 30% whereas the standard dye sample shows about 50-60% COD removal efficiency. TDS and TSS also decreased after treatment of the wastewater with polyDADMAC.Journal of Bangladesh Academy of Sciences, Vol. 41, No. 2, 165-174, 2017

scholarly journals Toward Optimization of Wood Industry Wastewater Treatment in Microbial Fuel Cells—Mixed Wastewaters Approach

Energies ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 263 ◽  
Author(s):  
Monika Kloch ◽  
Renata Toczyłowska-Mamińska
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Municipal Wastewater ◽  
Power Production ◽  
Cod Removal ◽  
Treatment Efficiency ◽  
External Resistance ◽  
Wood Industry ◽  
Cod Removal Efficiency ◽  
Industry Wastewater

Microbial fuel cell (MFC) has the potential to become a promising sustainable technology of wastewater treatment. Usually, the investigations on MFCs are aimed at maximized power production in the system. In this article, we focused on the optimization of wood industry wastewater treatment in MFC, in combination with municipal wastewater as a source of microorganisms. We investigated the influence of different external resistance (2000 Ω, 1000 Ω, 500 Ω, and 100 Ω) on power density and wastewater treatment efficiency (chemical oxygen demand (COD) removal) in 1-month MFC operation time. We found that the highest COD removal was for MFCs under R = 1000 Ω after 22 days of MFC operation, while the highest current density was obtained for the lowest applied resistance. The results imply that wastewater treatment parameters such as resistance and time of MFC operation should be a subject of optimization for each specific type of wastewater used, in order to maximize either wastewater treatment efficiency or power production in MFC. Thus, optimization of power production and COD removal efficiency in MFCs need to be run separately as different resistances are required for maximizing these two parameters. When COD removal efficiency is a subject of optimization, there is no universal value of external resistance, but it should be set to the specific wastewater characteristics.

Anaerobic Fluidized-Bed Treatment of Brewery Wastes and Bioenergy Recovery

1989 ◽  
Vol 21 (12) ◽  
pp. 1681-1684 ◽  
Author(s):  
I. Ozturk ◽  
G. K. Anderson ◽  
C. B. Saw
Keyword(s):  
Fluidized Bed ◽  
Removal Efficiency ◽  
Cod Removal ◽  
Organic Loading Rate ◽  
Utilization Rate ◽  
Specific Substrate ◽  
Cod Removal Efficiency ◽  
Start Up ◽  
Specific Substrate Utilization Rate ◽  
Brewery Wastes

This paper presents the results of a pilot plant study using an Anaerobic Fluidized Bed Reactor (AFBR) for treatment of brewery wastes. A COD removal efficiency of greater than 75% was observed at an organic loading rate (OLR) of 9.5 kg COD/m3-day for a Deriod of 82 days from start-up. COD removal efficiency was greater than 74% at an OLR of 14.6 kg COD/m3 expanded bed (e.b)-day. A COD to methane conversion of 87% was achieved. Experimental results have suggested that the COD removal efficiency of an AFBR is only a function of COD loading, and neither the feed COD nor HRT alone significantly affect the performance of the reactor. A linear relationship was found between the specific substrate utilization rate and the specific methane production rate. It was observed that the distribution of the biomass along the height of the reactor is not uniform, and the biomass hold-up near the top of the reactor may reach concentrations of greater than 20,000 mg/l.

scholarly journals Dynamics of Archaeal and Bacterial Communities in Response to Variations of Hydraulic Retention Time in an Integrated Anaerobic Fluidized-Bed Membrane Bioreactor Treating Benzothiazole Wastewater

Archaea ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Yue Li ◽  
Qi Hu ◽  
Da-Wen Gao
Keyword(s):  
Fluidized Bed ◽  
Removal Efficiency ◽  
Retention Time ◽  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Hydraulic Retention Time ◽  
Oxygen Demand ◽  
High Strength ◽  
Service Period ◽  
Miseq Platform

An integrated anaerobic fluidized-bed membrane bioreactor (IAFMBR) was investigated to treat synthetic high-strength benzothiazole wastewater (50 mg/L) at a hydraulic retention time (HRT) of 24, 18, and 12 h. The chemical oxygen demand (COD) removal efficiency (from 93.6% to 90.9%), the methane percentage (from 70.9% to 69.27%), and the methane yield (from 0.309 m3 CH4/kg·CODremoved to 0.316 m3 CH4/kg·CODremoved) were not affected by decreasing HRTs. However, it had an adverse effect on membrane fouling (decreasing service period from 5.3 d to 3.2 d) and benzothiazole removal efficiency (reducing it from 97.5% to 82.3%). Three sludge samples that were collected on day 185, day 240, and day 297 were analyzed using an Illumina® MiSeq platform. It is striking that the dominant genus of archaea was always Methanosaeta despite of HRTs. The proportions of Methanosaeta were 80.6% (HRT 24), 91.9% (HRT 18), and 91.2% (HRT 12). The dominant bacterial genera were Clostridium in proportions of 23.9% (HRT 24), 16.4% (HRT 18), and 15.3% (HRT 12), respectively.

Buoyant Filter Bio-Reactor (BFBR)–a novel anaerobic wastewater treatment unit

2008 ◽  
Vol 58 (2) ◽  
pp. 373-377
Author(s):  
Soosan J. Panicker ◽  
M. C. Philipose ◽  
Ajit Haridas
Keyword(s):  
Removal Efficiency ◽  
Treatment Plant ◽  
Cod Removal ◽  
Upflow Anaerobic Sludge Blanket ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Treatment Unit ◽  
Biogas Yield ◽  
Cod Removal Efficiency ◽  
Anaerobic Sludge Blanket

The Buoyant Filter Bio-Reactor (BFBR) is a novel and very efficient method for the treatment of complex wastewater. Sewage is a complex wastewater containing insoluble COD contributed by fat and proteins. The fat and proteins present in the domestic sewage cause operational problems and underperformance in the Upflow Anaerobic Sludge Blanket Reactor, used now for treating sewage anaerobically. The biogas yield from the BFBR is 0.36 m3/kg COD reduced and the methane content was about 70–80%. Production of methane by anaerobic digestion of organic waste had the benefit of lower energy costs for treatment and is thus environmentally beneficial to the society by providing a clean fuel from renewable feed stocks. The BFBR achieved a COD removal efficiency of 80–90% for an organic loading rate of 4.5 kg/m3/d at a hydraulic retention time of 3.25 hours. The effluent COD was less than 100 mg/l, thus saving on secondary treatment cost. No pretreatment like sedimentation was required for the influent to the BFBR. The BFBR can produce low turbidity effluent as in the activated sludge process (ASP). The land area required for the BFBR treatment plant is less when compared to ASP plant. Hence the problem of scarcity of land for the treatment plant is reduced. The total expenditure for erecting the unit was less than 50% as that of conventional ASP for the same COD removal efficiency including land cost.

Kinetic Analysis of COD Removal from Actual Domestic Wastewater in an Expanded Granular Sludge Bed (EGSB) Reactor

2012 ◽  
Vol 610-613 ◽  
pp. 1691-1695
Author(s):  
Chun Juan Dong ◽  
Qing Ye Pan
Keyword(s):  
Low Temperature ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Experimental Studies ◽  
Domestic Wastewater ◽  
Pollutant Removal ◽  
Cod Removal ◽  
Utilization Rate ◽  
Cod Removal Efficiency ◽  
Pollutant Removal Rate

Treatment of actual domestic wastewater at ambient temperature, even low temperature is considered to be difficult by traditional systems. The present study is related to treatment of actual domestic wastewater in an EGSB reactor. The study showed the effectiveness of biological treatment of actual domestic wastewater involving appropriate microorganism and granules in an EGSB reactor. At 26°C, the reactor was operated at 18.7kg COD.m−3.d−1 of average organic loading and 83% high COD removal efficiency, and even at the highest loading rate of 57.12kgCOD.m−3.d−1, the COD removal efficiency still could attain to 68%. Varied influent flow need to supply varied optimal and thus to ensure the optimal removal effect. Low temperature would cause pollutant removal rate decrease. However, enhancing could optimize the contact of sludge and wastewater and thus strengthen the performance effect. Modified Stover–Kincannon model was applied to data obtained from experimental studies in EGSB reactor. Treatment efficiencies of the reactor were investigated at different hydraulic retention times (0.5-1.3h) and different operation temperature (15°C, 26°C). The modified Stover–Kincannon model was best fitted to the EGSB reactor, and the substrate utilization rate( ), saturation constant value( ), and actual pollutant removal rate( ) were found to be , , and for 26°C, , , and for 15°C( before increasing ), and , , and for 15°C(after increasing ). Low temperature could cause decrease and thus cause distinct decreasing of COD removal efficiency. However, increasing could increase and accordingly increase COD removal efficiency.

scholarly journals Application of response surface methodology to optimize the COD removal efficiency of an EGSB reactor treating poultry slaughterhouse wastewater

2019 ◽  
Vol 14 (3) ◽  
pp. 507-514 ◽  
Author(s):  
Y. Williams ◽  
M. Basitere ◽  
S. K. O. Ntwampe ◽  
M. Ngongang ◽  
M. Njoya ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Treatment Process ◽  
High Strength ◽  
Cod Removal ◽  
Organic Loading Rate ◽  
Wastewater Treatment Process ◽  
Slaughterhouse Wastewater ◽  
Cod Removal Efficiency

Abstract The poultry slaughterhouse industry consumes a large volume of potable water for bird processing and equipment cleaning, which culminates in the generation of high strength poultry slaughterhouse wastewater (PSW). The wastewater contains high concentrations of organic matter, suspended solids, nitrogen and nutrients. Most poultry slaughterhouses in South Africa (SA) discharge their wastewater into the municipal sewer system after primary treatment. Due to its high strength, PSW does not meet SA's industrial discharge standards. Discharge of untreated PSW to the environment raises environmental health concerns due to pollution of local rivers and fresh water sources, leading to odour generation and the spread of diseases. Thus, the development of a suitable wastewater treatment process for safe PSW discharge to the environment is a necessity. In this study, a biological PSW treatment process using an Expanded Granular Sludge Bed (EGSB) was evaluated. Response surface methodology coupled with central composite design was used to optimize the performance of the EGSB reactor. The dependant variable used for optimization was chemical oxygen demand (COD) removal as a function of two independent variables, hydraulic retention time (HRT) and organic loading rate (OLR). The interactions between HRT, OLR and COD removal were analysed, and a two factorial (2FI) regression was determined as suitable for COD removal modelling. The optimum COD removal of 93% was achieved at an OLR of 2 g-COD/L/d and HRT of 4.8 days. The model correlation coefficient (R2) of 0.980 indicates that it is a good fit and is suitable for predicting the EGSB's COD removal efficiency.

Sign in / Sign up

Export Citation Format

Share Document