On the Bifurcation of Rectangular Orifice Synthetic Jets

2019 ◽  
Author(s):  
Abhay Kumar ◽  
Arun K Saha ◽  
Pradipta K Panigrahi ◽  
Ashish Karn
Keyword(s):  
Synthetic Jets

THE CONTROLLING EFFECT OF SYNTHETIC JETS ON THE FLOW AROUND A RECTANGULAR WING AT SPEEDS CLOSE TO TAKEOFF AND LANDING SPEEDS

2019 ◽  
Vol 50 (6) ◽  
pp. 577-592
Author(s):  
Oleg Mikhailovich Karyakin ◽  
Aleksandr Gennadievich Nalivaiko ◽  
Nikolai Vasilievich Rostov ◽  
Maxim Vladimirovich Ustinov ◽  
Jacob Shmerkovich Flaxman
Keyword(s):  
Synthetic Jets ◽  
Controlling Effect

RANS Modeling and Simulations of Synthetic Jets

2004 ◽  
Author(s):  
Gianluca Iaccarino ◽  
Claudio Marongiu ◽  
Pietro Catalano ◽  
Marcello Amato
Keyword(s):  
Synthetic Jets ◽  
Modeling And Simulations ◽  
Rans Modeling

Wing tip vortex control using synthetic jets

2006 ◽  
Vol 110 (1112) ◽  
pp. 673-681 ◽  
Author(s):  
P. Margaris ◽  
I. Gursul
Keyword(s):  
Synthetic Jet ◽  
Synthetic Jets ◽  
Tip Vortex ◽  
Particle Image Velocimetry System ◽  
Driving Frequency ◽  
Velocity Measurements ◽  
Vortex Control ◽  
Image Velocimetry ◽  
Wing Tip ◽  
Jet Blowing

AbstractAn experimental investigation was conducted to study the effect of synthetic jet (oscillatory, zero net mass flow jet) blowing near the wing tip, as a means of diffusing the trailing vortex. Velocity measurements were taken, using a Particle Image Velocimetry system, around the tip and in the near wake of a rectangular wing, which was equipped with several blowing slots. The effect of the synthetic jet was compared to that of a continuous jet blowing from the same configurations. The results show that the use of synthetic jet blowing is generally beneficial in diffusing the trailing vortex and comparable to the use of continuous jet. The effect was more pronounced for the highest blowing coefficient used. The driving frequency of the jet did not generally prove to be a significant parameter. Finally, the instantaneous and the phase-locked velocity measurements helped explain the different mechanisms employed by the continuous and synthetic jets in diffusing the trailing vortex.

Micro Fluidic Jets for Thermal Management of Electronics

Volume 4 ◽  
2004 ◽  
Author(s):  
Jivtesh Garg ◽  
Mehmet Arik ◽  
Stanton Weaver ◽  
Seyed Saddoughi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heated Surface ◽  
Turbulent Jets ◽  
Harmonic Signal ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Small Scale ◽  
Air Cooling ◽  
Infrared Thermal Imaging

Micro fluidics devices are conventionally used for boundary layer control in many aerospace applications. Synthetic Jets are intense small scale turbulent jets formed from entrainment and expulsion of the fluid in which they are embedded. The idea of using synthetic jets in confined electronic cooling applications started in late 1990s. These micro fluidic devices offer very efficient, high magnitude direct air-cooling on the heated surface. A proprietary synthetic jet designed in General Electric Company was able to provide a maximum air velocity of 90 m/s from a 1.2 mm hydraulic diameter rectangular orifice. An experimental study for determining the thermal performance of a meso scale synthetic jet was carried out. The synthetic jets are driven by a time harmonic signal. During the experiments, the operating frequency for jets was set between 3 and 4.5 kHz. The resonance frequency for a particular jet was determined through the effect on the exit velocity magnitude. An infrared thermal imaging technique was used to acquire fine scale temperature measurements. A square heater with a surface area of 156 mm2 was used to mimic the hot component and extensive temperature maps were obtained. The parameters varied during the experiments were jet location, driving jet voltage, driving jet frequency and heater power. The output parameters were point wise temperatures (pixel size = 30 μm), and heat transfer enhancement over natural convection. A maximum of approximately 8 times enhancement over natural convection heat transfer was measured. The maximum coefficient of cooling performance obtained was approximately 6.6 due to the low power consumption of the synthetic jets.

Sign in / Sign up

Export Citation Format

Share Document