Flow with Convective Heat Transfer through a Rotating Curved Duct with Rectangular Cross-Section

2016 ◽  
Author(s):  
Tahera Khatun
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Rectangular Cross Section ◽  
Curved Duct

Heat Transfer Enhancement and Turbulent Flow in a Rectangular Channel Using Perforated Ribs With Inclined Holes

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Jian Liu ◽  
Safeer Hussain ◽  
Wei Wang ◽  
Lei Wang ◽  
Gongnan Xie ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Rectangular Cross Section ◽  
Rectangular Channel ◽  
Secondary Flows ◽  
Internal Cooling ◽  
Detached Eddy Simulation ◽  
Inclined Angle

In internal cooling passages in a turbine blade, rib structures are widely applied to augment convective heat transfer by the coolant passing through over the ribbed surfaces. This study concentrates on perforated 90 deg ribs with inclined holes in a cooling duct with rectangular cross section, aiming at improving the perforated holes with additional secondary flows caused by inclined hole arrangements. Two sets of perforated ribs are used in the experiments with the inclined angle of the holes changing from 0 deg to 45 deg and the cross section are, respectively, circular and square. Steady-state liquid crystal thermography (LCT) is applied to measure the ribbed surface temperature and obtain corresponding convective heat transfer coefficients (HTCs). Two turbulence models, i.e., the k–ω shear stress transportation (SST) model and the detached eddy simulation (DES) model, are used in the numerical studies to simulate the flow fields. All the inclined cases have slightly larger overall averaged Nusselt number (Nu) than with straight cases. The enhancement ratio is approximately 1.85–4.94%. The averaged Nu in the half portion against the inclined direction is enlarged for the inclined hole cases. The inclined hole cases usually have smaller averaged Nu in the half portion along the inclined direction. For the straight hole case and small inclined angle case, the penetrated flows mix with the mainstream flows at the perforated regions. When the inclined angle is larger, the penetrated flows are pushed to the inclined direction and mixing with the approaching flows occurs just at the side of the inclined direction.

Low Dean Number Convective Heat Transfer in Helical Ducts of Rectangular Cross Section

1998 ◽  
Vol 120 (1) ◽  
pp. 84-91 ◽  
Author(s):  
D. L. Thomson ◽  
Y. Bayazitoglu ◽  
A. J. Meade
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Energy Equation ◽  
Rectangular Cross Section ◽  
Enhance Heat Transfer ◽  
Dean Number ◽  
Straight Duct

Flow in a torroidal duct is characterized by increased convective heat transfer and friction compared to a straight duct of the same cross section. In this paper the importance of the nonplanarity (torsion) of a helical duct with rectangular cross section is investigated. A previously determined low Dean number velocity solution is used in the decoupled energy equation for the hydrodynamically fully developed, thermally developing case. Torsion, known to increase the friction factor, is found to cause a decrease in the fully developed Nusselt number compared to pure torroidal flow. Therefore, it is recommended that torsion be minimized to enhance heat transfer.

Numerical Study of Turbulent Flow and Convective Heat Transfer Characteristics in Helical Rectangular Ducts

2014 ◽  
Vol 136 (12) ◽  
Author(s):  
Yunfei Xing ◽  
Fengquan Zhong ◽  
Xinyu Zhang
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Numerical Study ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Axial Direction ◽  
Outer Wall ◽  
Centrifugal Effect

Three-dimensional turbulent forced convective heat transfer and its flow characteristics in helical rectangular ducts are simulated using SST k–ω turbulence model. The velocity field and temperature field at different axial locations along the axial direction are analyzed for different inlet Reynolds numbers, different curvatures, and torsions. The causes of heat transfer differences between the inner and outer wall of the helical rectangular ducts are discussed as well as the differences between helical and straight duct. A secondary flow is generated due to the centrifugal effect between the inner and outer walls. For the present study, the flow and thermal field become periodic after the first turn. It is found that Reynolds number can enhance the overall heat transfer. Instead, torsion and curvature change the overall heat transfer slightly. But the aspect ratio of the rectangular cross section can significantly affect heat transfer coefficient.

On the Convective Heat Transfer in a Tube of Elliptic Cross Section Maintained Under Constant Wall Temperature

1986 ◽  
Vol 108 (1) ◽  
pp. 33-39 ◽  
Author(s):  
M. A. Ebadian ◽  
H. C. Topakoglu ◽  
O. A. Arnas
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Temperature Distribution ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Wall Temperature ◽  
Elliptic Cross Section ◽  
Constant Wall Temperature ◽  
Elliptic Cross

The convective heat transfer problem along the portion of a tube of elliptic cross section maintained under a constant wall temperature where hydrodynamically and thermally fully developed flow conditions prevail is solved in this paper. The successive approximation method is used for the solution utilizing elliptic coordinates. Analytical expressions for temperature distribution and Nusselt number corresponding to the first cycle of approximation are obtained in terms of the ellipticity of the cross section. In the case of a circular section, the first cycle approximation of the Nusselt number is obtained as 3.7288 compared to the exact value of 3.6568. Representative temperature distribution curves are plotted and compared to those corresponding with constant wall heat flux conditions.

A Numerical Study of Assisting and Opposing Mixed Convective Heat Transfer From a Horizontal Isothermal High Aspect Ratio Rectangular Cylinder

2012 ◽  
Author(s):  
Patrick H. Oosthuizen
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Numerical Study ◽  
Rectangular Cross Section ◽  
Boussinesq Approximation ◽  
Forced Flow ◽  
Width Ratio ◽  
Flow Conditions ◽  
Rectangular Cylinder

Mixed convective heat transfer from an isothermal cylinder with a rectangular cross-section and a relatively large height-to-width ratio has been numerically studied. The axis of the cylinder is horizontal with the longer sides of the rectangular cylinder being vertical. There is a vertical forced flow over the cylinder. The flow conditions considered are such that in general mixed forced and natural convective flow exists. Both the case where the buoyancy forces act in the same direction as the forced flow (assisting flow) and the case where they act in the opposite direction to the forced flow (opposing flow) have been considered. The flow has been assumed to be two-dimensional and the Boussinesq approximation has been adopted. Attention has been restricted to the flow of air and results have therefore been obtained for a Prandtl number of 0.74. The flow conditions considered are such that laminar or turbulent flow can exist. The main attention is this work has been directed at determining the effect of the flow parameters on the mean heat transfer rate from the cylinder and on determining the conditions under which the flow can be assumed to be forced convective and under which it can be assumed to be natural convective.

scholarly journals Unsteady Solutions with Convective Heat Transfer through a Curved Duct Flow

2013 ◽  
Vol 56 ◽  
pp. 141-148 ◽  
Author(s):  
Rabindra Nath Mondal ◽  
Md. Saidul Islam ◽  
Md. Kutub Uddin
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Duct Flow ◽  
Curved Duct
Sign in / Sign up

Export Citation Format

Share Document