Experimental Data, Numerical Fit, and Fatigue Life Calculations Relating to the Bauschinger Effect in High-Strength Armament Steels

2003 ◽  
Author(s):  
Edward Troiano ◽  
Anthony P. Parker ◽  
John Underwood ◽  
Charles Mossey
Keyword(s):  
Experimental Data ◽  
Fatigue Life ◽  
Bauschinger Effect ◽  
High Strength ◽  
Numerical Fit

Experimental Data, Numerical Fit and Fatigue Life Calculations Relating to the Bauschinger Effect in High Strength Armament Steels

2003 ◽  
Vol 125 (3) ◽  
pp. 330-334 ◽  
Author(s):  
Edward Troiano ◽  
Anthony P. Parker ◽  
John Underwood ◽  
Charles Mossey
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Bauschinger Effect ◽  
High Strength Steels ◽  
High Strength ◽  
Strength Reduction ◽  
Plastic Strains ◽  
Test Results ◽  
Effect Factor ◽  
Modulus Reduction

The uniaxial Bauschinger effect has been evaluated in several high strength steels being considered for armament application. The steels investigated include ASTM A723 (1130 and 1330 MPa), PH 13-8 Mo stainless steel (1380 MPa), PH 13-8 Mo super tough stainless steel (1355 MPa), and HY 180 (1180MPa). Tests were conducted at plastic strains up to 3.5%. Results of testing show a progressive decrease in Bauschinger effect up to plastic strains of approximately 1% (for all materials investigated), after which there is little further decrease in the Bauschinger effect. Several key features were discovered during testing. First, all of the materials tested exhibited a changing modulus, where the elastic modulus on unloading after tensile plastic straining is consistently lower than that observed in the original loading of the specimens. The amount of modulus reduction is dependent upon the material tested, and larger reductions are observed with increasing amounts of tensile plastic strain. Prior work by Milligan reported Bauschinger effect factor β for a modified 4340 steel (old vintage A723 steel), which compares well with the present work. However, his results failed to mention any observations about a modulus reduction. The second observation was the expected strength reduction where a reduced compressive strength is observed as a result of prior tensile plastic straining. Numerical curve fits used to calculate residual stresses, which take into account both the modulus reduction and strength reduction are presented for all materials. Fatigue life calculations, utilizing the numerical curve fits, show good agreement with full size A723 laboratory fatigue test results.

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

scholarly journals Fatigue Life Improvement of Cracked Aluminum 6061-T6 Plates Repaired by Composite Patches

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1421
Author(s):  
Armin Yousefi ◽  
Saman Jolaiy ◽  
Reza Hedayati ◽  
Ahmad Serjouei ◽  
Mahdi Bodaghi
Keyword(s):  
Fatigue Life ◽  
Fatigue Behavior ◽  
Weight Ratio ◽  
High Strength ◽  
Plastic Strain Amplitude ◽  
Composite Patch ◽  
Life Improvement ◽  
Cracked Structures ◽  
Aluminum Plates ◽  
High Flexibility

Bonded patches are widely used in several industry sectors for repairing damaged plates, cracks in metallic structures, and reinforcement of damaged structures. Composite patches have optimal properties such as high strength-to-weight ratio, easiness in being applied, and high flexibility. Due to recent rapid growth in the aerospace industry, analyses of adhesively bonded patches applicable to repairing cracked structures have become of great significance. In the present study, the fatigue behavior of the aluminum alloy, repaired by a double-sided glass/epoxy composite patch, is studied numerically. More specifically, the effect of applying a double-sided composite patch on the fatigue life improvement of a damaged aluminum 6061-T6 is analyzed. 3D finite element numerical modeling is performed to analyze the fatigue performance of both repaired and unrepaired aluminum plates using the Abaqus package. To determine the fatigue life of the aluminum 6061-T6 plate, first, the hysteresis loop is determined, and afterward, the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted and validated against the available experimental data from the literature. Results reveal that composite patches increase the fatigue life of cracked structures significantly, ranging from 55% to 100% for different applied stresses.

Influence of the pore morphology of high strength concrete on its fatigue life

2018 ◽  
Vol 112 ◽  
pp. 106-116 ◽  
Author(s):  
Miguel A. Vicente ◽  
Dorys C. González ◽  
Jesús Mínguez ◽  
Manuel A. Tarifa ◽  
Gonzalo Ruiz ◽  
...  
Keyword(s):  
Fatigue Life ◽  
High Strength Concrete ◽  
High Strength ◽  
Pore Morphology ◽  
Strength Concrete

scholarly journals Multiaxial fatigue study on steel transversal attachments under constant amplitude proportional and non-proportional loadings

2018 ◽  
Vol 165 ◽  
pp. 16007
Author(s):  
Martin Garcia ◽  
Claudio A. Pereira Baptista ◽  
Alain Nussbaumer
Keyword(s):  
Fatigue Life ◽  
High Strength ◽  
Fatigue Tests ◽  
Multiaxial Fatigue ◽  
Life Assessment ◽  
Experimental Program ◽  
Proportional Loading ◽  
Load Carrying ◽  
Stress States ◽  
Experimental Values

In this study, the multiaxial fatigue strength of full-scale transversal attachment is assessed and compared to original experimental results and others found in the literature. Mild strength S235JR steel is used and an exploratory investigation on the use of high strength S690QL steel and the effect of non-proportional loading is presented. The study focuses on non-load carrying fillet welds as commonly used in bridge design and more generally between main girders and struts. The experimental program includes 33 uniaxial and multiaxial fatigue tests and was partially carried out on a new multiaxial setup that allows proportional and non-proportional tests in a typical welded detail. The fatigue life is then compared with estimations obtained from local approaches with the help of 3D finite element models. The multiaxial fatigue life assessment with some of the well-known local approaches is shown to be suited to the analysis under multiaxial stress states. The accuracy of each models and approaches is compared to the experimental values considering all the previously cited parameters.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Low-cycle fatigue behaviour of laser welded high-strength steel DOMEX 700 MC

2018 ◽  
Vol 157 ◽  
pp. 05013 ◽  
Author(s):  
Peter Kopas ◽  
Milan Sága ◽  
František Nový ◽  
Bohuš Leitner
Keyword(s):  
Fatigue Life ◽  
Welded Joints ◽  
High Strength Steel ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
High Strength ◽  
Fatigue Behaviour ◽  
Total Strain Amplitude ◽  
Cycle Fatigue ◽  
Fatigue Life Analysis

The article presents the results of research on low cycle fatigue strength of laser welded joints vs. non-welded material of high-strength steel DOMEX 700 MC. The tests were performed under load controlled using the total strain amplitude ɛac. The operating principle of the special electro-mechanic fatigue testing equipment with a suitable clamping system was working on 35 Hz frequency. Fatigue life analysis was conducted based on the Manson-Coffin-Basquin equation, which made it possible to determine fatigue parameters. Studies have shown differences in the fatigue life of original specimens and laser welded joints analysed, where laser welded joints showed lower fatigue resistance. In this article a numerical analysis of stresses generated in bending fatigue specimens has been performed employing the commercially available FEM-program ADINA.

Development of a High Strength Mg-Zn-Y-Zr Wrought Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 1701-1706
Author(s):  
Rong Shi Chen ◽  
Wei Neng Tang ◽  
Dao Kui Xu ◽  
En Hou Han
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Fatigue Life ◽  
Deformation Behavior ◽  
Fatigue Behavior ◽  
High Strength ◽  
Zn Content ◽  
High Fatigue ◽  
Content Range ◽  
Zr Alloy

The effects of Y addition to the Mg-Zn-Y-Zr alloy on the change of the microstructure and the mechanical properties (with the Y content range of 1 to 3 wt%) have been investigated. It shows that when Zn content is constant (5.65wt%), the alloys with Y content between 1.17 and 1.72wt% nearly reach its highest strength. With the composition near the optimums, the extruded Mg-6%Zn-1%Y-Zr alloy shows high strength and excellent ductility. The deformation behavior of this new alloy at high temperature has also been studied. Moreover, the super-long fatigue behavior of the Mg-6%Zn-1%Y-Zr alloy has also been tested, the results show the alloy with a high fatigue strength of about 85-90MPa in the super-long fatigue life regime of 1×109 cycles.

Impact Simulation of a Crashworthy Composite Fuselage Section with Energy-Absorbing Floor

2014 ◽  
Vol 529 ◽  
pp. 102-107
Author(s):  
Hai Bo Luo ◽  
Ying Yan ◽  
Xiang Ji Meng ◽  
Tao Tao Zhang ◽  
Zu Dian Liang
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Dynamic Response ◽  
Relative Error ◽  
High Strength ◽  
Computer Code ◽  
Impact Simulation ◽  
Average Acceleration ◽  
Simulation Results ◽  
Energy Absorbing

A 7.8m/s vertical drop simulate of a full composite fuselage section was conducted with energy-absorbing floor to evaluate the crashworthiness features of the fuselage section and to predict its dynamic response to dummies in future. The 1.52m diameter fuselage section consists of a high strength upper fuselage frame, one stiff structural floor and an energy-absorbing subfloor constructed of Rohacell foam blocks. The experimental data from literature [6] were analyzed and correlated with predictions from an impact simulation developed using the nonlinear explicit transient dynamic computer code MSC.Dytran. The simulated average acceleration did not exceed 13g, by contrast with experimental results, whose relative error is less than 11%. The numerical simulation results agree with experiments well.

Sign in / Sign up

Export Citation Format

Share Document