Characterization of Nonlinear Polymers for High-speed Photonic Response and Nonlinear Dispersion

1998 ◽  
Author(s):  
Andre Knoesen
Keyword(s):  
High Speed ◽  
Nonlinear Dispersion

Fabrication and characterization of novel high-speed InGaAs/InP uni-traveling-carrier photodetector for high responsivity

2015 ◽  
Vol 24 (10) ◽  
pp. 108506
Author(s):  
Qing-Tao Chen ◽  
Yong-Qing Huang ◽  
Jia-Rui Fei ◽  
Xiao-Feng Duan ◽  
Kai Liu ◽  
...  
Keyword(s):  
High Speed ◽  
High Responsivity ◽  
Fabrication And Characterization

Characterization of Sulfur-Cured Styrene-Butadiene Copolymer Rubbers and Their Polybutadiene Blends

1970 ◽  
Vol 43 (6) ◽  
pp. 1332-1339 ◽  
Author(s):  
J. K. Clark ◽  
R. A. Scott
Keyword(s):  
Carbon Disulfide ◽  
High Speed ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Absorption Bands ◽  
Rubber Blends ◽  
Cast Films ◽  
Micro Structures ◽  
Styrene Butadiene

Abstract Dissolution of sulfur-cured, carbon black-loaded copolymers and their blends with cis-1,4-polybutadiene (PBD) are brought about by boiling with o-dichlorobenzene which contains a small amount of 2,2′-dibenzamidodiphenyl disulfide. The resulting slurries are subjected to a sequence of separations which include high-speed centrifugation to remove solids, and solvent precipitation followed by filtration to isolate the precipitates. The precipitates are washed with solvent to remove soluble organic materials followed by carbon disulfide washing to dissolve the polymers. Cast films of the polymers are obtained by evaporating the carbon disulfide washings onto sodium chloride discs. The infrared spectra of the cast films of these preparations are very similar to those of their respective polymers prior to loading and curing. Calculations for relative concentrations of bound styrene and PBD micro-structures permit nominal identification of the kinds of styrene-butadiene rubber and the amounts of cis-1,4-PBD used in a cured rubber formulation. Absorption bands used are near 3.35 μ for cis-1,4-PBD, 6.65 μ for bound styrene, 10.35 μ for trans-1,4-PBD; and 11.0 μ for vinyl-1,2-PBD. Efforts are being made to improve the data by using a grating infrared instrument and also to extend the calibrations to include other rubber blends.

Anin situatomic force microscope for normal-incidence nanofocus X-ray experiments

2016 ◽  
Vol 23 (5) ◽  
pp. 1110-1117 ◽  
Author(s):  
M. V. Vitorino ◽  
Y. Fuchs ◽  
T. Dane ◽  
M. S. Rodrigues ◽  
M. Rosenthal ◽  
...  
Keyword(s):  
Thin Film ◽  
Atomic Force Microscope ◽  
High Speed ◽  
Normal Incidence ◽  
Organic Thin Film ◽  
X Ray ◽  
Atomic Force ◽  
Synchrotron Beamlines

A compact high-speed X-ray atomic force microscope has been developed forin situuse in normal-incidence X-ray experiments on synchrotron beamlines, allowing for simultaneous characterization of samples in direct space with nanometric lateral resolution while employing nanofocused X-ray beams. In the present work the instrument is used to observe radiation damage effects produced by an intense X-ray nanobeam on a semiconducting organic thin film. The formation of micrometric holes induced by the beam occurring on a timescale of seconds is characterized.

Characterization of Rotating Cavitation in a High Speed Inducer of Liquid Rocket Engine

2011 ◽  
Vol 320 ◽  
pp. 196-201
Author(s):  
Fei Tang ◽  
Li Jia Wen
Keyword(s):  
High Speed ◽  
High Performance ◽  
Rocket Engine ◽  
Liquid Rocket Engine ◽  
Blade Surface ◽  
Cavitation Phenomenon ◽  
Flow Fluctuations ◽  
Blade Cascade ◽  
Liquid Rocket

Rotating cavitation is one of the most important problems in the development of modern high performance rocket pump inducers. In this paper, a numerical simulation of rotating cavitation phenomenon in a 2D blade cascade of liquid rocket engine inducer was carried out using a mixture model based on Rayleigh-Plesset equation. The purpose is to investigate the characterization of rotating cavitation in a high speed inducer. The results show that when sub-synchronous rotating cavitation occurs, the speed for the length of the blade surface cavitation is lower than the speed frequency of rotation shaft with the same direction. The external aspect is that the pressure at the upstream of blades changes synchronous. Thus, the generation of sub-synchronous rotating cavitation is closely related to the changes of flow angel which caused by the flow fluctuations. Hence, elimination of the flow rate redistribution among the flow channel can effectively suppress the occurrence of this phenomenon.

Characterization of ultra-high-speed pseudomorphic AlGaAs/InGaAs (on GaAs) MODFETs

1989 ◽  
Vol 36 (10) ◽  
pp. 2243-2248 ◽  
Author(s):  
L.D. Nguyen ◽  
P.J. Tasker ◽  
D.C. Radulescu ◽  
L.F. Eastman
Keyword(s):  
High Speed ◽  
Ultra High Speed
Sign in / Sign up

Export Citation Format

Share Document