FULL SCALE TESTS OF THE XV-4A HUMMINGBIRD IN THE AMES 40 X 80 FOOT WIND TUNNEL

1965 ◽  
Author(s):  
Jr Barnes ◽  
O. G.
Keyword(s):  
Wind Tunnel ◽  
Full Scale ◽  
Full Scale Tests

scholarly journals Full-Scale-Tests of Snow and Ice with Wind Tunnel

2018 ◽  
Vol 43 (2) ◽  
pp. 155-158
Author(s):  
Takuya TSUTSUMI
Keyword(s):  
Wind Tunnel ◽  
Full Scale ◽  
Full Scale Tests ◽  
Snow And Ice

Pressure Distributions on Sails Investigated Using Three Methods: On-Water Measurements, Wind-Tunnel Measurements, and Computational Fluid Dynamics

2011 ◽  
Author(s):  
Ignazio Maria Viola ◽  
Richard G. J. Flay
Keyword(s):  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Full Scale ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Wind Tunnel Tests ◽  
Pressure Distributions ◽  
Unstable Environment ◽  
Full Scale Tests ◽  
Good Agreement

The main results of a two-year project aimed at comparing full-scale tests, wind tunnel tests, and numerical analysis predictions are presented. Pressure measurements were obtained from both full-scale tests and wind-tunnel tests, in upwind and downwind conditions. The upwind wind tunnel test condition was modelled using a Vortex Lattice code, while the downwind wind-tunnel test was modelled using a Navier-Stokes code. The pressures obtained from the three different methods are compared on three horizontal sections of the headsail, mainsail, and asymmetric spinnaker. In general the pressures from the three experiments showed good agreement. In particular, very good agreement was obtained between the numerical computations and the wind tunnel test results. Conversely, the results from the downwind full-scale pressure measurements showed less similarity due to a slightly tightened trim being used for the spinnaker in the on-water tests. Full-scale tests allow the action of unsteadiness due to the wind, wave and yacht movements to affect the results. This unstable environment caused the asymmetric spinnaker to move around, and a tightened trim was required to prevent the spinnaker from collapsing.

Wind Tunnel to Full Scale Mapping of Winds and Loads for Launch-Vehicle Ground Wind Loads

2021 ◽  
Author(s):  
Thomas G. Ivanco ◽  
Donald F. Keller ◽  
Jennifer L. Pinkerton
Keyword(s):  
Wind Tunnel ◽  
Launch Vehicle ◽  
Full Scale ◽  
Wind Loads

Characterization of wind-induced pressure on membrane roofs based on full-scale wind tunnel testing

2021 ◽  
Vol 235 ◽  
pp. 112101
Author(s):  
Johnny Estephan ◽  
Changda Feng ◽  
Arindam Gan Chowdhury ◽  
Mauricio Chavez ◽  
Appupillai Baskaran ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Full Scale ◽  
Wind Tunnel Testing ◽  
Tunnel Testing

Investigation of planing craft maneuverability using full-scale tests

2021 ◽  
pp. 147509022110303
Author(s):  
Kazem Sadati ◽  
Hamid Zeraatgar ◽  
Aliasghar Moghaddas
Keyword(s):  
Full Scale ◽  
Performance Characteristics ◽  
Forward Speed ◽  
Speed Reduction ◽  
Planing Craft ◽  
Full Scale Tests ◽  
Turning Maneuver

Maneuverability of planing craft is a complicated hydrodynamic subject that needs more studies to comprehend its characteristics. Planing craft drivers follow a common practice for maneuver of the craft that is fundamentally different from ship’s standards. In situ full-scale tests are normally necessary to understand the maneuverability characteristics of planing craft. In this paper, a study has been conducted to illustrate maneuverability characteristics of planing craft by full-scale tests. Accelerating and turning maneuver tests are conducted on two cases at different forward speeds and rudder angles. In each test, dynamic trim, trajectory, speed, roll of the craft are recorded. The tests are performed in planing mode, semi-planing mode, and transition between planing mode to semi-planing mode to study the effects of the craft forward speed and consequently running attitude on the maneuverability. Analysis of the data reveals that the Steady Turning Diameter (STD) of the planing craft may be as large as 40 L, while it rarely goes beyond 5 L for ships. Results also show that a turning maneuver starting at planing mode might end in semi-planing mode. This transition can remarkably improve the performance characteristics of the planing craft’s maneuverability. Therefore, an alternative practice is proposed instead of the classic turning maneuver. In this practice, the craft traveling in the planing mode is transitioned to the semi-planing mode by forward speed reduction first, and then the turning maneuver is executed.

Full-scale tests of the trash racks of the Kapchagai hydroelectric station

1984 ◽  
Vol 18 (4) ◽  
pp. 166-170
Author(s):  
A. L. Rakhmanova ◽  
I. O. Rybak
Keyword(s):  
Hydroelectric Station ◽  
Full Scale ◽  
Full Scale Tests
Sign in / Sign up

Export Citation Format

Share Document