Using Real-Time Pressure Data for Well Placement Planning

2006 ◽  
Author(s):  
Mike Parker ◽  
Robert N. Bradford ◽  
Laurence Ward Corbett ◽  
Robin Noel Heim ◽  
Christina Leigh Isakson ◽  
...  
Keyword(s):  
Real Time ◽  
Time Pressure ◽  
Pressure Data ◽  
Well Placement

Integrating Images From Multiple Depths of Investigation and Quantitative Signal Inversion in Real Time For Accurate Well Placement

2008 ◽  
Author(s):  
Roland E. Chemali ◽  
Michael S. Bittar ◽  
Frode Hveding ◽  
Min Wu ◽  
Michael Raymond Dautel
Keyword(s):  
Real Time ◽  
Well Placement ◽  
Signal Inversion

A Novel Workflow for Geosteering a Horizontal Well in a Low Resistivity Contrast Anisotropic Environment: A Case Study in Semoga Field, Indonesia

2021 ◽  
Author(s):  
Yessica Fransisca ◽  
Karinka Adiandra ◽  
Vinda Manurung ◽  
Laila Warkhaida ◽  
M. Aidil Arham ◽  
...  
Keyword(s):  
Real Time ◽  
Horizontal Well ◽  
Gamma Ray ◽  
Lessons Learned ◽  
Electrical Anisotropy ◽  
Anisotropy Ratio ◽  
Well Placement ◽  
Low Contrast ◽  
Low Resistivity ◽  
The Subject

Abstract This paper describes the combination of strategies deployed to optimize horizontal well placement in a 40 ft thick isotropic sand with very low resistivity contrast compared to an underlying anisotropic shale in Semoga field. These strategies were developed due to previously unsuccessful attempts to drill a horizontal well with multiple side-tracks that was finally drilled and completed as a high-inclined well. To maximize reservoir contact of the subject horizontal well, a new methodology on well placement was developed by applying lessons learned, taking into account the additional challenges within this well. The first approach was to conduct a thorough analysis on the previous inclined well to evaluate each formation layer’s anisotropy ratio to be used in an effective geosteering model that could better simulate the real time environment. Correct selections of geosteering tools based on comprehensive pre-well modelling was considered to ensure on-target landing section to facilitate an effective lateral section. A comprehensive geosteering pre-well model was constructed to guide real-time operations. In the subject horizontal well, landing strategy was analysed in four stages of anisotropy ratio. The lateral section strategy focused on how to cater for the expected fault and maintain the trajectory to maximize reservoir exposure. Execution of the geosteering operations resulted in 100% reservoir contact. By monitoring the behaviour of shale anisotropy ratio from resistivity measurements and gamma ray at-bit data while drilling, the subject well was precisely landed at 11.5 ft TVD below the top of target sand. In the lateral section, wellbore trajectory intersected two faults exhibiting greater associated throw compared to the seismic estimate. Resistivity geo-signal and azimuthal resistivity responses were used to maintain the wellbore attitude inside the target reservoir. In this case history well with a low resistivity contrast environment, this methodology successfully enabled efficient operations to land the well precisely at the target with minimum borehole tortuosity. This was achieved by reducing geological uncertainty due to anomalous resistivity data responding to shale electrical anisotropy. Recognition of these electromagnetic resistivity values also played an important role in identifying the overlain anisotropic shale layer, hence avoiding reservoir exit. This workflow also helped in benchmarking future horizontal well placement operations in Semoga Field. Technical Categories: Geosteering and Well Placement, Reservoir Engineering, Low resistivity Low Contrast Reservoir Evaluation, Real-Time Operations, Case Studies

Implementation of Vendor-Independent Stochastic Inversion for Improving Quality and Efficiency of Well Placement on the Field of Novatek Company

2021 ◽  
Author(s):  
Danil Andreevich Nemushchenko ◽  
Pavel Vladimirovich Shpakov ◽  
Petr Valerievich Bybin ◽  
Kirill Viktorovich Ronzhin ◽  
Mikhail Vladimirovich Sviridov
Keyword(s):  
Real Time ◽  
Well Placement ◽  
Stochastic Inversion ◽  
Mathematical Algorithm ◽  
Service Companies ◽  
Resistivity Data ◽  
Resistivity Logging ◽  
Azimuthal Resistivity ◽  
Logging Tool ◽  
Single Approach

Abstract The article describes the application of a new stochastic inversion of the deep-azimuthal resistivity data, independent from the tool vendor. The new model was performed on the data from several wells of the PAO «Novatek», that were drilled using deep-azimuthal resistivity tools of two service companies represented in the global oilfield services market. This technology allows to respond in a timely manner when the well approaches the boundaries with contrasting resistivity properties and to avoid exit to unproductive zones. Nowadays, the azimuthal resistivity data is the method with the highest penetration depth for the geosteering in real time. Stochastic inversion is a special mathematical algorithm based on the statistical Monte Carlo method to process the readings of resistivity while drilling in real time and provide a geoelectrical model for making informed decisions when placing horizontal and deviated wells. Until recently, there was no unified approach to calculate stochastic inversion, which allows to perform calculations for various tools. Deep-azimuthal resistivity logging tool vendors have developed their own approaches. This article presents a method for calculating stochastic inversion. This approach was never applied for this kind of azimuthal resistivity data. Additionally, it does not depend on the tool vendor, therefore, allows to compare the data from various tools using a single approach.

Low-Cost Measurement of Hydraulic Fracture Dimensions Using Pressure Data in Treatment and Observation Wells – A Workflow for Every Well

2021 ◽  
Author(s):  
A. Kirby Nicholson ◽  
Robert C. Bachman ◽  
R. Yvonne Scherz ◽  
Robert V. Hawkes
Keyword(s):  
Hydraulic Fracturing ◽  
Real Time ◽  
Hydraulic Fracture ◽  
Full Scale ◽  
Pressure Data ◽  
Observation Well ◽  
High Quality ◽  
Fracture Length ◽  
Geometry Model ◽  
Observation Wells

Abstract Pressure and stage volume are the least expensive and most readily available data for diagnostic analysis of hydraulic fracturing operations. Case history data from the Midland Basin is used to demonstrate how high-quality, time-synchronized pressure measurements at a treatment and an offsetting shut-in producing well can provide the necessary input to calculate fracture geometries at both wells and estimate perforation cluster efficiency at the treatment well. No special wellbore monitoring equipment is required. In summary, the methods outlined in this paper quantifies fracture geometries as compared to the more general observations of Daneshy (2020) and Haustveit et al. (2020). Pressures collected in Diagnostic Fracture Injection Tests (DFITs), select toe-stage full-scale fracture treatments, and offset observation wells are used to demonstrate a simple workflow. The pressure data combined with Volume to First Response (Vfr) at the observation well is used to create a geometry model of fracture length, width, and height estimates at the treatment well as illustrated in Figure 1. The producing fracture length of the observation well is also determined. Pressure Transient Analysis (PTA) techniques, a Perkins-Kern-Nordgren (PKN) fracture propagation model and offset well Fracture Driven Interaction (FDI) pressures are used to quantify hydraulic fracture dimensions. The PTA-derived Farfield Fracture Extension Pressure, FFEP, concept was introduced in Nicholson et al. (2019) and is summarized in Appendix B of this paper. FFEP replaces Instantaneous Shut-In Pressure, ISIP, for use in net pressure calculations. FFEP is determined and utilized in both DFITs and full-scale fracture inter-stage fall-off data. The use of the Primary Pressure Derivative (PPD) to accurately identify FFEP simplifies and speeds up the analysis, allowing for real time treatment decisions. This new technique is called Rapid-PTA. Additionally, the plotted shape and gradient of the observation-well pressure response can identify whether FDI's are hydraulic or poroelastic before a fracture stage is completed and may be used to change stage volume on the fly. Figure 1Fracture Geometry Model with FDI Pressure Matching Case studies are presented showing the full workflow required to generate the fracture geometry model. The component inputs for the model are presented including a toe-stage DFIT, inter-stage pressure fall-off, and the FDI pressure build-up. We discuss how to optimize these hydraulic fractures in hindsight (look-back) and what might have been done in real time during the completion operations given this workflow and field-ready advanced data-handling capability. Hydraulic fracturing operations can be optimized in real time using new Rapid-PTA techniques for high quality pressure data collected on treating and observation wells. This process opens the door for more advanced geometry modeling and for rapid design changes to save costs and improve well productivity and ultimate recovery.

scholarly journals Real-time Pressure-volume Analysis of Acute Myocardial Infarction in Mice

10.3791/57621 ◽  
2018 ◽  
Author(s):  
Lars Michel ◽  
Pia Stock ◽  
Christos Rammos ◽  
Matthias Totzeck ◽  
Tienush Rassaf ◽  
...  
Keyword(s):  
Myocardial Infarction ◽  
Acute Myocardial Infarction ◽  
Real Time ◽  
Time Pressure ◽  
Volume Analysis
Sign in / Sign up

Export Citation Format

Share Document