A New Method for Predicting Interwell Remaining Oil Distribution in Multilayer Sandstone Reservoirs at High Water Cut Stage

2003 ◽  
Author(s):  
Qinglong Du ◽  
Bingyu Ji ◽  
Xiaoguang Lu ◽  
Lihua Xie ◽  
Yubo Lan ◽  
...  
Keyword(s):  
High Water ◽  
New Method ◽  
Oil Distribution ◽  
Remaining Oil ◽  
Remaining Oil Distribution ◽  
Sandstone Reservoirs ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

The Analysis of Remaining Oil in High Water Cut Stage

2013 ◽  
Vol 274 ◽  
pp. 675-678
Author(s):  
Cheng Fu ◽  
Bin Huang
Keyword(s):  
Characteristic Curve ◽  
Material Balance ◽  
High Water ◽  
Oil Distribution ◽  
Remaining Oil ◽  
Remaining Oil Distribution ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut ◽  
Material Balance Method

The remaining oil distribution is very complex and the difficulty in tapping measures is more and more big when the west block of South-eight area has gone into the ultra-high water cut stage. So the remaining oil distribution in 109 units has been comprehensively studied on the condition that the composite water cut reaches 9.06% by establishing reservoir geologic model and proceeding reservoir numerical simulation according to recent tapping measures and remaining oil analysis experience in the process of adjusting scheme. And combined with some reservoir engineering methods such as: waterflooding characteristic curve and material balance method, obvious effects has been obtained in this research.

Study on 3D Fine Structural Modeling of Typical Block in Sanan Oilfield, Daqing

2014 ◽  
Vol 628 ◽  
pp. 348-353
Author(s):  
Tao Li ◽  
Zian Li ◽  
Jiang Wang
Keyword(s):  
Structural Model ◽  
3D Structure ◽  
High Water ◽  
Oil Distribution ◽  
Remaining Oil ◽  
Modeling Software ◽  
Remaining Oil Distribution ◽  
High Water Cut ◽  
Reservoir Description ◽  
Water Cut

Sanan oilfield has entered late stage of high water cut development. It urgently needs accurate prediction of remaining oil distribution. But previous studies on 3D structure were far could not meet the requirements of fine reservoir description. This paper applied RMS, a piece of excellent geological modeling software establishing the 3D fine structural model of typical block in Sanan oilfield on the bases of 3D fine seismic structural interpretation data. It included the 28 faults’ model, 11 horizons’ model and the structural model. And then measured and analyzed the faults elements data. Based on abundant geologic data, well data and seismic data of the block, this structural model reproduced the fine seismic interpretation results accurately. It was really fine enough to meet the requirements of the fine reservoir description. This research solved the problem that traditional modeling techniques could not handle complex cutting relationship of faults’ model. It laid a solid foundation for reservoir numerical simulation and remaining oil distribution prediction.

scholarly journals Study on oil displacement efficiency of offshore sandstone reservoir with big bottom water

2021 ◽  
Author(s):  
Jie Tan ◽  
Ying-xian Liu ◽  
Yan-lai Li ◽  
Chun-yan Liu ◽  
Song-ru Mou
Keyword(s):  
Bottom Water ◽  
High Water ◽  
Displacement Efficiency ◽  
Oil Displacement ◽  
Oil Displacement Efficiency ◽  
Sandstone Reservoir ◽  
Sandstone Reservoirs ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

AbstractX oilfield is a typical sandstone reservoir with big bottom water in the Bohai Sea. The viscosity of crude oil ranges from 30 to 425 cp. Single sand development with the horizontal well is adopted. At present, the water content is as high as 96%. The water cut of the production well is stable for a long time in the high water cut period. The recoverable reserves calculated by conventional methods have gradually increased, and even the partial recovery has exceeded the predicted recovery rate. This study carried out an oil displacement efficiency experiment under big water drive multiple to accurately understand an extensive bottom water reservoir's production law in an ultra-high water cut stage. It comprehensively used the scanning electron microscope date, casting thin section, oil displacement experiment, and production performance to analyze the change law of physical properties and relative permeability curve from the aspects of reservoir clay minerals, median particle size, pore distribution, and pore throat characteristics. Therefore, the development law of horizontal production wells in sandstone reservoirs with big bottom water is understood. It evaluates the ultimate recovery of sandstone reservoirs with big bottom water. It provides a fundamental theoretical basis and guidance for dynamic prediction and delicate potential tapping of sandstone reservoirs with big bottom water at a high water cut stage.

scholarly journals Microscopic Determination of Remaining Oil Distribution in Sandstones With Different Permeability Scales Using Computed Tomography Scanning

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Yongfei Yang ◽  
Haiyuan Yang ◽  
Liu Tao ◽  
Jun Yao ◽  
Wendong Wang ◽  
...  
Keyword(s):  
Distribution Pattern ◽  
Oil Recovery ◽  
Distribution Patterns ◽  
High Water ◽  
Water Flooding ◽  
Oil Distribution ◽  
Computed Tomography Scanning ◽  
Remaining Oil ◽  
High Water Cut ◽  
Water Cut

To investigate the characteristics of oil distribution in porous media systems during a high water cut stage, sandstones with different permeability scales of 53.63 × 10−3 μm2 and 108.11 × 10−3 μm2 were imaged under a resolution of 4.12 μm during a water flooding process using X-ray tomography. Based on the cluster-size distribution of oil segmented from the tomography images and through classification using the shape factor and Euler number, the transformation of the oil distribution pattern in different injection stages was studied for samples with different pore structures. In general, the distribution patterns of an oil cluster continuously change during water injection. Large connected oil clusters break off into smaller segments. The sandstone with a higher permeability (108.11 × 10−3 μm2) shows the larger change in distribution pattern, and the remaining oil is trapped in the pores with a radius of approximately 7–12 μm. Meanwhile, some disconnected clusters merge together and lead to a re-connection during the high water cut period. However, the pore structure becomes compact and complex, the residual nonwetting phase becomes static and is difficult to move; and thus, all distribution patterns coexist during the entire displacement process and mainly distribute in pores with a radius of 8–12 μm. For the pore-scale entrapment characteristics of the oil phase during a high water cut period, different enhance oil recovery (EOR) methods should be considered in sandstones correspondent to each permeability scale.

Sign in / Sign up

Export Citation Format

Share Document