Evaluation of CO2 Gas Injection For Major Oil Production Fields in Malaysia - Experimental Approach Case Study: Dulang Field

2001 ◽  
Author(s):  
Zahidah Md. Zain ◽  
Nor Idah Kechut ◽  
Ganesan Nadeson ◽  
Noraini Ahmad ◽  
D.M. Anwar Raja
Keyword(s):  
Experimental Approach ◽  
Gas Injection ◽  
Oil Production ◽  
Co2 Gas

A Geoengineering Approach to Maximum Reservoir Contact Wells Design: Case Study in a Carbonate Reservoir Under Water and Miscible Gas Injection

2021 ◽  
Author(s):  
Alfredo Freites ◽  
Victor Segura ◽  
Muhammad Muneeb
Keyword(s):  
Gas Injection ◽  
Oil Production ◽  
Carbonate Reservoir ◽  
Production Performance ◽  
Pressure Drops ◽  
Well Completion ◽  
Entry Points ◽  
Miscible Gas Injection ◽  
Well Completions

Abstract Maximum Reservoir Contact wells (MRCs) are a potential alternative to reduce the number of wells required to develop hydrocarbon reservoirs, improve sweeping efficiency and delay gas and water breakthrough. The well completions design is critical for the success of MRCs. In this study we present a case study of a MRC well completion design using Limited Entry Liners (LEL) in a mature carbonate reservoir under water and miscible gas injection. We developed an integrated workflow that considered a high-resolution numerical simulation model calibrated to static and dynamic data and wellbore-reservoir models coupling, for capturing the details of the flow interaction between both systems. Flow restrictions in the form of additional pressure drops to the flow from the reservoir into the wellbore were used to simulate the effect of small open flow areas, i.e.shot densities, in the LELs. Our work allowed identifying the most likely entry points of gas and water and design the well to minimize their impact on oil production. We observe that longer lengths open to flow outweighs the detrimental effect of producing from intervals closer to the water saturated zones. We also observed that balancing the inflow profile along the wellbore did not report beneficial results to oil production as it stimulates production from the reservoir zone from which the gas breakthrough is expected (middle of the producing section); this result is particularly relevant as it shows that designing the well completions with base only on static data could lead to poor production performance. The suggested completion for the MRC well encompasses four segments; a segment covering almost 50 % of the well length and located at the middle of the producing section with a blind liner (close to flow for gas control) and the remaining three with slotted liners with enough open area as to avoid causing significant pressure drops.

Enhancing Recovery by Concurrent Water and Gas Injection: Case Study of a Deepwater Turbidite Reservoir

2014 ◽  
Author(s):  
Chinelo Ezeudoh ◽  
Maarten Zandvliet ◽  
Timipere Jenakumo ◽  
Agatha Onuwaje ◽  
Michel Prudhomme-Nzuoba
Keyword(s):  
Gas Injection

Pilot Project Evaluating WAG Efficiency for Carbonate Reservoir in Eastern Siberia

2021 ◽  
Author(s):  
Valentina Zharko ◽  
Dmitriy Burdakov
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Oil Production ◽  
Pilot Project ◽  
Carbonate Reservoir ◽  
Recovery Factor ◽  
Eastern Siberia ◽  
Water Cut ◽  
Wag Injection ◽  
Injection Rates

Abstract The paper presents the results of a pilot project implementing WAG injection at the oilfield with carbonate reservoir, characterized by low efficiency of traditional waterflooding. The objective of the pilot project was to evaluate the efficiency of this enhanced oil recovery method for conditions of the specific oil field. For the initial introduction of WAG, an area of the reservoir with minimal potential risks has been identified. During the test injections of water and gas, production parameters were monitored, including the oil production rates of the reacting wells and the water and gas injection rates of injection wells, the change in the density and composition of the produced fluids. With first positive results, the pilot area of the reservoir was expanded. In accordance with the responses of the producing wells to the injection of displacing agents, the injection rates were adjusted, and the production intensified, with the aim of maximizing the effect of WAG. The results obtained in practice were reproduced in the simulation model sector in order to obtain a project curve characterizing an increase in oil recovery due to water-alternating gas injection. Practical results obtained during pilot testing of the technology show that the injection of gas and water alternately can reduce the water cut of the reacting wells and increase overall oil production, providing more efficient displacement compared to traditional waterflooding. The use of WAG after the waterflooding provides an increase in oil recovery and a decrease in residual oil saturation. The water cut of the produced liquid decreased from 98% to 80%, an increase in oil production rate of 100 tons/day was obtained. The increase in the oil recovery factor is estimated at approximately 7.5% at gas injection of 1.5 hydrocarbon pore volumes. Based on the received results, the displacement characteristic was constructed. Methods for monitoring the effectiveness of WAG have been determined, and studies are planned to be carried out when designing a full-scale WAG project at the field. This project is the first pilot project in Russia implementing WAG injection in a field with a carbonate reservoir. During the pilot project, the technical feasibility of implementing this EOR method was confirmed, as well as its efficiency in terms of increasing the oil recovery factor for the conditions of the carbonate reservoir of Eastern Siberia, characterized by high water cut and low values of oil displacement coefficients during waterflooding.

Undersaturated Hydrocarbon Reservoir Waterflooding: A simulation Approach to Performance Assessment

2021 ◽  
Author(s):  
Adekunle Tirimisiyu Adeniyi ◽  
Miracle Imwonsa Osatemple ◽  
Abdulwahab Giwa
Keyword(s):  
Oil Recovery ◽  
Net Present Value ◽  
Oil Production ◽  
Base Case ◽  
Present Value ◽  
Sweep Efficiency ◽  
Recovery Method ◽  
Solution Approach ◽  
Hydrocarbon Reservoir

Abstract There are a good numbers of brown hydrocarbon reservoirs, with a substantial amount of bypassed oil. These reservoirs are said to be brown, because a huge chunk of its recoverable oil have been produced. Since a significant number of prominent oil fields are matured and the number of new discoveries is declining, it is imperative to assess performances of waterflooding in such reservoirs; taking an undersaturated reservoir as a case study. It should be recalled that Waterflooding is widely accepted and used as a means of secondary oil recovery method, sometimes after depletion of primary energy sources. The effects of permeability distribution on flood performances is of concerns in this study. The presence of high permeability streaks could lead to an early water breakthrough at the producers, thus reducing the sweep efficiency in the field. A solution approach adopted in this study was reserve water injection. A reverse approach because, a producing well is converted to water injector while water injector well is converted to oil producing well. This optimization method was applied to a waterflood process carried out on a reservoir field developed by a two - spot recovery design in the Niger Delta area of Nigeria that is being used as a case study. Simulation runs were carried out with a commercial reservoir oil simulator. The result showed an increase in oil production with a significant reduction in water-cut. The Net Present Value, NPV, of the project was re-evaluated with present oil production. The results of the waterflood optimization revealed that an increase in the net present value of up to 20% and an increase in cumulative production of up to 27% from the base case was achieved. The cost of produced water treatment for re-injection and rated higher water pump had little impact on the overall project economy. Therefore, it can conclude that changes in well status in wells status in an heterogenous hydrocarbon reservoir will increase oil production.

Growth Mechanism vs Matter Transport in Thermally Growing Oxides on High Temperature Materials: A Brief Survey Based on the Case Study of Alumina Formers

2009 ◽  
Vol 289-292 ◽  
pp. 385-395 ◽  
Author(s):  
Jerzy Jedlinski
Keyword(s):  
Growth Mechanism ◽  
Experimental Approach ◽  
Experimental Results ◽  
Metallic Materials ◽  
High Temperature Materials ◽  
Matter Transport ◽  
Alumina Formers ◽  
Microstructure Morphology ◽  
The Relationship

This paper reviews briefly the relationship between the growth mechanism and matter transport using as an example the best currently applied metallic materials being alumina formers. The attention is paid to the experimental approach as well as to the interpretation procedure of experimental results. The scale structure, microstructure, morphology and phase composition are indicated as factors strongly affecting its growth mechanism. The attempt is made to elucidate the possible relationships between the obtained experimental results and actual scale growth mechanisms operating during oxidation exposures.

An Unconventional Approach to Gas Injection - A Niger Delta Field Case Study

2017 ◽  
Author(s):  
Narjes Kallel ◽  
Olugbenga Oni ◽  
Juliane Heiland ◽  
Vincenzo De Gennaro ◽  
Sunil Ramaswamy ◽  
...  
Keyword(s):  
Niger Delta ◽  
Gas Injection ◽  
Field Case
Sign in / Sign up

Export Citation Format

Share Document