Application of DFIT-FBA Tests Performed at Multiple Points in a Horizontal Well for Advanced Treatment Stage Design and Reservoir Characterization

2021 ◽  
Author(s):  
Danial Zeinabady ◽  
Behnam Zanganeh ◽  
Sadeq Shahamat ◽  
Christopher R. Clarkson
Keyword(s):  
Horizontal Well ◽  
Reservoir Characterization ◽  
Material Balance ◽  
In Situ Stress ◽  
Productivity Index ◽  
Multiple Points ◽  
Well Productivity ◽  
Balance Analysis ◽  
Flowing Material

Abstract The DFIT flowback analysis (DFIT-FBA) method, recently developed by the authors, is a new approach for obtaining minimum in-situ stress, reservoir pressure, and well productivity index estimates in a fraction of the time required by conventional DFITs. The goal of this study is to demonstrate the application of DFIT-FBA to hydraulic fracturing design and reservoir characterization by performing tests at multiple points along a horizontal well completed in an unconventional reservoir. Furthermore, new corrections are introduced to the DFIT-FBA method to account for perforation friction, tortuosity, and wellbore unloading during the flowback stage of the test. The time and cost efficiency associated with the DFIT-FBA method provides an opportunity to conduct multiple field tests without delaying the completion program. Several trials of the new method were performed for this study. These trials demonstrate application of the DFIT-FBA for testing multiple points along the lateral of a horizontal well (toe stage and additional clusters). The operational procedure for each DFIT-FBA test consists of two steps: 1) injection to initiate and propagate a mini hydraulic fracture and 2) flowback of the injected fluid on surface using a variable choke setting on the wellhead. Rate transient analysis methods are then applied to the flowback data to identify flow regimes and estimate closure and reservoir pressure. Flowing material balance analysis is used to estimate the well productivity index for studied reservoir intervals. Minimum in-situ stress, pore pressure and well productivity index estimates were successfully obtained for all the field trials and validated by comparison against a conventional DFIT. The new corrections for friction and wellbore unloading improved the accuracy of the closure and reservoir pressures by 4%. Furthermore, the results of flowing material balance analysis show that wellbore unloading might cause significant over-estimation of the well productivity index. Considerable variation in well productivity index was observed from the toe stage to the heel stage (along the lateral) for the studied well. This variation has significant implications for hydraulic fracture design optimization, particularly treatment pressures and volumes.

Flowing Material Balance Analysis and Production Optimization in HPHT Sour Gas Field

2019 ◽  
Author(s):  
Azis Hidayat ◽  
Dwi Hudya Febrianto ◽  
Elisa Wijayanti ◽  
Diniko Nurhajj ◽  
Ahmad Sujai ◽  
...  
Keyword(s):  
Material Balance ◽  
Production Optimization ◽  
Gas Field ◽  
Balance Analysis ◽  
Flowing Material ◽  
Sour Gas

scholarly journals Application of Hydrodynamic Potential Analysis to Investigate Possibility Reservoir Connectivity between Neighboring Gas Fields

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Tri Firmanto ◽  
Muhammad Taufiq Fathaddin ◽  
R. S. Trijana Kartoatmodjo
Keyword(s):  
Stone Formation ◽  
Material Balance ◽  
Gas Field ◽  
Water Contact ◽  
Potential Analysis ◽  
Balance Analysis ◽  
Hydrodynamic Potential ◽  
Flowing Material ◽  
Reservoir Connectivity ◽  
Gas Fields

<em>T field is a producting gas field in North Bali PSC, which currently producing 210 mmscfd from paciran sand stone formation. Paciran formation extends more than 20 km across the PSC area, which consists of 3 developed gas fields and one potential development field.  The flowing material balance analysis conducted on T field suggests possibility of reservoir connectivty between this field and its neighboring fields. Even though each field is already have a well defined Gas Water Contact, a thorough investigation was done using hyrdodynamic potential analysis to see if theres any hydrodynamic potential that allowed connectivity between these fields, and enable tilted contact occurred between these field. Using pressure data taken from each fields exploration wells the analysis can be conducted that conclude that there is an existing hydrodynamic potential between gas fields in paciran formation. A review on the tilted contact analysis concludes that the existing hydrodynamic potential is not enough to tilt the contact as per actually observed contact</em>.

scholarly journals Productivity Evaluation for Long Horizontal Well Test in Deep-Water Faulted Sandstone Reservoir

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Zhiwang Yuan ◽  
Li Yang ◽  
Yingchun Zhang ◽  
Rui Duan ◽  
Xu Zhang ◽  
...  
Keyword(s):  
Steady State ◽  
Deep Water ◽  
Horizontal Well ◽  
Evaluation Method ◽  
Horizontal Wells ◽  
Productivity Index ◽  
Test Time ◽  
Well Test ◽  
Well Productivity ◽  
Sandstone Reservoir

For deep-water faulted sandstone reservoirs, the general practice is to design long horizontal wells improving well productivity. During the project implementation stage, well tests are performed on all drilled wells to evaluate well productivity accurately. Furthermore, multisize chokes are often utilized in a shorten test time for loosen formation, high test cost, and high well productivity. Nevertheless, the conventional productivity evaluation approach cannot accurately evaluate the well test productivity and has difficulty in determining the underneath pattern. As a result, the objective of this paper is to determine a productivity evaluation method for multisize chokes long horizontal well test in deep-water faulted sandstone reservoir. This approach introduces a productivity model for long horizontal wells in faulted sandstone reservoir. It also includes the determination of steady-state test time and the productivity evaluation method for multisize chokes. In this paper, the EGINA Oilfield, a deep-water faulted sandstone reservoir, located in West Africa was chosen as the research target. Based on Renard and Dupuy’s steady-state equation, the relationship between the productivity index per meter and the length of horizontal section was derived. Consequently, this relationship is used to determine the productivity pattern for long horizontal wells with the same geological features, which can provide more accurate productivity evaluations for tested wells and forecast the well productivity for untested wells. After implementing this approach on the EGINA Oilfield, the determined relationship is capable to accurately evaluate the test productivity for long horizontal wells in reservoirs with similar characteristics and assist in examination and treatment for horizontal wells with abnormal productivity.

scholarly journals Flowing Material Balance and Rate-Transient Analysis of Horizontal Wells in Under-Saturated Coal Seam Gas Reservoirs: A Case Study from the Qinshui Basin, China

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4887
Author(s):  
Suyang Zhu ◽  
Alireza Salmachi
Keyword(s):  
Transient Analysis ◽  
Horizontal Well ◽  
Material Balance ◽  
Production Data ◽  
Coal Seam Gas ◽  
Two Phase ◽  
Rate Transient Analysis ◽  
Flowing Material ◽  
Phase Water ◽  
Water Gas

Two phase flow and horizontal well completion pose additional challenges for rate-transient analysis (RTA) techniques in under-saturated coal seam gas (CSG) reservoirs. To better obtain reservoir parameters, a practical workflow for the two phase RTA technique is presented to extract reservoir information by the analysis of production data of a horizontal well in an under-saturated CSG reservoir. This workflow includes a flowing material balance (FMB) technique and an improved form of two phase (water + gas) RTA. At production stage of a horizontal well in under-saturated CSG reservoirs, a FMB technique was developed to extract original water in-place (OWIP) and horizontal permeability. This FMB technique involves the application of an appropriate productivity equation representing the relative position of the horizontal well in the drainage area. Then, two phase (water + gas) RTA of a horizontal well was also investigated by introducing the concept of the area of influence (AI), which enables the calculation of the water saturation during the transient formation linear flow. Finally, simulation and field examples are presented to validate and demonstrate the application of the proposed techniques. Simulation results indicate that the proposed FMB technique accurately predicts OWIP and coal permeability when an appropriate productivity equation is selected. The field application of the proposed methods is demonstrated by analysis of production data of a horizontal CSG well in the Qinshui Basin, China.

scholarly journals EVALUATION OF AKPET GT9 GAS CONDENSATE RESERVOIR PERFORMANCE

2020 ◽  
Vol 1 (1) ◽  
pp. 1-13
Author(s):  
S. Okotie ◽  
N. O. Ogbarode
Keyword(s):  
Reservoir Characterization ◽  
Material Balance ◽  
Gas Condensate ◽  
Petroleum Engineering ◽  
Analysis Tool ◽  
Reservoir Performance ◽  
Future Production ◽  
Condensate Reservoir ◽  
Balance Analysis ◽  
Amount Of Knowledge

To effectively evaluate a gas condensate reservoir performance, the reservoir engineer must have a reasonable amount of knowledge about the reservoir to adequately analyze the reservoir performance and predict future production under various modes of operation. Due to the multiphase flow that exists in the reservoir, characterization of gas condensate reservoirs is often a difficult task with the variation of its overall composition in both space and time during production which complicates well deliverability analysis and the sizing of surface facilities. This study is primarily concern with the evaluation of a gas condensate reservoir performance of Akpet GT 9 Reservoir in the Niger Delta region of Nigeria with material balance analysis tool “MBal” without having to run numerical simulations. The result obtained with MBal on the analysis of Akpet GT 9 reservoir gave 23.934 Bscf of gas initially in place which compares favorably with the volume obtained from volumetric techniques. Results also shows that the most likely aquifer model is the Hurst–Van Everdingen - Dake radial aquifer and the reservoir is supported by a combined drive of water influx and fluid expansion. Okotie, S. | Department of Petroleum Engineering, Federal University of Petroleum Resources (FUPRE), Effurun, Delta State, Nigeria.

Productivity-Maximized Horizontal-Well Design With Multiple Acute-Angle Transverse Fractures

SPE Journal ◽  
2018 ◽  
Vol 23 (05) ◽  
pp. 1539-1551 ◽  
Author(s):  
Nadav Sorek ◽  
Jose A. Moreno ◽  
Ryan N. Rice ◽  
Guofan Luo ◽  
Christine Ehlig-Economides
Keyword(s):  
Horizontal Well ◽  
Acute Angle ◽  
Productivity Index ◽  
Hydraulic Fractures ◽  
Flow Area ◽  
Well Productivity ◽  
Fracture Angle ◽  
Fracture Length ◽  
Stress Direction ◽  
Minimum Stress

Summary Hydraulic fractures propagate perpendicular to the horizontal-well axis whenever the drilling direction is parallel to the minimum-principal-stress direction. However, operators frequently drill horizontal wells parallel to lease boundaries, resulting in hydraulic-fracture vertical planes slanted at angles less than 90° from the well axis. The stimulated-rock-volume (SRV) dimensions are defined by fracture height, well length, and fracture length multiplied by the sine of the angle between fracture planes and the horizontal-well axis (fracture angle). The well productivity index (PI) under boundary-dominated flow (BDF) is given by the PI for one fully penetrating fracture multiplied by the number of fractures. An extension of the unified-fracture-design (UFD) approach for rectangular drainage areas enables determination of the unique number of fractures that will maximize well productivity under BDF conditions given the formation permeability, proppant mass, fracture angle, and well spacing. Fracture length and width vary depending on the fracture angle, but the total-propped-fracture volume remains constant. Because the likely reason for drilling at an angle to the minimum-stress direction is to better cover a lease area with north/south and east/west boundaries, the smallest fracture angle will be 45°, corresponding to northwest/southeast or northeast/southwest minimum-stress direction. This results in the need to lengthen fractures by at most 40% to preserve the SRV for a given horizontal-well length and spacing. For the same sufficiently large proppant mass, this will reduce fracture conductivity by the same factor. However, because the flow area has increased, the result will be greater well productivity. This study shows a simple strategy for designing wells to maximize productivity even when not drilled in the minimum-stress direction.

A Holistic Study on Performance Evaluation of Horizontal Wells and its Implications on Tight Spacing Drilling Strategy in Mauddud Reservoir

2021 ◽  
Author(s):  
Lakshi Konwar ◽  
Bader Alhammadi ◽  
Ebrahim Alawainati ◽  
Ajithkumar Panicker
Keyword(s):  
Performance Evaluation ◽  
Future Development ◽  
Horizontal Well ◽  
Horizontal Wells ◽  
Productivity Index ◽  
Water Production ◽  
Vertical Wells ◽  
Productivity Improvement ◽  
Well Productivity ◽  
Improvement Factor

Abstract The objective of this paper is to present the comparative results of comprehensive analysis of horizontal well productivity and completion performance with vertical wells drilled and completed within same time window in the Mauddud reservoir in the Bahrain Oil Field. The study also focuses on performance evaluation of horizontal wells drilled in different areas of the field. Key reservoir risks and uncertainties associated with horizontal wells are identified, and contingency and mitigation plans are devised to address them. Besides controlling gas production, the benefits of using cemented horizontal wells over vertical wells are highlighted based on performance of recently completed workovers and economic evaluation. Reservoir and well performance are analyzed using a variety of analytical techniques such as well productivity index (PI), productivity improvement factor (PIF), normalized productivity improvement factor (PIFn), well productivity coefficient (Cwp), in conjunction with a statistical distribution function to reflect the average and most likely values. In addition, average oil/gas/water production, cumulative production, reserves, and estimated ultimate recovery (EUR) are compared for both vertical and horizontal wells using decline curve analysis. Furthermore, economics are evaluated for tight spacing drilling with vertical wells, as well as horizontal cemented wells, to optimize future development of Mauddud reservoir. Based on the evaluation, it is inferred that the average horizontal well outperforms a vertical well in terms of production rate, PI, PIF, reserves, and EUR in the field except in waterflood areas. Based on average cumulative oil, reserves and EUR, and well productivity coefficient, overall performance of horizontal wells are better in the GI area in comparison their counterparts in the North/South areas of the Mauddud reservoir, where the dominant mechanism is strong water drive. High gas and water production in horizontal wells are attributed to open-hole completions of the wells and the possibility of poor cementing. A trial has been completed recently in a few horizontal wells using cased-hole cemented completion with selected perforations, resulting in improved oil rates and the drastic reduction of gas to oil ratio. Furthermore, two new cased-hole cemented horizontal wells are planned in 2021 as a trial. A detailed cost-benefit analysis using a net present value concept is performed, leading to a rethink of future development strategies with a mix of both vertical as well as horizontal wells in the GI area. Using the dimensionless correlations and distribution functions, the productivity and PIF of new horizontal wells to be drilled in any area can be predicted during early prognosis given the values of average reservoir permeability, well length, and fluid properties. This study can be used as a benchmark for the development of a thin oil column with a large and expanding gas cap under crestal gas injection using both vertical and horizontal wells.

scholarly journals Productivity analysis for a horizontal well with multiple reorientation fractures in an anisotropic reservoir

2020 ◽  
Vol 75 ◽  
pp. 80
Author(s):  
Mingxian Wang ◽  
Zifei Fan ◽  
Lun Zhao ◽  
Guoqiang Xing ◽  
Wenqi Zhao ◽  
...  
Keyword(s):  
Horizontal Well ◽  
Productivity Index ◽  
Finite Conductivity ◽  
Productivity Analysis ◽  
Well Productivity ◽  
Fracture Conductivity ◽  
Fracture Angle ◽  
Fracture Spacing ◽  
Anisotropic Factor ◽  
Anisotropic Reservoir

Reorientation fractures may be formed in soft and shallow formations during fracturing stimulation and then affect well productivity. The principal focus of this study is on the productivity analysis for a horizontal well with multiple reorientation fractures in an anisotropic reservoir. Combining the nodal analysis technique and fracture-wing method, a semi-analytical model for a horizontal well with multiple finite-conductivity reorientation fractures was established to calculate its dimensionless productivity index and derivative for production evaluation. A classic case in the literature was selected to verify the accuracy of our semi-analytical solution and the verification indicates this new solution is reliable. Results show that for a fixed fracture configuration the dimensionless productivity index of the proposed model first goes up and then remains constant with the increase of fracture conductivity, and optimal fracture conductivity can be determined on derivative curves. Strong permeability anisotropy is a negative factor for well production and the productivity index gradually decreases with the increase of anisotropic factor. As principal fracture angle goes up, horizontal well’s productivity index increases correspondingly. However, the effect of reoriented fracture angle on the productivity index is not as strong as that of principal fracture angle. When reoriented fracture angle is smaller than principal fracture angle, reoriented factor should be as low as possible to achieve optimal productivity index. Meanwhile, well productivity index rises up with the increase of fracture number and fracture spacing, but the horizontal well has optimal reorientation fracture number and fracture spacing to get the economical productivity. Furthermore, the influence of the rotation of one central reorientation fracture on productivity index is weaker than that caused by the rotation of one external reorientation fracture. In addition, the asymmetrical distribution of one or more reorientation fractures slightly affects the productivity index when fracture conductivity is high enough.

Sign in / Sign up

Export Citation Format

Share Document