High Strength Coiled Tubing - How is Fatigue Life Affected by Slip Damage?

2020 ◽  
Author(s):  
Scott Sherman ◽  
Sean M Majko ◽  
Jeffrey Otto
Keyword(s):  
Fatigue Life ◽  
High Strength ◽  
Coiled Tubing

scholarly journals Fatigue Life Improvement of Cracked Aluminum 6061-T6 Plates Repaired by Composite Patches

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1421
Author(s):  
Armin Yousefi ◽  
Saman Jolaiy ◽  
Reza Hedayati ◽  
Ahmad Serjouei ◽  
Mahdi Bodaghi
Keyword(s):  
Fatigue Life ◽  
Fatigue Behavior ◽  
Weight Ratio ◽  
High Strength ◽  
Plastic Strain Amplitude ◽  
Composite Patch ◽  
Life Improvement ◽  
Cracked Structures ◽  
Aluminum Plates ◽  
High Flexibility

Bonded patches are widely used in several industry sectors for repairing damaged plates, cracks in metallic structures, and reinforcement of damaged structures. Composite patches have optimal properties such as high strength-to-weight ratio, easiness in being applied, and high flexibility. Due to recent rapid growth in the aerospace industry, analyses of adhesively bonded patches applicable to repairing cracked structures have become of great significance. In the present study, the fatigue behavior of the aluminum alloy, repaired by a double-sided glass/epoxy composite patch, is studied numerically. More specifically, the effect of applying a double-sided composite patch on the fatigue life improvement of a damaged aluminum 6061-T6 is analyzed. 3D finite element numerical modeling is performed to analyze the fatigue performance of both repaired and unrepaired aluminum plates using the Abaqus package. To determine the fatigue life of the aluminum 6061-T6 plate, first, the hysteresis loop is determined, and afterward, the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted and validated against the available experimental data from the literature. Results reveal that composite patches increase the fatigue life of cracked structures significantly, ranging from 55% to 100% for different applied stresses.

Influence of the pore morphology of high strength concrete on its fatigue life

2018 ◽  
Vol 112 ◽  
pp. 106-116 ◽  
Author(s):  
Miguel A. Vicente ◽  
Dorys C. González ◽  
Jesús Mínguez ◽  
Manuel A. Tarifa ◽  
Gonzalo Ruiz ◽  
...  
Keyword(s):  
Fatigue Life ◽  
High Strength Concrete ◽  
High Strength ◽  
Pore Morphology ◽  
Strength Concrete

scholarly journals Multiaxial fatigue study on steel transversal attachments under constant amplitude proportional and non-proportional loadings

2018 ◽  
Vol 165 ◽  
pp. 16007
Author(s):  
Martin Garcia ◽  
Claudio A. Pereira Baptista ◽  
Alain Nussbaumer
Keyword(s):  
Fatigue Life ◽  
High Strength ◽  
Fatigue Tests ◽  
Multiaxial Fatigue ◽  
Life Assessment ◽  
Experimental Program ◽  
Proportional Loading ◽  
Load Carrying ◽  
Stress States ◽  
Experimental Values

In this study, the multiaxial fatigue strength of full-scale transversal attachment is assessed and compared to original experimental results and others found in the literature. Mild strength S235JR steel is used and an exploratory investigation on the use of high strength S690QL steel and the effect of non-proportional loading is presented. The study focuses on non-load carrying fillet welds as commonly used in bridge design and more generally between main girders and struts. The experimental program includes 33 uniaxial and multiaxial fatigue tests and was partially carried out on a new multiaxial setup that allows proportional and non-proportional tests in a typical welded detail. The fatigue life is then compared with estimations obtained from local approaches with the help of 3D finite element models. The multiaxial fatigue life assessment with some of the well-known local approaches is shown to be suited to the analysis under multiaxial stress states. The accuracy of each models and approaches is compared to the experimental values considering all the previously cited parameters.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Low-cycle fatigue behaviour of laser welded high-strength steel DOMEX 700 MC

2018 ◽  
Vol 157 ◽  
pp. 05013 ◽  
Author(s):  
Peter Kopas ◽  
Milan Sága ◽  
František Nový ◽  
Bohuš Leitner
Keyword(s):  
Fatigue Life ◽  
Welded Joints ◽  
High Strength Steel ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
High Strength ◽  
Fatigue Behaviour ◽  
Total Strain Amplitude ◽  
Cycle Fatigue ◽  
Fatigue Life Analysis

The article presents the results of research on low cycle fatigue strength of laser welded joints vs. non-welded material of high-strength steel DOMEX 700 MC. The tests were performed under load controlled using the total strain amplitude ɛac. The operating principle of the special electro-mechanic fatigue testing equipment with a suitable clamping system was working on 35 Hz frequency. Fatigue life analysis was conducted based on the Manson-Coffin-Basquin equation, which made it possible to determine fatigue parameters. Studies have shown differences in the fatigue life of original specimens and laser welded joints analysed, where laser welded joints showed lower fatigue resistance. In this article a numerical analysis of stresses generated in bending fatigue specimens has been performed employing the commercially available FEM-program ADINA.

Development of a High Strength Mg-Zn-Y-Zr Wrought Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 1701-1706
Author(s):  
Rong Shi Chen ◽  
Wei Neng Tang ◽  
Dao Kui Xu ◽  
En Hou Han
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Fatigue Life ◽  
Deformation Behavior ◽  
Fatigue Behavior ◽  
High Strength ◽  
Zn Content ◽  
High Fatigue ◽  
Content Range ◽  
Zr Alloy

The effects of Y addition to the Mg-Zn-Y-Zr alloy on the change of the microstructure and the mechanical properties (with the Y content range of 1 to 3 wt%) have been investigated. It shows that when Zn content is constant (5.65wt%), the alloys with Y content between 1.17 and 1.72wt% nearly reach its highest strength. With the composition near the optimums, the extruded Mg-6%Zn-1%Y-Zr alloy shows high strength and excellent ductility. The deformation behavior of this new alloy at high temperature has also been studied. Moreover, the super-long fatigue behavior of the Mg-6%Zn-1%Y-Zr alloy has also been tested, the results show the alloy with a high fatigue strength of about 85-90MPa in the super-long fatigue life regime of 1×109 cycles.

scholarly journals Experimental Investigation on the Effect of Shot Peening and Deep Rolling on the Fatigue Response of High Strength Fasteners

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1093 ◽  
Author(s):  
Reggiani
Keyword(s):  
Fatigue Life ◽  
Shot Peening ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Tests ◽  
Published Data ◽  
Deep Rolling ◽  
Beneficial Impact ◽  
The Impact ◽  
Fatigue Life Enhancement

Shot-peening and deep rolling are mechanical surface treatments that are commonly applied to enhance the fatigue performances of components, owing to their capacity to generate compressive residual stresses and induce work hardening. However, literature is still poor of published data concerning the application of these treatments to high strength steels fasteners, although these represent a class of components among the most widespread. In the present work, the impact of deep rolling and shot-peening performed in the underhead radius of two set of fasteners made of 36NiCrMo and 42CrMoV for fatigue life enhancement has been investigated. The experimental tests consisted of six combinations of shot-peening and deep rolling, including the non-treated state. Two test campaigns have been sequentially carried out with different process parameters and treatment sequences. The results always showed a beneficial impact of the deep rolling on fatigue, especially for the 42CrMoV steel. Conversely, the effect of the shot-peening strongly depended on the selected set of parameters, alternatively leading to an improvement or a worsening of the fatigue life in relation to the level of induced surface roughness.

scholarly journals High-Strength Reinforcing Steel Bars: Low Cycle Fatigue Behavior Using RGB Methodology

2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Jorge E. Egger ◽  
Fabian R. Rojas ◽  
Leonardo M. Massone
Keyword(s):  
Fatigue Life ◽  
Strain Amplitude ◽  
Low Cycle Fatigue ◽  
High Strength ◽  
Image Correlation ◽  
Total Strain ◽  
Total Strain Amplitude ◽  
Reinforcing Steel ◽  
Cycle Fatigue ◽  
Steel Bars

AbstractLow cycle fatigue life of high-strength reinforcing steel bars (ASTM A706 Grade 80), using photogrammetry by RGB methodology is evaluated. Fatigue tests are performed on specimens under constant axial displacement with total strain amplitudes ranging from 0.01 to 0.05. The experimental observations indicate that buckling of high-strength reinforcing bars results in a damaging degradation of their fatigue life performance as the slenderness ratio increases, including an early rebar failure as the total strain amplitude increases since it achieves the plastic range faster. In addition to this, the results show that the ratio of the ultimate tensile strength to yield strength satisfies the minimum of 1.25 specified in ASTM A706 for reinforcement. On the other hand, the RGB methodology indicates that the axial strains measured by photogrammetry provide more accurate data since the registered results by the traditional experimental setup do not detect second-order effects, such as slippage or lengthening of the specimens within the clamps. Moreover, the RGB filter is faster than digital image correlation (DIC) because the RGB methodology requires a fewer computational cost than DIC algorithms. The RGB methodology allows to reduce the total strain amplitude up to 45% compared to the results obtained by the traditional setup. Finally, models relating total strain amplitude with half-cycles to failure and total strain amplitude with total energy dissipated for multiple slenderness ratios (L/d of 5, 10, and 15) are obtained.

Sign in / Sign up

Export Citation Format

Share Document