Well Performance Calculations for Artificial Lift Screening

Author(s):  
P. A. Kefford ◽  
M. Gaurav
2021 ◽  
Author(s):  
Nigel Ramkhalawan ◽  
Hamid Hassanali

Abstract Frequent rod failures still occur in Progressive Cavity Pumped (PCP) wells with high dog-leg severities although they are fitted with adequate rod centralization. This results in well downtime and production deferrals. Offshore workovers are expensive and significantly affect operating cost (OPEX) of the operator. This study sought to evaluate the potential benefits of Electrica l Submersible Progressive Cavity Pumps (ESPCP) as an economic alternative for highly deviated wells in the offshore field in Trinidad. In this theoretical study, a screening criterion was established and four (4) candidates, all produced by surface driven PCPs, were selected. Models of ESPCP systems were developed using industry standard Progressive Cavity Pump software, parameters from the original PCP models as well as actual field well tests and production data. An economic evaluation, which integrated oil price and production rate sensitivities, was conducted using field data, including field reservoir characteristics and past well performance. The ESPCP model results suggest a cumulative increase of 567 BOPD is expected for all four wells. Using an oil price of US $45 per barrel, the analysis was conducted on all wells targeted for ESPCP conversion. Assuming a P50 oil rate, sensitivities were run to establish the minimum oil price for the project to be economically feasible. The operator's project economic success criteria were :(1) pay-out period of <2 years and (2) NPV of > US $0.15 Million considering a ten (10) year project. An integrated sensitivity analysis was performed for the entire project with varying expected production increases and fluctuating global oil prices. The simulations identified that the project will be uneconomic at a global oil price of US $20/bbl. Assuming a project life of 10 years and based on the expected production increase, the project is massively profitable, yielding an expected NPV of US $9.3 Million at US $45 per barrel with expected pay-out times between 0.63-1.8 years with investment of US $4 Million. Additional benefits anticipated include, increased well uptime and the corresponding reduction in workover costs. Another opportunity that results from the conversion to ESPCP, is the possibility of lowering the pump in the wellbore, thereby increasing the well producing life and increasing the recoverable reserves. Installation of ESPCPs, in theory, can be an economic success in an area where surface driven PCP experiences repetitive rod failures, leading to production deferrals and workover. Additionally, lowering the pump in the wellbore may be possible, thereby increasing the well producing life and increasing recoverable reserves which would not have been possible using traditional artificial lift methods.


2015 ◽  
Author(s):  
Guilherme Hartenbach ◽  
João Magalhães ◽  
Yngve Belsvik ◽  
Rui Pessoa ◽  
Daniel Lemos

2020 ◽  
Vol 17 (3) ◽  
pp. 150-155
Author(s):  
Tega Odjugo ◽  
Yahaya Baba ◽  
Aliyu Aliyu ◽  
Ndubuisi Okereke ◽  
Lekan Oloyede ◽  
...  

Hydrocarbon exploration basically requires effective drilling and efficient overpowering of frictional and viscosity forces. Normally, frictional power losses occur in deep well systems and it is essential to analyse each component of any well system to determine where exactly pressure is lost, and this can be done using Nodal Analysis. In this study, nodal analysis has been carried out with the use of PROSPER, a software for well performance, design and optimisation. Artificial lifts can then be used to solve the problem of frictional power losses. To increase the production of Barbra 1 well in the Niger Delta and hence extend its functional life, we have applied nodal analysis. Modelling results for three artificial lift methods; continuous gas lift, intermittent gas lift and electrical submersible pump were found to be 1734.93 bbl/day, 451.50 bbl/day and 2869 bbl/day respectively. The output from the well performance without artificial lift was 1370.99 bbl/day by applying Darcy’s model. Meanwhile, the output from the well without artificial lift is 89.90 bbl/day when aided with productivity index (PI) entry, the normal model for intermittent gas lift. Hence, from the comparative analysis of the results obtained from this study, it was deduced that when artificial lifts are employed, the well output increases significantly from 1370.99bbl/day to 2869 bbl/day (electrical submersible pump). This study concludes that wells such as Barbra 1 are good candidates for artificial lift, and this is evidenced by increasing productivity. Keywords: Production optimisation, nodal analysis, prosper simulator and barbra well.


2018 ◽  
Vol 7 (2) ◽  
pp. 46-54
Author(s):  
Fitrianti Fitrianti ◽  
Dike Fitriansyah Putra ◽  
Desma Cendra

The declining reservoir, oil production and pressure depletion with the well being produced, the results of the investment of the well will also decrease. For that there needs to be energy that can help to lift the fluid to the surface. One of the artificial lift methods that can be used is a gas lift. Gas lift is a method commonly used when there is a natural gas source as an injection gas supply. The selection of the artificial lift method is based on several considerations, namely the reservoir conditions, fluid conditions, well conditions, conditions on the surface, availability of electricity, availability of gas, and sand problem. The influential parameters in the selection of gas lifts include: Productivity Index (PI), Gas Liquid Ratio (GLR), depth of the well and driving mechanism from the reservoir. The Gas Lift that the production optimization wants to do is the injection system in a Continuous Gas Lift. Used in wells that have a high Productifity Index value. Where in the LB field to be analyzed, the Productifity Index value is 2.0 bpd / psi. This study intends to optimize a gaslift well performance as an effort to maximize the results of well production. Based on the research that has been done using Prosper Modeling on the “J” field, the following conclusions are obtained the effect of pressure and viscosity on the gas lift well flow rate in this condition can be said to be efficient, because the conditions / pressure given at temperatures below 300 F can reach the miscible condition and from the results of determining the optimal conditions to get the best well performance, obtain an optimal liquid rate of 1829.4 STB / D with an oil rate of 36.6 STB / D.   Keywords: Gas lift, Optimization, Immiscible Pressure, Viscosity


2015 ◽  
Author(s):  
Amro Hassan ◽  
Ahmed Abd ElMeguid ◽  
Arshad Waheed ◽  
Mohamed Salah ◽  
Essam Abd ElKarim

Abstract The Baharyia formation is a common reservoir in the Western Desert of Egypt. It is characterized as a heterogeneous reservoir with low sand quality. It is comprised of fine-grained sandstone, thin, laminated, sand-poor parasequences with shale interbeds. The heterogeneity and low permeability of the Upper Baharyia reservoirs are the primary challenges to maintaining economic well productivity. The interest in developing low permeability reservoirs stems from favorable economics attributed to advancements in horizontal well drilling and hydraulic fracturing technology, offering methods to increase production by increasing the contact area of the producing interval. Subsequently, it became apparent that wellbore contact alone was not always sufficient for providing production increases expected, thus requiring multistage hydraulic fracturing (MSHF) stimulation treatments to achieve production targets. Primary well production analysis revealed that the cumulative production from the horizontal well discussed was enhanced from 37 to 70% of recoverable reserve and the recovery factor was doubled. From a production analogy standpoint, these resulted in reduced drilling of three vertical wells and had direct economic benefits by reducing the installed artificial lift strings, related expensive artificial lift equipment repairs, and the number of necessary workovers. This paper takes a multidisciplinary approach to help understand productivity enhancement of low permeability reservoirs in the Western Desert of Egypt, through a detailed analysis of well performance and successful implementation of MSHF in horizontal wells to maximize drainage volume around the well. It is intended to serve as guidelines to help operators facing similar challenges.


2021 ◽  
Author(s):  
Simon Paul ◽  
Gerard Dukhoo ◽  
Murchison Phillip ◽  
Jediael Persadsingh

Abstract In Trinidad's mature onshore oilfields, operators have traditionally forecasted the initial production rates back calculated from decline models. These rates, then reduced annually by a predetermined decline model has been used to evaluate financial feasibility. This method does not make use of the reservoir pressure. This paper demonstrates how software modelling, utilizing the reservoir pressure can reasonably forecast the performance of low rate oil producers and alert the operator of the need for artificial lift from the inception of the production cycle. The objectives of the project were to determine remaining recoverable reserves, evaluate the potential for redevelopment (workovers and infill drilling) and to demonstrate that software modeling can be used to forecast production for an oil reservoir in a mature onshore oilfield in Southern Trinidad. Petroleum Experts Integrated Production Modeling (IPM) software suite was used for building all models. A comparison of the production forecasted by software modelling and the traditional method of forecasting initial production rates by back calculating from decline models was also undertaken. Using the available data and net oilsand maps, the fault block bulk volumes, oil in place and the remaining reserves were determined. These results were then used to identify fault blocks with potential workover well candidates and infill well locations. Research of well files and well logs were used in evaluating zones for potential recompletions, reperforation or perforation of additional footage for production. Forecasting and comparison of the initial production rates and ultimate cumulative production for the proposed infill wells and recompletions using the traditional IP/Decline model method and computer modeling was then performed. Form the data available, it was determined there were four blocks with remaining reserves that could be successfully recovered. The recovery methods proposed included the workover of two existing wells and drilling of two infill wells. Initial production rates and ultimate production volumes obtained by modeling of workover and new well performance had reasonably close agreement with those obtained by the traditional IP/Decline models. The results of the modeling, however indicated that all the wells required the use of pumping mechanisms (sucker rod/beam pumps) to sustain production over a ten-year period. The need for this important production mechanism would not have been realized from the IP/Decline method. An important distinction is that the modelling makes direct use of the reservoir pressure, whereas the IP/Decline model does not.


2013 ◽  
Author(s):  
Roberto Suarez-Rivera ◽  
Jeff Burghardt ◽  
Sergei Stanchits ◽  
Eric Edelman ◽  
Aniket Surdi

Sign in / Sign up

Export Citation Format

Share Document