Reduced Water Production and Increased Oil Production Using Smart Completions and MPFM "Case Study"

2007 ◽  
Author(s):  
Mohammad S. Al-Shenqiti ◽  
Alaa A. Dashash ◽  
Ibrahim H. Al-Arnaout ◽  
Saad M. Al-Driweesh ◽  
Zaki Bakhteyar
Keyword(s):  
Oil Production ◽  
Water Production ◽  
Reduced Water

New Gel Aggregates To Improve Sweep Efficiency During Waterflooding

2011 ◽  
Vol 14 (01) ◽  
pp. 120-128 ◽  
Author(s):  
Guanglun Lei ◽  
Lingling Li ◽  
Hisham A. Nasr-El-Din
Keyword(s):  
Low Cost ◽  
Oil Production ◽  
High Water ◽  
Resistance Factor ◽  
Water Production ◽  
Sweep Efficiency ◽  
Low Viscosity ◽  
Productivity Decline ◽  
High Water Cut ◽  
Water Cut

Summary A common problem for oil production is excessive water production, which can lead to rapid productivity decline and significant increases in operating costs. The result is often a premature shut-in of wells because production has become uneconomical. In water injectors, the injection profiles are uneven and, as a result, large amounts of oil are left behind the water front. Many chemical systems have been used to control water production and improve recovery from reservoirs with high water cut. Inorganic gels have low viscosity and can be pumped using typical field mixing and injection equipment. Polymer or crosslinked gels, especially polyacrylamide-based systems, are mainly used because of their relatively low cost and their supposed selectivity. In this paper, microspheres (5–30 μm) were synthesized using acrylamide monomers crosslinked with an organic crosslinker. They can be suspended in water and can be pumped in sandstone formations. They can plug some of the pore throats and, thus, force injected water to change its direction and increase the sweep efficiency. A high-pressure/high-temperature (HP/HT) rheometer was used to measure G (elastic modulus) and G" (viscous modulus) of these aggregates. Experimental results indicate that these microspheres are stable in solutions with 20,000 ppm NaCl at 175°F. They can expand up to five times their original size in deionized water and show good elasticity. The results of sandpack tests show that the microspheres can flow through cores with permeability greater than 500 md and can increase the resistance factor by eight to 25 times and the residual resistance factor by nine times. The addition of microspheres to polymer solutions increased the resistance factor beyond that obtained with the polymer solution alone. Field data using microspheres showed significant improvements in the injection profile and enhancements in oil production.

Evaluation of CO2 Gas Injection For Major Oil Production Fields in Malaysia - Experimental Approach Case Study: Dulang Field

2001 ◽  
Author(s):  
Zahidah Md. Zain ◽  
Nor Idah Kechut ◽  
Ganesan Nadeson ◽  
Noraini Ahmad ◽  
D.M. Anwar Raja
Keyword(s):  
Experimental Approach ◽  
Gas Injection ◽  
Oil Production ◽  
Co2 Gas

Undersaturated Hydrocarbon Reservoir Waterflooding: A simulation Approach to Performance Assessment

2021 ◽  
Author(s):  
Adekunle Tirimisiyu Adeniyi ◽  
Miracle Imwonsa Osatemple ◽  
Abdulwahab Giwa
Keyword(s):  
Oil Recovery ◽  
Net Present Value ◽  
Oil Production ◽  
Base Case ◽  
Present Value ◽  
Sweep Efficiency ◽  
Recovery Method ◽  
Solution Approach ◽  
Hydrocarbon Reservoir

Abstract There are a good numbers of brown hydrocarbon reservoirs, with a substantial amount of bypassed oil. These reservoirs are said to be brown, because a huge chunk of its recoverable oil have been produced. Since a significant number of prominent oil fields are matured and the number of new discoveries is declining, it is imperative to assess performances of waterflooding in such reservoirs; taking an undersaturated reservoir as a case study. It should be recalled that Waterflooding is widely accepted and used as a means of secondary oil recovery method, sometimes after depletion of primary energy sources. The effects of permeability distribution on flood performances is of concerns in this study. The presence of high permeability streaks could lead to an early water breakthrough at the producers, thus reducing the sweep efficiency in the field. A solution approach adopted in this study was reserve water injection. A reverse approach because, a producing well is converted to water injector while water injector well is converted to oil producing well. This optimization method was applied to a waterflood process carried out on a reservoir field developed by a two - spot recovery design in the Niger Delta area of Nigeria that is being used as a case study. Simulation runs were carried out with a commercial reservoir oil simulator. The result showed an increase in oil production with a significant reduction in water-cut. The Net Present Value, NPV, of the project was re-evaluated with present oil production. The results of the waterflood optimization revealed that an increase in the net present value of up to 20% and an increase in cumulative production of up to 27% from the base case was achieved. The cost of produced water treatment for re-injection and rated higher water pump had little impact on the overall project economy. Therefore, it can conclude that changes in well status in wells status in an heterogenous hydrocarbon reservoir will increase oil production.

scholarly journals Comparison Between Homogenous and Heterogeneous Reservoirs: A Parametric Study of Water Coning Phenomena

2021 ◽  
Vol 5 (1) ◽  
pp. 119-131
Author(s):  
Frzan F. Ali ◽  
Maha R. Hamoudi ◽  
Akram H. Abdul Wahab
Keyword(s):  
Production Rate ◽  
Oil Production ◽  
Water Production ◽  
Effective Parameters ◽  
Radial Cross Section ◽  
Heterogeneous Reservoirs ◽  
Water Breakthrough ◽  
Water Coning ◽  
Water Cut ◽  
Reservoir Simulator

Water coning is the biggest production problem mechanism in Middle East oil fields, especially in the Kurdistan Region of Iraq. When water production starts to increase, the costs of operations increase. Water production from the coning phenomena results in a reduction in recovery factor from the reservoir. Understanding the key factors impacting this problem can lead to the implementation of efficient methods to prevent and mitigate water coning. The rate of success of any method relies mainly on the ability to identify the mechanism causing the water coning. This is because several reservoir parameters can affect water coning in both homogenous and heterogeneous reservoirs. The objective of this research is to identify the parameters contributing to water coning in both homogenous and heterogeneous reservoirs. A simulation model was created to demonstrate water coning in a single- vertical well in a radial cross-section model in a commercial reservoir simulator. The sensitivity analysis was conducted on a variety of properties separately for both homogenous and heterogeneous reservoirs. The results were categorized by time to water breakthrough, oil production rate and water oil ratio. The results of the simulation work led to a number of conclusions. Firstly, production rate, perforation interval thickness and perforation depth are the most effective parameters on water coning. Secondly, time of water breakthrough is not an adequate indicator on the economic performance of the well, as the water cut is also important. Thirdly, natural fractures have significant contribution on water coning, which leads to less oil production at the end of production time when compared to a conventional reservoir with similar properties.

Tubing Straddle System to Restores Oil Production Using Digital Slickline Conveyance A Case Study

2020 ◽  
Author(s):  
Syed Zubair Gilani ◽  
Wuroud Mohammed Alfadhli ◽  
Ravi Kurma ◽  
Yousef Al-Mansour ◽  
Mousa Al-Sulaili ◽  
...  
Keyword(s):  
Oil Production
Sign in / Sign up

Export Citation Format

Share Document