Miscible Gas Injection Piloting and Modeling in a Giant Carbonate Reservoir

Author(s):  
Masoud Haajizadeh ◽  
Hafez H. Hafez ◽  
Rasheed Al Hassan ◽  
Abdulla Bakheet Al Katheeri ◽  
Muhamad Nepolian Ghozali ◽  
...  
2015 ◽  
Author(s):  
Abolfazl Hashemi ◽  
Bahram Miri ◽  
Reza Chegeni ◽  
Fatemeh Namdarian ◽  
Morteza Aghababee Taghanaki ◽  
...  

2021 ◽  
Author(s):  
Alfredo Freites ◽  
Victor Segura ◽  
Muhammad Muneeb

Abstract Maximum Reservoir Contact wells (MRCs) are a potential alternative to reduce the number of wells required to develop hydrocarbon reservoirs, improve sweeping efficiency and delay gas and water breakthrough. The well completions design is critical for the success of MRCs. In this study we present a case study of a MRC well completion design using Limited Entry Liners (LEL) in a mature carbonate reservoir under water and miscible gas injection. We developed an integrated workflow that considered a high-resolution numerical simulation model calibrated to static and dynamic data and wellbore-reservoir models coupling, for capturing the details of the flow interaction between both systems. Flow restrictions in the form of additional pressure drops to the flow from the reservoir into the wellbore were used to simulate the effect of small open flow areas, i.e.shot densities, in the LELs. Our work allowed identifying the most likely entry points of gas and water and design the well to minimize their impact on oil production. We observe that longer lengths open to flow outweighs the detrimental effect of producing from intervals closer to the water saturated zones. We also observed that balancing the inflow profile along the wellbore did not report beneficial results to oil production as it stimulates production from the reservoir zone from which the gas breakthrough is expected (middle of the producing section); this result is particularly relevant as it shows that designing the well completions with base only on static data could lead to poor production performance. The suggested completion for the MRC well encompasses four segments; a segment covering almost 50 % of the well length and located at the middle of the producing section with a blind liner (close to flow for gas control) and the remaining three with slotted liners with enough open area as to avoid causing significant pressure drops.


2021 ◽  
Author(s):  
Valentina Zharko ◽  
Dmitriy Burdakov

Abstract The paper presents the results of a pilot project implementing WAG injection at the oilfield with carbonate reservoir, characterized by low efficiency of traditional waterflooding. The objective of the pilot project was to evaluate the efficiency of this enhanced oil recovery method for conditions of the specific oil field. For the initial introduction of WAG, an area of the reservoir with minimal potential risks has been identified. During the test injections of water and gas, production parameters were monitored, including the oil production rates of the reacting wells and the water and gas injection rates of injection wells, the change in the density and composition of the produced fluids. With first positive results, the pilot area of the reservoir was expanded. In accordance with the responses of the producing wells to the injection of displacing agents, the injection rates were adjusted, and the production intensified, with the aim of maximizing the effect of WAG. The results obtained in practice were reproduced in the simulation model sector in order to obtain a project curve characterizing an increase in oil recovery due to water-alternating gas injection. Practical results obtained during pilot testing of the technology show that the injection of gas and water alternately can reduce the water cut of the reacting wells and increase overall oil production, providing more efficient displacement compared to traditional waterflooding. The use of WAG after the waterflooding provides an increase in oil recovery and a decrease in residual oil saturation. The water cut of the produced liquid decreased from 98% to 80%, an increase in oil production rate of 100 tons/day was obtained. The increase in the oil recovery factor is estimated at approximately 7.5% at gas injection of 1.5 hydrocarbon pore volumes. Based on the received results, the displacement characteristic was constructed. Methods for monitoring the effectiveness of WAG have been determined, and studies are planned to be carried out when designing a full-scale WAG project at the field. This project is the first pilot project in Russia implementing WAG injection in a field with a carbonate reservoir. During the pilot project, the technical feasibility of implementing this EOR method was confirmed, as well as its efficiency in terms of increasing the oil recovery factor for the conditions of the carbonate reservoir of Eastern Siberia, characterized by high water cut and low values of oil displacement coefficients during waterflooding.


2014 ◽  
Author(s):  
M. Cobanoglu ◽  
A. Jabri ◽  
F. Mahruqi ◽  
O. Quintero Sarmiento ◽  
S. Linthorst

2005 ◽  
Author(s):  
Gary F. Teletzke ◽  
Prateek Dinesh Patel ◽  
Amy Chen

2021 ◽  
Author(s):  
Siqing Xu ◽  
Ahmed A BinAmro ◽  
Aaesha K. Al Keebali ◽  
Mohamed Baslaib ◽  
Shehadeh Masalmeh

Abstract Miscible CO2 flood is a well-established proven EOR recovery mechanism. There have been a large number of CO2 EOR developments worldwide, in both carbonate and clastic reservoirs. Potential control or influence factors on incremental production and incremental recovery over water flood are well documented in the published literature. Some of the published CO2 EOR developments have reported relatively high incremental recoveries. ADNOC is a leader in miscible gas injection EOR in carbonate reservoirs. There are a number of ongoing miscible gas injection EOR developments within its portfolio contributing a significant amount of production. Miscible CO2 flood is a key EOR development for ADNOC. Following intensive screening studies and laboratory experiments, the first CO2 EOR pilot in the MENA region was conducted as early as 2009 in one of ADNOC Onshore fields. This paved the way for further large-scale deployment and CO2 WAG pilots starting in 2016, both onshore. Appreciable progresses have been made since 2009. This bodes well with the significant initiatives undertaken by the UAE towards carbon emissions and greenhouse gas reduction, climate control and sustainable development. There are broad consensus that climate changes are now and will continue to affect all countries on all continents. Potential global warming can disrupt national economies and adversely impact on lives, costing people, communities and countries already today and perhaps more in the future. Carbon Capture, Utilization, and Storage (CCUS) technologies have been making headlines and attracting increasing amount of renewed attention, because they are in line with meeting global greenhouse gas reduction goals, and contributing towards climate control and sustainable development. The giant Abu Dhabi onshore field consists of 6 carbonate reservoirs. Several pilots, immiscible hydrocarbon gas injection and CO2 WAG, and a pattern immiscible gas injection WAG flood have been executed. Miscible gas injection EOR is therefore field proven. However, due to large field size, surface congestion constraints, geological and fluid variations, miscible gas injection EOR development by reservoir individually becomes complex and economically challenging. This paper presents a comprehensive study and recommends an integrated CCUS Hub development approach - enabling field-wide EOR development with several hundred million-barrels of incremental recovery. The study follows a step-by-step systematic method. Existing water flood performances were assessed first. History matched full field simulation then leads to identification of CO2 EOR targets by area/flank for each reservoir. These are referred to as sweet development areas. Available advanced PVT data were analysed and a multi-reservoir single equation of state developed. It has been found that only CO2 is miscible across all six reservoirs, while hydrocarbon gas is also miscible for the deepest two reservoirs. Dedicated fine scale sector models (EOR history matched where applicable) were developed to generate multiple CO2 EOR development scenarios, for example, depending on water flood maturity at the time of CO2 EOR start-up, and potential impact on incremental oil production, incremental oil recovery due to reservoir heterogeneity. First results from sector modelling show that quite a few areas/flanks would be sub-economical if CO2 EOR development on a stand-alone basis. Hence the concept of a CCUS Hub is proposed, which would allow sweet development areas in any or all of the six reservoirs to be developed from a single common surface Cluster. There is potential space for development phasing, allowing additional CO2 EOR developments within the same cluster area once ullage and CO2 supply becomes available. The CCUS Hub development approach facilitates optimization and sharing of injection/production flow-lines; surface space, gathering and processing facilities, CO2 supply, CO2 recovery unit deployment coupled with produced gas re-injection into the 2 deepest reservoirs. Compared to a more conventional development approach of reservoir by reservoir, considerable scope for CAPEX and OPEX savings was found. Assuming a constant future oil price, a reduction in development costs would allow more sweet development areas to pass the threshold of economical development, leading to an increase in overall incremental production and recovery from CO2 EOR.


Sign in / Sign up

Export Citation Format

Share Document