scholarly journals The effect of surfactants on the performances of ceramic slurry by material extrusion and photo-polymerization combined molding process

2021 ◽  
Vol 129 (8) ◽  
pp. 489-495
Author(s):  
Xin HE ◽  
Jie XU ◽  
Weixi JI
Keyword(s):  
Molding Process ◽  
Material Extrusion ◽  
Photo Polymerization ◽  
Ceramic Slurry

Filling Behavior of Polymer Material into Sub-^|^mu;m Structure in Injection Molding Process

2013 ◽  
Vol 133 (4) ◽  
pp. 105-111
Author(s):  
Chisato Yoshimura ◽  
Hiroyuki Hosokawa ◽  
Koji Shimojima ◽  
Fumihiro Itoigawa
Keyword(s):  
Injection Molding ◽  
Polymer Material ◽  
Injection Molding Process ◽  
Molding Process

Pengembangan Mesin Pencacah Sampah/Limbah Plastik Dengan Sistem Crusher dan Silinder Pemotong Tipe Reel

2015 ◽  
Vol 10 (2) ◽  
pp. 66
Author(s):  
Junaidi - ◽  
Ichlas Nur ◽  
Nofriadi - ◽  
Rusmardi -
Keyword(s):  
Testing Machine ◽  
Engine Performance ◽  
Performance Testing ◽  
Injection Molding Process ◽  
Molding Process ◽  
Recycling Industry ◽  
Performance Improvements ◽  
Plastic Recycling ◽  
Technical Evaluation ◽  
Lower Frame

Waste plastic mounting, but can be recycled into other products in the form of granules before further processed into pellets and seed injection molding process produces products such as buckets, plates, bottles and other beverages. To be processed into the required form of granules of plastic thrasher. Though so small plastic recycling industry is still constrained in plastic enumeration process because the machine used was not optimal ability. The purpose of this research is the development of the system thrasher plastic crusher and cutter cylinder-type reel and technical evaluation. This study was conducted over two years, the first year the design and manufacture of machinery, the second year is a technical evaluation of the engine, engine performance improvements and economic analysis of granular plastic products.From the results obtained engine design capacity of the machine ± 350 kg / h, the engine size is 50 cm x 120 cm x 30 cm, power motor of 10 HP at 1450 RPM rotation with 3 phase. Some of the major components of the engine that is, counter crusher unit consists of two counter rotating cylinders opposite, counter shaft size Ø 4 cm x 58 cm, blade chopper Ø 17 cm x 2 cm with the number of teeth / blades 7 pieces and the number of blades along shaft 7 pieces, buses retaining Ø 10 cm x 2 cm. Counter-cylinder unit consists of a reel-type cutter counter shaft size Ø 4 cm x 90 cm, the middle shaft mounted cylinder with Ø 17 cm x 40 cm as the holder of the chopper blades. Chopper blade consists of 4 pieces with a size of 40 cm x 2 cm x 4 cm with ASSAB materials. Furthermore, as the blade retaining bedknife shear force of the blade chopper, upper frame, lower frame, strainer, funnel entry, exit funnel, and the drive unit consists of an electric motor, reducer, belts, pulleys and 2 pieces of gear transmission. The results of performance testing machine crusher round cylinder 75 RPM and 1450 RPM reel-type cutting machine capacity ± 300 kg / h on the filter hole Ø 1.5 cm, with a 80% grain uniformity.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

scholarly journals Patterned waveguide liquid crystal displays

RSC Advances ◽  
2020 ◽  
Vol 10 (68) ◽  
pp. 41693-41702
Author(s):  
Yunho Shin ◽  
Jinghua Jiang ◽  
Guangkui Qin ◽  
Qian Wang ◽  
Ziyuan Zhou ◽  
...  
Keyword(s):  
Liquid Crystal ◽  
Switching Time ◽  
Contrast Ratio ◽  
Liquid Crystal Displays ◽  
High Contrast ◽  
High Brightness ◽  
Photo Polymerization ◽  
Ultrafast Switching ◽  
Light Waveguide ◽  
Polymer Stabilized

A polymer stabilized LC based light waveguide display is reported. Performance is improved by patterned photo-polymerization or electrode. It has high brightness, ultrafast switching time, high contrast ratio, and high transmittance for transparent and augmented displays.

Sign in / Sign up

Export Citation Format

Share Document