scholarly journals Effect of Whisker Diameter on Mechanical Properties, Oxidation Resistance and Cutting Performance of Titanium Carbide Whisker/Alumina Composites

1996 ◽  
Vol 104 (1213) ◽  
pp. 892-896
Author(s):  
Nobuyuki TAMARI ◽  
Isao KONDOH ◽  
Takahiro TANAKA ◽  
Nobuyuki TOKUNAGA ◽  
Kazuhiro TEZUKA ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Oxidation Resistance ◽  
Cutting Performance ◽  
Alumina Composites ◽  
Whisker Diameter

scholarly journals Mechanical Properties and Cutting Performance of Titanium Carbide Whisker/Alumina Composites

1996 ◽  
Vol 104 (1209) ◽  
pp. 439-443 ◽  
Author(s):  
Nobuyuki TAMARI ◽  
Takahiro TANAKA ◽  
Isao KONDOH ◽  
Kazuhiro TEZUKA ◽  
Tsutomu YAMAMOTO
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Cutting Performance ◽  
Alumina Composites

scholarly journals Sintering and Mechanical Properties of Titanium Carbide Whisker/Alumina Composites

1995 ◽  
Vol 103 (1197) ◽  
pp. 506-510 ◽  
Author(s):  
Nobuyuki TAMARI ◽  
Takahiro TANAKA ◽  
Isao KONDOH
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Alumina Composites

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

Preparation of WC-TiC-Ni3Al-CaF2 functionally graded self-lubricating tool material by microwave sintering and its cutting performance

2020 ◽  
Vol 39 (1) ◽  
pp. 45-53 ◽  
Author(s):  
Siwen Tang ◽  
Rui Wang ◽  
Pengfei Liu ◽  
Qiulin Niu ◽  
Guoqing Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Microwave Heating ◽  
Cutting Performance ◽  
Conventional Heating ◽  
Hard Alloys ◽  
Dry Cutting ◽  
Temperature Oxidation ◽  
Lubricating Material ◽  
Heating Technology

AbstractWith the concern of the environment, green dry cutting technology is getting more and more attention and self-lubricating tool technology plays an important role in dry cutting. Due to the demand for high temperature performance of tools during dry cutting process, cemented carbide with Ni3Al as the binder phase has received extensive attention due to its excellent high temperature strength and high temperature oxidation resistance. In this paper, WC-TiC-Ni3Al-CaF2 graded self-lubricating material and tools were prepared by microwave heating method, and its microstructure, mechanical properties and cutting performance were studied. Results show that gradient self-lubricating material can be quickly prepared by microwave heating technology, and the strength is equivalent to that of conventional heating technology. CaF2 not only plays a role in self-lubrication, but also refines the grain of the material. A reasonable gradient design can improve the mechanical properties of the material. When the gradient distribution exponent is n1 = 2, the material has high mechanical properties. Cutting experiments show that the WC-TiC-Ni3Al-CaF2 functional gradient self-lubricating tool has better cutting performance than the homogeneous WC-TiC-Ni3Al hard alloys.

Mechanical Properties of Zirconia Toughened Alumina Composites with TZP Partially Nanostructured Sintered by Liquid Fase

2008 ◽  
Vol 591-593 ◽  
pp. 436-440
Author(s):  
João Marcos K. Assis ◽  
Francisco Piorino Neto ◽  
Francisco Cristóvão Lourenço de Melo ◽  
Maria do Carmo de Andrade Nono
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Weibull Modulus ◽  
Bending Test ◽  
Sintering Aid ◽  
Zirconia Composites ◽  
Alumina Composites ◽  
Grain Size And Shape ◽  
Zirconia Toughened Alumina ◽  
Zirconia Powders

A comparative study between alumina added niobia ceramics and two alumina zirconia composites from nanostructured TZP (7% and 14% weight) was made. On this composites the zirconia were yttria stabilized and the alumina were submicron structured. As sintering aid a mixture of magnesia, niobia and talc were used on all samples. The sintering was performed at 1450 oC during 60 minutes. The characteristic grain size and shape of an alumina and zirconia powders, aggregates and agglomerates were characterized. The sintering ceramics were evaluated through hardness, fracture toughness and 4 point bending test. Weibull statistic was applied on the flexural results. Although the fracture toughness result from ZTA were lower, and seems to be affected by the liquid fase, the hardness and Weibull modulus were higher than alumina niobia. The grains size and the homogeneity of its distributions on the microstructure of this ceramics was correlated to these higher values. The results from these alumina zirconia composites showed a potential to apply as a ballistic armor material.

Sign in / Sign up

Export Citation Format

Share Document