scholarly journals Bacterial laminarinase for application in ethanol production from brown algae Sargassum sp. using halotolerant yeast

2018 ◽  
Vol 5 (1) ◽  
pp. 792-797 ◽  
Author(s):  
C.M.T. Perez ◽  
I.G. Pajares ◽  
V.A. Alcantara ◽  
J.F. Simbahan
Keyword(s):  
Ethanol Production ◽  
Brown Algae ◽  
Halotolerant Yeast

scholarly journals Ethanol production from brown seaweed using non-conventional yeasts

Bioethanol ◽  
2016 ◽  
Vol 2 (1) ◽  
Author(s):  
Oluwatosin Obata ◽  
Joseph Akunna ◽  
Heike Bockhorn ◽  
Graeme Walker
Keyword(s):  
Ethanol Production ◽  
Brown Algae ◽  
Lignin Content ◽  
Brown Seaweed ◽  
Pichia Stipitis ◽  
Yeast Fermentation ◽  
Laminaria Digitata ◽  
Yeast Strains ◽  
Wide Range ◽  
Bioprocess Technology

AbstractThe use of macroalgae (seaweed) as a potential source of biofuels has attracted considerable worldwide interest. Since brown algae, especially the giant kelp, grow very rapidly and contain considerable amounts of polysaccharides, coupled with low lignin content, they represent attractive candidates for bioconversion to ethanol through yeast fermentation processes. In the current study, powdered dried seaweeds (Ascophylum nodosum and Laminaria digitata) were pre-treated with dilute sulphuric acid and hydrolysed with commercially available enzymes to liberate fermentable sugars. Higher sugar concentrations were obtained from L. digitata compared with A. nodosum with glucose and rhamnose being the predominant sugars, respectively, liberated from these seaweeds. Fermentation of the resultant seaweed sugars was performed using two non-conventional yeast strains: Scheffersomyces (Pichia) stipitis and Kluyveromyces marxianus based on their abilities to utilise a wide range of sugars. Although the yields of ethanol were quite low (at around 6 g/L), macroalgal ethanol production was slightly higher using K. marxianus compared with S. stipitis. The results obtained demonstrate the feasibility of obtaining ethanol from brown algae using relatively straightforward bioprocess technology, together with non-conventional yeasts. Conversion efficiency of these non-conventional yeasts could be maximised by operating the fermentation process based on the physiological requirements of the yeasts.

DECOLOURIZATION AND COD REMOVAL OF WASEWATER FROM ETHANOL PRODUCTION PROCESS FROM MOLASSES BY COAGULANTION USING INORGANIC ALUM

2010 ◽  
Vol 13 (3) ◽  
pp. 92-102
Author(s):  
Trung Duc Le
Keyword(s):  
Ethanol Production ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Treated Wastewater ◽  
Treatment Processes ◽  
Physico Chemical ◽  
Biological Methods ◽  
Treatment Step ◽  
Main Material

The industrial production of ethanol by fermentation using molasses as main material that generates large quantity of wastewater. This wastewater contains high levels of colour and chemical oxygen demand (COD), that may causes serious environmental pollution. Most available treatment processes in Vietnam rely on biological methods, which often fail to treat waste water up to discharge standard. As always, it was reported that quality of treated wastewater could not meet Vietnameses discharge standard. So, it is necessary to improve the treatment efficiency of whole technological process and therefore, supplemental physico-chemical treatment step before biodegradation stage should be the appropriate choice. This study was carried out to assess the effect of coagulation process on decolourization and COD removal in molasses-based ethanol production wastewater using inorganic coaglutant under laboratory conditions. The experimental results showed that the reductions of COD and colour with the utilization of Al2(SO4)3 at pH 9.5 were 83% and 70%, respectively. Mixture FeSO4 – Al2(SO4)3 at pH 8.5 reduced 82% of colour and 70% of COD. With the addition of Polyacrylamide (PAM), the reduction efficiencies of colour, COD and turbidity by FeSO4 – Al2(SO4)3 were 87%, 73.1% and 94.1% correspondingly. It was indicated that PAM significantly reduced the turbidity of wastewater, however it virtually did not increase the efficiencies of colour and COD reduction. Furthermore, the coagulation processes using PAM usually produces a mount of sludge which is hard to be deposited.

Pyrolysis of brown algae (Bifurcaria Bifurcata) in a stainless steel tubular reactor: From a review to a case study

2018 ◽  
Vol 14 (1) ◽  
pp. 31-60 ◽  
Author(s):  
M. Y. Guida ◽  
F. E. Laghchioua ◽  
A. Hannioui
Keyword(s):  
Particle Size ◽  
Stainless Steel ◽  
Flow Rate ◽  
Brown Algae ◽  
Tubular Reactor ◽  
Nitrogen Flow ◽  
Nitrogen Flow Rate ◽  
Bifurcaria Bifurcata ◽  
Bio Oil

This article deals with fast pyrolysis of brown algae, such as Bifurcaria Bifurcata at the range of temperature 300–800 °C in a stainless steel tubular reactor. After a literature review on algae and its importance in renewable sector, a case study was done on pyrolysis of brown algae especially, Bifurcaria Bifurcata. The aim was to experimentally investigate how the temperature, the particle size, the nitrogen flow rate (N2) and the heating rate affect bio-oil, bio-char and gaseous products. These parameters were varied in the ranges of 5–50 °C/min, below 0.2–1 mm and 20–200 mL. min–1, respectively. The maximum bio-oil yield of 41.3wt% was obtained at a pyrolysis temperature of 600 °C, particle size between 0.2–0.5 mm, nitrogen flow rate (N2) of 100 mL. min–1 and heating rate of 5 °C/min. Liquid product obtained under the most suitable and optimal condition was characterized by elemental analysis, 1H-NMR, FT-IR and GC-MS. The analysis of bio-oil showed that bio-oil from Bifurcaria Bifurcata could be a potential source of renewable fuel production and value added chemicals.

Feasibility of solar assisted ethanol production

1981 ◽  
Author(s):  
M. HOLDEN ◽  
A. SHEKAR ◽  
T. SMITH
Keyword(s):  
Ethanol Production
Sign in / Sign up

Export Citation Format

Share Document