scholarly journals Influence of Valeric and Isovaleric Acids Copper Carboxylates on Tribological Characteristics of Plastic Greasings

2016 ◽  
Vol 16 (2) ◽  
pp. 100-105
Author(s):  
V. V. Terentyev ◽  
O. B. Akopova ◽  
I. A. Telegin
Keyword(s):  
Tribological Characteristics ◽  
Copper Carboxylates

A machine for real-time estimation of the tribological characteristics of materials

2020 ◽  
Vol 86 (4) ◽  
pp. 61-65
Author(s):  
M. V. Abramchuk ◽  
R. V. Pechenko ◽  
K. A. Nuzhdin ◽  
V. M. Musalimov
Keyword(s):  
Real Time ◽  
Time Estimation ◽  
Tribological Characteristics ◽  
Continuous Processing ◽  
Friction Machine ◽  
Dynamic Friction Coefficient ◽  
Displacement Sensors ◽  
Frictional Interaction ◽  
Real Time Estimation ◽  
Automated Quality Control

A reciprocating friction machine Tribal-T intended for automated quality control of the rubbing surfaces of tribopairs is described. The distinctive feature of the machine consists in implementation of the forced relative motion due to the frictional interaction of the rubbing surfaces fixed on the drive and conjugate platforms. Continuous processing of the signals from displacement sensors is carried out under conditions of continuous recording of mutual displacements of loaded tribopairs using classical approaches of the theory of automatic control to identify the tribological characteristics. The machine provides consistent visual real time monitoring of the parameters. The MATLAB based computer technologies are actively used in data processing. The calculated tribological characteristics of materials, i.e., the dynamic friction coefficient, damping coefficient and measure of the surface roughness, are presented. The tests revealed that a Tribal-T reciprocating friction machine is effective for real-time study of the aforementioned tribological characteristics of materials and can be used for monitoring of the condition of tribo-nodes of machines and mechanisms.

scholarly journals Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4217
Author(s):  
Üsame Ali Usca ◽  
Mahir Uzun ◽  
Mustafa Kuntoğlu ◽  
Serhat Şap ◽  
Khaled Giasin ◽  
...  
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Practical Significance ◽  
Tribological Characteristics ◽  
M 10 ◽  
Wide Range ◽  
The Coefficient Of Friction ◽  
Four Levels

Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

Tribological characteristics of MoS2–Nb solid lubricant film in different tribo-test conditions

2008 ◽  
Vol 203 (5-7) ◽  
pp. 766-770 ◽  
Author(s):  
Ihsan Efeoglu ◽  
Özlem Baran ◽  
Fatih Yetim ◽  
Sabri Altıntaş
Keyword(s):  
Solid Lubricant ◽  
Lubricant Film ◽  
Tribological Characteristics ◽  
Test Conditions

Tribological characteristics of the dual titanium boride layers (TiB2+TiB) on titanium alloy

2021 ◽  
Vol 47 (10) ◽  
pp. 13957-13969
Author(s):  
Yan song Zhu ◽  
Yun fei Liu ◽  
Xing nong Wei ◽  
Dong Sun ◽  
Wen zhuang Lu ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Titanium Boride ◽  
Tribological Characteristics

scholarly journals Effect of Low Hydroxyapatite Loading Fraction on the Mechanical and Tribological Characteristics of Poly(Methyl Methacrylate) Nanocomposites for Dentures

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 857
Author(s):  
Ahmed Fouly ◽  
Ahmed Mohamed Mahmoud Ibrahim ◽  
El-Sayed M. Sherif ◽  
Ahmed M.R. FathEl-Bab ◽  
A.H. Badran
Keyword(s):  
Friction Coefficient ◽  
Yield Strength ◽  
Methyl Methacrylate ◽  
Weight Fraction ◽  
Tribological Characteristics ◽  
Compressive Yield Strength ◽  
Wear Loss ◽  
Mechanical Mixing ◽  
Poly Methyl Methacrylate ◽  
Mechanical And Tribological Characteristics

Denture base materials need appropriate mechanical and tribological characteristics to endure different stresses inside the mouth. This study investigates the properties of poly(methyl methacrylate) (PMMA) reinforced with different low loading fractions (0, 0.2, 0.4, 0.6, and 0.8 wt.%) of hydroxyapatite (HA) nanoparticles. HA nanoparticles with different loading fractions are homogenously dispersed in the PMMA matrix through mechanical mixing. The resulting density, Compressive Young’s modulus, compressive yield strength, ductility, fracture toughness, and hardness were evaluated experimentally; the friction coefficient and wear were estimated by rubbing the PMMA/HA nanocomposites against stainless steel and PMMA counterparts. A finite element model was built to determine the wear layer thickness and the stress distribution along the nanocomposite surfaces during the friction process. In addition, the wear mechanisms were elucidated via scanning electron microscopy. The results indicate that increasing the concentration of HA nanoparticles increases the stiffness, compressive yield strength, toughness, ductility, and hardness of the PMMA nanocomposite. Moreover, tribological tests show that increasing the nanoparticle weight fraction considerably decreases the friction coefficient and wear loss.

Sign in / Sign up

Export Citation Format

Share Document