Elastic-wave propagation and site amplification in the Salt Lake valley, Utah, from simulated normal faulting earthquakes

1988 ◽  
Vol 78 (6) ◽  
pp. 1851-1874
Author(s):  
Harley M. Benz ◽  
Robert B. Smith

Abstract The two-dimensional seismic response of the Salt Lake valley to near- and far-field earthquakes has been investigated from simulations of vertically incident plane waves and from normal-faulting earthquakes generated on the basin-bounding Wasatch fault. The response to normal faulting earthquakes was simulated using a two-dimensional finite-element method and the plane-wave response was calculated from two-dimensional finite-difference simulations. The plane-wave simulations were then compared with observed site amplifications in the Salt Lake valley, based on seismic recordings from nuclear explosions in southern Nevada, that show 10 times greater amplification within the basin than measured values on hard-rock sites. While previous studies attribute this increased site amplification to the near-surface unconsolidated/consolidated alluvial fill contact, our synthetic seismograms suggest that in the frequency band 0.3 to 1.5 Hz at least one-half the site amplification can be attributed to the impedance contrast between the basin sediments and higher velocity basement rocks. Synthetic seismograms from vertically incident plane-wave sources and buried double-couple sources predict large amplitude Rayleigh-wave propagation from the edges of the basin and, in general, uniform site amplification. In contrast, near-field simulations of basin-bounding, normal-faulting earthquakes predict large-amplitude Rayleigh waves propagating westward from the fault across the basin. Spectra of synthetic accelerograms computed from the normal-faulting earthquakes shows that spectral amplification within the basin is primarily due to source directivity with a maxima near the surface projection of the fault that decays rapidly away from the fault. Importantly, the synthetic modeling of near-field earthquake sources show that near-field directivity effects are important and should be considered in an earthquake hazard assessment of the Salt Lake valley and similar geologic settings along the Wasatch Front.

2021 ◽  
Vol 13 ◽  
Author(s):  
Arpan Deyasi ◽  
Ratul Ghosh ◽  
Papri Chakraborty ◽  
Anwesha Adhikary ◽  
Angsuman Sarkar

: Fill factor in the negative permittivity materials are tailored within physically permissible limit to characterize the Brillouin zone for two-dimensional crystal under propagation of both s and p-polarized waves. Two lowermost bandgaps are computed along with corresponding midband frequencies, where plane wave expansion method is invoked for computational purpose. Rectangular geometrical shape is considered for the simulation, and all the results are calculated inside the ‘Γ’ point and ‘X’ point of first Brillouin zone. Simulated findings depict monotonous variations of both bandgap width as well as midband frequency for higher negative permittivity materials, when magnitude of fill factor is comparatively low, for both TE (Transverse Electric)and TM (Transverse Magnetic)mode of propagations. Lower negative permittivity leads to random fluctuations which makes it unsuitable for photonic component design. Multiple forbidden regions may be observed for some specific artificial materials which can be utilized in antenna or multi-channel filter design in higher THz region. Aims: The present paper aims to compute the shape of the first Brillouin zone from the fill factor for a two-dimensional photonic crystal structure. Background: EBG (Electromagnetic Band gap) of a photonic crystal plays a major role in determining its candidature for optical applications, which is critically controlled by fill factor. Therefore, it is significant to investigate the effect of F.F on the wave propagation characteristics of 2D PhC(Two-dimensional photonic crystal). Objective: Investigation of metamaterial based photonic crystal structure for electromagnetic bandgap analysis in the desired spectrum of interest as a function of fill factor inside the first Brillouin zone Method:Maxwell’s equations are solved using plane wave propagation method to solve the problem, and simulation is carried out in MATLAB® software. Result: Both the first and second photonic bandgaps are simultaneously computed with variation of refractive index differences of the constituent materials as well as with the fill factors. Results are extremely significant about the formation of narrowband and wideband filters on certain material combinations and structural designs. Conclusion: Better tenability is observed for metamaterial structure compared to conventional positive index materials, and fill factor has a great role in shaping the Brillouin zone and corresponding bandgap width.


Author(s):  
Riyadh Mansoor

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.


Sign in / Sign up

Export Citation Format

Share Document