scholarly journals The Equivalence of Inclined Uniaxial and Biaxial Electrical Anisotropy in Inhomogeneous Two-Dimensional Media for Homogeneous TM-Type Plane Wave Propagation Problems

2003 ◽  
Vol 43 ◽  
pp. 143-162
Author(s):  
G. A. Wilson ◽  
D. V. Thiel
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Electrical Anisotropy ◽  
Two Dimensional ◽  
Plane Wave Propagation

Out-of-plane wave propagation in two-dimensional micro-lattices

2021 ◽  
Author(s):  
Soroush Sepehri ◽  
Mahmoud Mousavi Mashhadi ◽  
Mir Masoud Seyyed Fakhrabadi
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Two Dimensional ◽  
Out Of Plane ◽  
Plane Wave Propagation

scholarly journals Wave Propagation and Band-Gap Characteristics of Chiral Lattices

2007 ◽  
Author(s):  
Stefano Gonella ◽  
Alessandro Spadoni ◽  
Massimo Ruzzene ◽  
Fabrizio Scarpa
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Band Gap ◽  
Traveling Waves ◽  
Two Dimensional ◽  
Wave Velocities ◽  
Gap Characteristics ◽  
Bloch’S Theorem ◽  
Plane Wave Propagation

Plane wave propagation in a chiral lattice is investigated through the application of Bloch’s theorem. Two-dimensional dispersion relations are estimated and analyzed to illustrate peculiar properties of chiral or non-centrosymmetric configurations and investigate the directional behavior of wave propagation for varying geometric parameters. Special attention is devoted to the determination of phase and group wave velocities. Considerations based upon the analysis of velocity plots are compared with results obtained from dispersion curves to further validate the directional behavior of the proposed lattice. Finally, The relation of directionality with frequency of the traveling waves is discussed.

scholarly journals Effects of Central Tube on Shape of Modal Duct of a Helicoid in a Simple Expansion Chamber

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Daniel Omondi Onyango ◽  
Robert Kinyua ◽  
Abel Nyakundi Mayaka
Keyword(s):  
Wave Propagation ◽  
Acoustic Wave ◽  
Plane Wave ◽  
Acoustic Pressure ◽  
Three Dimensional ◽  
The Other ◽  
Expansion Chamber ◽  
Central Tube ◽  
Simple Expansion ◽  
Plane Wave Propagation

The shape of the modal duct of an acoustic wave propagating in a muffling system varies with the internal geometry. This shape can be either as a result of plane wave propagation or three-dimensional wave propagation. These shapes depict the distribution of acoustic pressure that may be used in the design or modification of mufflers to create resonance at cut-off frequencies and hence achieve noise attenuation or special effects on the output of the noise. This research compares the shapes of acoustic duct modes of two sets of four pitch configurations of a helicoid in a simple expansion chamber with and without a central tube. Models are generated using Autodesk Inventor modeling software and imported into ANSYS 18.2, where a fluid volume from the complex computer-aided-design (CAD) geometry is extracted for three-dimensional (3D) analysis. Mesh is generated to capture the details of the fluid cavity for frequency range between 0 and 2000Hz. After defining acoustic properties, acoustic boundary conditions and loads were defined at inlet and outlet ports before computation. Postprocessed acoustic results of the modal shapes and transmission loss (TL) characteristics of the two configurations were obtained and compared for geometries of the same helical pitch. It was established that whereas plane wave propagation in a simple expansion chamber (SEC) resulted in a clearly defined acoustic pressure pattern across the propagation path, the distribution in the configurations with and without the central tube depicted three-dimensional acoustic wave propagation characteristics, with patterns scattering or consolidating to regions of either very low or very high acoustic pressure differentials. A difference of about 80 decibels between the highest and lowest acoustic pressure levels was observed for the modal duct of the geometry with four turns and with a central tube. On the other hand, the shape of the TL curve shifts from a sinusoidal-shaped profile with well-defined peaks and valleys in definite multiples of π for the simple expansion chamber, while that of the other two configurations depended on the variation in wavelength that affects the location of occurrence of cut-on or cut-off frequency. The geometry with four turns and a central tube had a maximum value of TL of about 90 decibels at approximately 1900Hz.

Plane wave propagation in microstretch thermoelastic medium with microtemperatures

2014 ◽  
Vol 21 (16) ◽  
pp. 3403-3416
Author(s):  
Rajneesh Kumar ◽  
Mandeep Kaur ◽  
SC Rajvanshi
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Thermoelastic Medium ◽  
Plane Wave Propagation
Sign in / Sign up

Export Citation Format

Share Document