Preliminary results of an investigation of crustal structure in Southeastern Europe

1966 ◽  
Vol 56 (6) ◽  
pp. 1241-1268
Author(s):  
Basil C. Papazachos ◽  
Peter E. Comninakis ◽  
John C. Drakopoulos
Keyword(s):  
Travel Time ◽  
Crustal Structure ◽  
Lower Layer ◽  
Shear Waves ◽  
Middle Layer ◽  
Average Thickness ◽  
Southeastern Europe ◽  
Preliminary Results ◽  
Longitudinal And Shear Waves ◽  
Layered Crust

Abstract Travel-time curves for the most prominent phases of the longitudinal and shear waves for epicentral distances between zero and 140 km and between 200 km and 1000 km have been constructed for Southeastern Europe. Both refraction and reflection methods indicate a three-layered crust. The average thickness is approximately 16 km for the top layer, 15 for the middle layer and 11 for the lower layer. The crustal thickness varies from about 47 to 32 km from place to place. The extremely low value 0.21 for Poisson's ratio was found in the top as well as in the middle layer.

Crustal structure in the Transvaal*

1956 ◽  
Vol 46 (4) ◽  
pp. 293-316
Author(s):  
P. G. Gane ◽  
A. R. Atkins ◽  
J. P. F. Sellschop ◽  
P. Seligman
Keyword(s):  
Travel Time ◽  
Crustal Structure ◽  
Time Data ◽  
Lower Velocity ◽  
Travel Time Data ◽  
The Mean

abstract Travel-time data are given at 25 km. intervals between 50 and 500 km. for traverses west, south, east, and north of Johannesburg. These derive from numerous seismograms of Witwatersrand earth tremors taken by means of a triggering technique. The only phases considered to be consistent are those mentioned below, and few signs of a change of velocity with depth were discovered. There were no great differences in the results for the various directions, and the mean results were: P 1 = + 0.24 + Δ / 6.18 sec . S 1 = + 0.37 + Δ / 3.66 sec . P n = + 7.61 + Δ / 8.27 sec . S n = + 11.4 + Δ / 4.73 sec . which give crustal depths of 35.1 and 33.3 km. from P and S data respectively. These depths include about 1.3 km. of superficial material of lower velocity.

RESULTS OF PETROGRAPHIC ANALYSIS OF MESHOKO CERAMICS

Kavkazologiya ◽  
2021 ◽  
pp. 12-25
Author(s):  
S.M. OSTASHINSKIJ ◽  
◽  
M.A. KULKOVA ◽  
Keyword(s):  
Lower Layer ◽  
Middle Layer ◽  
Middle Part ◽  
Petrographic Analysis ◽  
Group 4 ◽  
Group 3 ◽  
Biogenic Carbonates ◽  
Group 5 ◽  
Group 2 ◽  
Carbonate Composition

The article presents the results of petrographic analysis of the ceramics of the Chalcolithic settlement of Meshoko. A total of 42 fragments were examined (see appendix), 10 of which belong to the upper part of the monument's sediments (layers 1 and 2a; Fig. 1), 20 refer to the middle part of the sediments (layer 2b; Fig. 2), 12 – to the lower part (layer 3; Fig. 3). Based on the analysis, 5 groups of ceramics were identified (Fig. 4). Group 1 consists of fragments with an admixture of limestone, group 2 – with an admixture of diorite, group 3 – with an admixture of biogenic carbonates and sand, group 4 – with an admixture of calcite, group 5 – with an admixture of diorite and chamotte. Clays of smectite composition predominate in groups 1 and 2, while clays of smectite-carbonate composition predominate in groups 3 and 4. Comparison of these groups with stratigraphy revealed that most of the ceramics of groups 3 and 4 are confined to the lower layer, and groups 1 and 2 to the middle and upper layer (Table 1). In addition, the ceramics of these layers differ in the nature of the external surface treatment. Significant changes in the technology of making ceramics during the transition from the lower layer to the middle layer allow us to assume corresponding changes in the composition of the population.

scholarly journals PENENTUAN OPERATOR KARTU SELULER TERBAIK MENGGUNAKAN METODE AHP(ANALITYCAL HIERARCHY PROCESS)

2017 ◽  
Vol 1 (1) ◽  
pp. 61
Author(s):  
Rizaldi Rizaldi
Keyword(s):  
Decision Support ◽  
Decision Support System ◽  
Support System ◽  
Lower Layer ◽  
Middle Layer ◽  
Ahp Method ◽  
The Right ◽  
Hierarchy Process

Abstract - The role of telecommunications technology is very important, especially in changing people's lives. The development of technology in the field of communication and information can now be enjoyed by various layers of society, starting from the upper layer, middle layer or lower layer even though the results are not satisfactory. The research entitled "Decision Support System Determination of the best cellular card operator using the AHP method" aims to provide convenience for consumers who want to buy cellular cards from various telecommunications operators according to their needs and save on bags. (economical). The number of cellular card operators provided by telecommunications makes it difficult for consumers to make the right choice, according to the desired criteria. Determining cellular cards with the AHP method is the right method to overcome the problem of determining the best cellular card with many criteria offered by each operator. These criteria include the purchase price of cellular cards, rates, promos and active periods. Keywords - Cellular card operator, Decision support system, Analitycal Hierarchy Process.

scholarly journals Distribusi Vertikal Logam Pb, Zn, Cr dan Keterkaitannya Terhadap Karbon Organik Sedimen di Pantai Marunda, Jakarta

2020 ◽  
Vol 9 (2) ◽  
pp. 125-132
Author(s):  
Triyanti Nurhidayah ◽  
Lilik Maslukah ◽  
Sri Yulina Wulandari ◽  
Kurnia Kurnia
Keyword(s):  
Heavy Metals ◽  
Vertical Distribution ◽  
Lower Layer ◽  
Middle Layer ◽  
Average Concentration ◽  
Anthropogenic Activity ◽  
Sediment Texture ◽  
The Relationship ◽  
The Vertical Distribution ◽  
Very High

Pantai Marunda terletak di Teluk Jakarta dan berdekatan dengan muara Sungai Tiram. Kegiatan antropogenik di sekitar Pantai Marunda sangat tinggi, sehingga dapat menyumbang limbah yang mengandung logam berat Pb, Zn dan Cr. Limbah logam berat yang terakumulasi dalam perairan, akan  mengendap dalam sedimen dan seiring berjalannya waktu akan mengalami peningkatan. Tujuan dari penelitian ini, untuk mengetahui konsentrasi Pb, Zn, dan Cr berdasarkan kedalaman vertikal, hubungannya dengan karbon organik total (KOT) dan ukuran butir sedimen di Pantai Marunda. Sampel sedimen diambil menggunakan polietylen sediment core dan dipisahkan berdasarkan kedalamannya (1-3 cm, 4-6 cm, dan 7-9 cm). Logam berat dalam sedimen dianalisis menggunakan metode destruksi asam dan diukur nilai absorbansinya menggunakan AAS, karbon organik total menggunakan metode loss of ignition (LOI) dan analisa tekstur sedimen dengan metode pengayakan dilanjutkan pemipetan. Hasil menunjukkan bahwa konsentrasi rerata logam berat Pb, Zn, Cr secara berurutan pada lapisan atas sebesar 5,14; 107,19; dan 12,79 ppm, lapisan tengah sebesar 4,41; 100,20; 12,28  ppm serta lapisan bawah sebesar 4,8; 101,30; 14,10 ppm. Logam berat Zn dan Cr berkorelasi positif kuat terhadap KOT dan persentase lumpur, sedangkan terhadap Pb berkorelasi negatif. Hasil penelitian ini menggambarkan bahwa distribusi logam berat Pb, Zn dan Cr secara vertikal menunjukkan konsentrasi tinggi pada lapisan permukaan yaitu pada kedalaman sedimen 1-3 cm dan keberadaanya ditentukan oleh konsesntrasi  KOT dan fraksi sedimen jenis lumpur. The Marunda Beach is located on the Jakarta Bay and adjacent to the mouth of the Tiram River. Anthropogenic activity around Marunda Beach is very high, so it can contribute the heavy metals such as Pb, Zn and Cr. The heavy metal will accumulate in the sediment and over time will be increase. The purpose of this study was to determine the vertical distribution of Pb, Zn, Cr, and their relationship to total organic carbon (TOC) and the grain size. Sediment samples were taken using polyethylene cores and this sample separated based on their depth (1-3 cm, 4-6 cm, and 7-9 cm). The heavy metals were analyzed using acid destruction and absorbance values were measured using AAS, TOC using the loss of ignition (LOI) and sediment texture with a sifting method, followed by pipetting. The results showed that the average concentration of Pb, Zn, Cr in the upper layer was 5.14; 107.19; 12.79 ppm, in the middle layer of 4.41; 100.20; 12.28 ppm and in the lower layer 4.8; 101.30; 14.10 ppm, respectively. Zn and Cr are strongly positively correlated to TOC and mud, and vice versa, the relationship to Pb is negative. The results of this study found that the vertical distribution of Pb, Zn and Cr was high in the surface layer (1-3 cm) and their presence was determined by TOC concentration and mud fraction.

On the synthesis of shear-coupled PL waves

1968 ◽  
Vol 58 (6) ◽  
pp. 1849-1877 ◽  
Author(s):  
Ramesh Chander ◽  
L. E. Alsop ◽  
Jack Oliver
Keyword(s):  
United States ◽  
Phase Velocity ◽  
Travel Time ◽  
Current Knowledge ◽  
Shear Waves ◽  
The United States ◽  
Synthetic Seismograms ◽  
Travel Times ◽  
Precise Knowledge ◽  
S Curve

ABSTRACT Using the shear-coupled PL wave hypothesis of Oliver as a basis, a method is developed for computing synthetic long-period seismograms between the onset of the initial S-type body phase and the beginning of surface waves. Comparison of observed and synthetic siesmograms shows that this hypothesis can explain, in considerable detail, most of the waves with periods greater than about 20 sec recorded during this interval. The synthetic seismograms are computed easily on a small digital computer; they resemble the observed seismograms much more closely than the synthetic seismograms obtained through the superposition of normal modes of the Earth that have been reported in the literature. The synthesis of shear-coupled PL waves depends on a precise knowledge of the phase-velocity curve of the PL wave and travel-time curves of shear waves. Hence, in principle, if one of these quantities is well-known the other can be determined by this method. Phase-velocity curves of the PL wave are determined for the Baltic shield, the Russian platform, the Canadian shield, the United States, and the western North-Atlantic ocean, on the assumption that J-B travel-time curves of shear waves apply to these areas. These dispersion curves show the type of variations to be expected on the basis of the current knowledge of the crustal structures in these areas. Examples are presented to show that J-B travel-times of shear waves along paths between Kenai Peninsula, Alaska and Palisades, equatorial mid-Atlantic ridge and Palisades, and Kurile Islands and Uppsala need to be revised. Shear-wave travel-time curves that are not unique for reasons explained in the study but that give synthetic seismograms in agreement with the observed seismograms were obtained. The new S curves are compared with the J-B travel-time curves for S; and they all predict S waves to arrive later than the time given by J-B tables for epicentral distances smaller than about 30°. The new S curve for the Alaska to Palisades path appears to agree with one of the branches of a multi-branched S curve proposed recently by Ibrahim and Nuttli for the ‘average United States’ insofar as travel-times are concerned, but there are some differences in the slopes of the two curves.

scholarly journals Mathematical Modeling of Vortex Interaction Using a Three-Layer Quasigeostrophic Model. Part 2: Finite-Core-Vortex Approach and Oceanographic Application

Mathematics ◽  
2020 ◽  
Vol 8 (8) ◽  
pp. 1267
Author(s):  
Mikhail A. Sokolovskiy ◽  
Xavier J. Carton ◽  
Boris N. Filyushkin
Keyword(s):  
Large Scale ◽  
Lower Layer ◽  
Middle Layer ◽  
Vortex Interaction ◽  
Vortex Dipoles ◽  
The North ◽  
Surface Cyclone ◽  
Vertical Density ◽  
Quasigeostrophic Model ◽  
The Stability

The three-layer version of the contour dynamics/surgery method is used to study the interaction mechanisms of a large-scale surface vortex with a smaller vortex/vortices of the middle layer (prototypes of intrathermocline vortices in the ocean) belonging to the middle layer of a three-layer rotating fluid. The lower layer is assumed to be dynamically passive. The piecewise constant vertical density distribution approximates the average long-term profile for the North Atlantic, where intrathermocline eddies are observed most often at depths of 300–1600 m. Numerical experiments were carried out with different initial configurations of vortices, to evaluate several effects. Firstly, the stability of the vortex compound was evaluated. Most often, it remains compact, but when unstable, it can break as vertically coupled vortex dipoles (called hetons). Secondly, we studied the interaction between a vertically tilted cyclone and lenses. Then, the lenses first undergo anticlockwise rotation determined by the surface cyclone. The lenses can induce alignment or coupling with cyclonic vorticity above them. Only very weak lenses are destroyed by the shear stress exerted by the surface cyclone. Thirdly, under the influence of lens dipoles, the surface cyclone can be torn apart. In particular, the shedding of rapidly moving vortex pairs at the surface reflects the presence of lens dipoles below. More slowly moving small eddies can also be torn away from the main surface cyclone. In this case, they do not appear to be coupled with middle layer vortices. They are the result of large shear-induced deformation. Common and differing features of the vortex interaction, modeled in the framework of the theory of point and finite-core vortices, are noted.

Sign in / Sign up

Export Citation Format

Share Document