scholarly journals Experimental Study on Mechanical Properties and Structural Characteristics of Modified Sludge in Foundation Pit

CONVERTER ◽  
2021 ◽  
pp. 11-21
Author(s):  
Shuren Wang, Et al.
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
High Efficiency ◽  
Cement Content ◽  
Structural Characteristics ◽  
Curing Time ◽  
Hydration Products ◽  
Foundation Pit ◽  
Early Strength

To explore the efficient method of sludge modification, Ultra-fine Portland cement (UPC) was introduced as a sludge modifier regarding Ordinary Portland Cement (OPC) modified sludge as a reference. The mechanical properties and microstructural changes of UPC-modified sludge with different curing time and cement content were carried out by unconfined compressive strength (UCS), X-ray diffraction (XRD), mercury intrusion porosimetry (MIP), and scanning electron microscopy (SEM) tests. Results show that the UCS of UPC-modified sludge varies with curing time and cement content in the same way as that of OPC-modified sludge. However, compared with OPC-modified sludge, UPC has a higher sludge modification efficiency, and the UPC-modified sludge has greater compressive strength, significantly early-strength, and stronger resistance to deformation. The stress-strain curves of UPC-modified sludge present significant peak stresses, and which show a brittle failure mode. The combination of the hydration products calcium silicate hydrate (C-S-H) gels and ettringite (Aft) crystals are the essential reason for the improvement of the macroscopic strength of the modified sludge. In contrast to OPC, the UPC hydrates faster and more fully. The UPC-modified sludge can generate more hydration products under the same conditions, this is why that has high efficiency and early-strength. The conclusions obtained in this study can provide a reference for the similar engineering application of ultra-fine cement in modified sludge.

Mechanical Properties and Microstructure of Slag Solidified Body

2020 ◽  
Vol 993 ◽  
pp. 1356-1360
Author(s):  
Jun Lan Yang ◽  
Ming Li ◽  
Lu Liu ◽  
Xiao Yang Guo
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Low Temperature ◽  
Curing Time ◽  
Hydration Products ◽  
Bottom Hole ◽  
Micro Cracks ◽  
Early Strength ◽  
C 50 ◽  
Solidified Body

The mechanical properties of slag solidified bodies tend to be degraded when the temperature of slag solidified bodies is high. It is easy to crack under the action of perforated fracturing to lose the effect of sealing and interlayer sealing, and affect the cementing quality. Therefore, the mechanical properties of the solidified slag at several bottom-hole cyclic temperatures (30 °C, 50 °C, 70 °C, 90 °C) were studied in the present investigation. The results showed that the early strength of the slag solidified body cured at 90 °C was stronger than the early strength of the slag solidified body at 30 °C and 50 °C but lower than 70 °C. However, when the curing time reaches 28 days, the compressive strength of the slag solidified body at 90 °C droped sharply lower than the strength of the slag solidified body at 30°C. SEM and XRD indicated that the hydration products of slag at 90 °C were primarily network-like C-S-H gels. Compared with low temperature conditions, slag solidified bodies at high temperatures (>90 °C) were prone to micro-cracks and the structure easily damaged.

High Efficiency Ecological Concrete

2014 ◽  
Vol 604 ◽  
pp. 157-160 ◽  
Author(s):  
Patricija Kara ◽  
Aleksandrs Korjakins
Keyword(s):  
Grain Size ◽  
Compressive Strength ◽  
Portland Cement ◽  
Alkaline Earth ◽  
High Efficiency ◽  
Cement Content ◽  
Soda Lime ◽  
Waste Glass ◽  
Concrete Mixture ◽  
Concrete Properties

Waste glass is cementitious in nature when it is finely ground, and especially when it is ground in a wet environment it can be finer than Portland cement. The obtained borosilicate lamp waste glass slurry with a grain size of 0.713 – 8.088 μm has shown better fineness and stability to segregation in comparison to soda-lime and soda-alkaline earth-silicate waste glasses. Elaborated high efficiency concrete with borosilicate lamp waste glass showed 120 MPa compressive strength at 28 days and it can be considered as ecological due to reduced cement content for 20% in concrete mixture without changing concrete properties in a negative way, reduced CO2 and waste glass deposits.

Laboratory Experimental Research on Mix Ratio Test of Cement Soil

2013 ◽  
Vol 438-439 ◽  
pp. 197-201
Author(s):  
Xian Hua Yao ◽  
Peng Li ◽  
Jun Feng Guan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Ratio Test ◽  
Curing Time ◽  
Curing Conditions ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Cement Soil

Based on the generalization and analysis of laboratory experimental results on mix ratio, the effects of various factors such as cement content, water-cement ratio, curing time, curing conditions and types of cement on the mechanical properties of unconfined compressive strength of cement soil are presented. Results show that the unconfined compressive strength of cement soil increases with the growing curing time, and it is greatly affected by the cement content, water-cement ratio, cement types and curing time, while the effect of curing conditions is weak with a cement content of more than 10%. Moreover, the stress-strain of the cement soil responds with the cement content and curing time, increasing curing time and cement content makes the cement soil to be harder and brittle, and leads to a larger Young's modulus.

scholarly journals Strength development of cement-treated sand using different cement types cured at different temperatures

2018 ◽  
Vol 195 ◽  
pp. 01006
Author(s):  
Lanh Si Ho ◽  
Kenichiro Nakarai ◽  
Kenta Eguchi ◽  
Takashi Sasaki ◽  
Minoru Morioka
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Cement Content ◽  
Bound Water ◽  
Pozzolanic Reaction ◽  
Strength Development ◽  
Different Temperatures ◽  
Early Strength

This study aimed to investigate the strength development of cement-treated sand using different cement types: ordinary Portland cement (OPC), high early strength Portland cement (HPC), and moderate heat Portland cement (MPC) cured at different temperatures. The cementtreated sand specimens were prepared with 8% of cement content and cured under sealed conditions at 20οC and 40οC, and mortar specimens were also prepared for reference. The results showed that the compressive strength of cement-treated sand increased in order of MPC, OPC, and HPC under high curing temperatures. It was interesting that the compressive strength of the specimens using HPC was much larger than that of the specimen using OPC and MPC under 20οC due to the larger amount of chemically bound water. Additionally, it was revealed that under high curing temperatures, the pozzolanic reaction was accelerated in the cement-treated sand; this may be caused by the high proportions of sand in the mixtures.

scholarly journals Some Mechanical Properties of Cement Treated Base (CTB) Incorporating Waste Portland Cement Concrete Under Different Corresponding Conditions

2018 ◽  
Vol 7 (4.37) ◽  
pp. 138
Author(s):  
Asst. Prof. Dr. Khawla H. H. Shubber ◽  
Eng. Sajjad Hashim Mohamed
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Granular Materials ◽  
Compression Strength ◽  
Cement Content ◽  
Strength Increase ◽  
Test Results ◽  
Portland Cement Concrete ◽  
Cement Concrete

This research represents a trial of understanding and improving mechanical properties of base or subbase granular materials, used in pavement construction, stabilized with Portland cement known as cement treated base (CTB) in terms of density, optimum water content (O.W.C), and compression Strength of three curing ages (3, 7, 28) days under different situations. Different Portland cement percent of (0, 5, 7, 10, 12, and 15) % by weight were added to selected base course granular materials (type B according to local standard specification in Iraq). Results showed that the density of mixture increase with increasing added cement percent, while O.W.C takes its maximum value around 7% cement content, and compression strength increase with increasing cement content and curing age. Then effect of replacing 50% of natural granular materials by waste Portland cement concrete (WPCC) was investigated on the results of (0, 7& 15)% cement content on density, O.W.C and compression strength in the three curing ages. Results reveled although density of mixture cooperating WPCC for 0% cement content was higher, CTB of natural granular material were denser. On the other hand compressive strength decrease in case of using WPCC for all percent cement added and curing ages. Finally, effect of soaking in water on CTB with (7 &15)% cement compressive strength of three curing ages was studied, under three period of soaking (1 week, 2 weeks, &one month). Test results exposed that, CTB Compressive strength increase with increasing soaking period but still less than that of un-soaked and for all curing ages. For each test stage mathematics relationships with acceptable correlation were presented proofing test results tendency.  

Effect of Curing Time on the Pore Structure of the Portland Cement Concrete

2010 ◽  
Vol 44-47 ◽  
pp. 2592-2596
Author(s):  
Wei Lun Wang ◽  
Peng Liu
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Pore Structure ◽  
Mercury Intrusion Porosimetry ◽  
Curing Time ◽  
Hydration Products ◽  
Portland Cement Concrete ◽  
X Ray Diffraction ◽  
Cement Concrete ◽  
X Ray

In this paper, the influence of curing time on the compressive strength and pore structure of the Portland cement concrete was investigated. The phase composition and morphology of hydration products of Portland cement were analyzed with X-ray diffraction (XRD). In addition, the porosity and pore distribution of the concrete were also researched using mercury intrusion porosimetry (MIP), surface area and porosity analyzer (BET). The results show that the influence of curing time on the compressive strength and pore structure of the concrete is obvious. With curing time increasing, the compressive strength of the concrete increased and the porosity decreased. The corresponding fractal dimension of the pore and the microstructure were changed, as well. With time increasing, more hydration products were produced.

Effect of Curing System on Mechanical Property of Slag-Based Geopolymer

2011 ◽  
Vol 250-253 ◽  
pp. 3372-3376 ◽  
Author(s):  
Qing Wang ◽  
Xin Tu ◽  
Zhao Yang Ding ◽  
Zhi Tong Sui
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Compressive Strength ◽  
Portland Cement ◽  
Curing Temperature ◽  
Early Age ◽  
Curing Time ◽  
Commercial Applications ◽  
The Ideal

Geopolymer has been gradually attracting world attention as a potentially revolutionary material that is one of the ideal substitutes of Portland cement, and fundamental studies on geopolymer are increased rapidly because of its potential commercial applications. However, little work has been done in the field of curing system of geopolymer. In this paper, influence of curing temperature, curing time and curing humidity on the mechanical properties of slag-based geopolymer was studied by using the compressive strength as benchmark parameter. Results have shown that the early age compressive strength of geopolymer increased and the long-term compressive strength decreased at first and then increased as the curing temperature increased, 80°C was the best curing temperature. With prolonging the curing time, it was found that the compressive strength of early age of geopolymer reached the maximum ( 116.3 MPa for 1d, 97.5 MPa for 3d) as the curing time was 12h, and that of 28d geopolymer was 91.3 MPa as the curing time was 10h. It was also found that the compressive strength of geopolymer reduced evidently as the humidity increased.

Preparation and Mechanical Properties of Polyethylene-Portland Cement Composites

2009 ◽  
Vol 1242 ◽  
Author(s):  
Rivas-Vázquez L.P. ◽  
Suárez-Orduña R. ◽  
Valera-Zaragoza M. ◽  
Máas-Díaz A. De la L. ◽  
Ramírez-Vargas E.
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Plastic Waste ◽  
Cement Composites ◽  
Compression Tests ◽  
Standard Samples ◽  
Cement Ratio ◽  
Reinforcing Fibers ◽  
Waste Polyethylene

ABSTRACTThe effects of waste polyethylene aggregate as admixture agent in Portland cement at different addition polyethylene/cement ratios from 0.0156 to 0.3903 were investigated. The reinforced samples were prepared according the ASTM C 150 Standard (samples of 5 × 5 × 5 cm). The reinforcing fibers were milling at a size of 1/25 in diameter, form waste and used them to evaluate the effects in mechanical properties in cement-based composites. The evaluation of polyethylene as additive was based on results of density and compression tests. The 28-day compressive strength of cement reforced with plastic waste at a replacement polyethylene/cement ratio of 0.0468 was 23.5 MPa compared to the control concrete (7.5 MPa). The density of cement replaced with polyethylene varies from 2.114 (0% polyethylene) to 1.83 g/cm3 by the influence of polyethylene.

Mechanical Property of Phosphoaluminate Cement

2010 ◽  
Vol 150-151 ◽  
pp. 1754-1757 ◽  
Author(s):  
Peng Liu ◽  
Zhi Wu Yu ◽  
Ling Kun Chen ◽  
Zhu Ding
Keyword(s):  
Mechanical Property ◽  
Compressive Strength ◽  
Phase Composition ◽  
Electrical Properties ◽  
Pore Size Distribution ◽  
Pore Size ◽  
High Strength ◽  
Curing Time ◽  
Hydration Products ◽  
Resistance Value

The influence of curing time on the mechanical property of the phosphoaluminate cement (PAC) was investigated, and the mechanism was discussed as well. The phase composition and morphology of hydration products, electrical properties, porosity and pore size distribution of PAC cured different age were analyzed with XRD, EIS and MIP. The results showed PAC has the property of early-high strength, and the compressive strength of PAC cured for 1 day was about 70% of 28 days’. The main hydration products of PAC are micro-crystal phase and gel of phosphate and phosphoaluminate which formed compacter microstructure. In addition, there are no calcium hydroxide (CH) and ettringite (AFt) produced during the process of hydration. The compressive strength of PAC increased with age, which was due to more products continuously produced. The ac resistance analysis manifested as the change of the nyquist pattern and resistance value.

Research Progress on the Hydration of Portland Cement with Calcined Clay and Limestone

2021 ◽  
Vol 1036 ◽  
pp. 240-246
Author(s):  
Jin Tang ◽  
Su Hua Ma ◽  
Wei Feng Li ◽  
Hui Yang ◽  
Xiao Dong Shen
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Research Progress ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Early Hydration ◽  
Calcined Clay ◽  
Dense Microstructure

The use of calcined clay and limestone as supplementary cementitious materials, can have a certain influence on the hydration of Portland cement. This paper reviewed the influence of limestone and calcined clay and the mixture of limestone and calcined clay on the hydration of cement. Both limestone and calcined clay accelerate the hydration reaction in the early hydration age and enhance the properties of cement. Limestone reacts with C3A to form carboaluminate, which indirectly stabilized the presence of ettringite, while calcined clay consumed portlandite to form C-(A)-S-H gel, additional hydration products promote the densification of pore structure and increase the mechanical properties. The synergistic effect of calcined clay and limestone stabilize the existence of ettringite and stimulate the further formation of carboaluminate, as well as the C-(A)-S-H gel, contributed to a dense microstructure.

Sign in / Sign up

Export Citation Format

Share Document