2012 ◽  
Vol 1421 ◽  
Author(s):  
Russell J. Bailey ◽  
Remco Geurts ◽  
Debbie J. Stokes ◽  
Frank de Jong ◽  
Asa H. Barber

ABSTRACTThe mechanical behavior of nanocomposites is critically dependent on their structural composition. In this paper we use Focused Ion Beam (FIB) microscopy to prepare surfaces from a layered polymer nanocomposite for investigation using phase contrast atomic force microscopy (AFM). Phase contrast AFM provides mechanical information on the surface examined and, by combining with the sequential cross-sectioning of FIB, can extend the phase contract AFM into three dimensions.


1982 ◽  
Vol 63 (1) ◽  
pp. 11-15 ◽  
Author(s):  
J. G. W. Burdon ◽  
K. J. Killian ◽  
E. J. M. Campbell

1. Detection latency of a range of added elastic (0·95–4·50 kPa/l) and resistive (0·73–3·29 kPa l−1 s) loads to breathing were measured in five normal subjects. Detection latency was defined as the time from the onset of the breath to detection of the load. 2. Detection latency followed a curvilinear relationship when plotted as a function of the magnitude of the added loads. A similar relationship was found with both elastic and resistive loads although detection latencies to added elastances were longer than for added resistances. 3. When the added load was expressed in terms of comparable magnitude (peak inspiratory pressure) detection latencies for added elastances were found to be consistently longer than for added resistive loads. 4. These studies show that the detection latency to added inspiratory loads follows a reciprocal relationship, that detection latencies for elastic and resistive loads are clearly different and suggest that these loads are detected during the respiratory cycle at a time when the mechanical information regarding muscular pressure is greatest.


2020 ◽  
Author(s):  
Rafael Tapia-Rojo ◽  
Alvaro Alonso-Caballero ◽  
Julio M. Fernandez

Cells continually sample their mechanical environment using exquisite force sensors such as talin, whose folding status triggers mechanotransduction pathways by recruiting binding partners. Mechanical signals in biology change quickly over time and are often embedded in noise; however, the mechanics of force-sensing proteins have only been tested using simple force protocols, such as constant or ramped forces. Here, using our magnetic tape head tweezers design, we measure the folding dynamics of single talin proteins in response to external mechanical noise and cyclic force perturbations. Our experiments demonstrate that talin filters out external mechanical noise but detects periodic force signals over a finely-tuned frequency range. Hence, talin operates as a mechanical bandpass filter, able to read and interpret frequency-dependent mechanical information through its folding dynamics. We describe our observations in the context of stochastic resonance, which we propose as a mechanism by which mechanosensing proteins could respond accurately to force signals in the naturally noisy biological environment.


Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 473 ◽  
Author(s):  
Alessandro Genoni ◽  
Piero Macchi

In this review article, we report on the recent progresses in the field of quantum crystallography that has witnessed a massive increase of production coupled with a broadening of the scope in the last decade. It is shown that the early thoughts about extracting quantum mechanical information from crystallographic experiments are becoming reality, although a century after prediction. While in the past the focus was mainly on electron density and related quantities, the attention is now shifting toward determination of wavefunction from experiments, which enables an exhaustive determination of the quantum mechanical functions and properties of a system. Nonetheless, methods based on electron density modelling have evolved and are nowadays able to reconstruct tiny polarizations of core electrons, coupling charge and spin models, or determining the quantum behaviour at extreme conditions. Far from being routine, these experimental and computational results should be regarded with special attention by scientists for the wealth of information on a system that they actually contain.


2019 ◽  
Vol 116 (34) ◽  
pp. 16949-16954 ◽  
Author(s):  
Rong Ma ◽  
Anna V. Kellner ◽  
Victor Pui-Yan Ma ◽  
Hanquan Su ◽  
Brendan R. Deal ◽  
...  

The advent of molecular tension probes for real-time mapping of piconewton forces in living systems has had a major impact on mechanobiology. For example, DNA-based tension probes have revealed roles for mechanics in platelet, B cell, T cell, and fibroblast function. Nonetheless, imaging short-lived forces transmitted by low-abundance receptors remains a challenge. This is a particular problem for mechanoimmunology where ligand–receptor bindings are short lived, and a few antigens are sufficient for cell triggering. Herein, we present a mechanoselection strategy that uses locking oligonucleotides to preferentially and irreversibly bind DNA probes that are mechanically strained over probes at rest. Thus, infrequent and short-lived mechanical events are tagged. This strategy allows for integration and storage of mechanical information into a map of molecular tension history. Upon addition of unlocking oligonucleotides that drive toehold-mediated strand displacement, the probes reset to the real-time state, thereby erasing stored mechanical information. As a proof of concept, we applied this strategy to study OT-1 T cells, revealing that the T cell receptor (TCR) mechanically samples antigens carrying single amino acid mutations. Such events are not detectable using conventional tension probes. Each mutant peptide ligand displayed a different level of mechanical sampling and spatial scanning by the TCR that strongly correlated with its functional potency. Finally, we show evidence that T cells transmit pN forces through the programmed cell death receptor-1 (PD1), a major target in cancer immunotherapy. We anticipate that mechanical information storage will be broadly useful in studying the mechanobiology of the immune system.


SIMULATION ◽  
2020 ◽  
Vol 96 (9) ◽  
pp. 713-723
Author(s):  
Rui Zhang ◽  
Dianlei Han ◽  
Guolong Yu ◽  
Haitao Wang ◽  
Haibao Liu ◽  
...  

Inspired by the superior fixed and traction characteristics of ostrich foot toenails, we devised, optimized and manufactured the single structure and group arrangement of a new-style bionic spike for sprint shoes to improve athletic performance. The tractive performance of the bionic spike was tested by finite element analysis and experimental verification. The optimized single structure of the bionic spike had a top slope angle of 13° and the radius of the medial groove of 7.3 mm. Compared with the conventional conic spike, the maximal and stable extrusion resistances of the single bionic spike decreased by about 25% and 40% respectively, while the maximal and stable horizontal thrusts increased by about 16% and 10%, respectively. In addition, the arrangement of the bionic spikes was also optimized. Compared with the conventional spike group, the maximal and stable extrusion resistances of the bionic spike group decreased by 11.0% and 6.2%, respectively, while the maximal and stable horizontal thrusts increased by 20.0% and 16.0%, respectively. The current results may provide useful mechanical information that can help develop a better design of athletic shoes with the potential for advanced performance.


Sign in / Sign up

Export Citation Format

Share Document