Developing Measures of Effectiveness for Truck Weight Enforcement Activities

10.17226/6354 ◽  
1998 ◽  
Author(s):  
1998 ◽  
Vol 1643 (1) ◽  
pp. 152-160 ◽  
Author(s):  
F. R. Hanscom ◽  
M. W. Goelzer

A software tool was developed to determine what is accomplished as the result of truck weight enforcement efforts. Traditionally applied measures (e.g., numbers of trucks weighed and citations issued) have simply provided indications of enforcement effort. These previously applied measures failed to provide results in terms of real enforcement objectives, such as deterring overweight trucks and minimizing pavement wear and tear. Consequently the need exists to develop and validate truck weight enforcement measures of effectiveness (MOE). MOEs were developed via a series of analytical procedures. They were subsequently validated in a comprehensive four-state field evaluation. Matched (weigh-in-motion) (WIM) data sets, collected under controlled baseline and enforcement conditions, were analyzed to determine the sensitivity of candidate MOEs to actual enforcement activity. Data collection conditions were controlled in order to avoid contamination from hour-of-day, day-of-week, and seasonal effects. The following MOEs, were validated on the basis of their demonstrated sensitivity to truck weight enforcement objectives and the presence of enforcement activity: (1) severity of overweight violations, (2) proportion of overweight trucks, (3) average equivalent single-axle load (ESAL), (4) excess ESALs, and (5) bridge formula violations. These measures are sensitive to legal load-limit compliance objectives of truck weight enforcement procedures as well as the potential for overweight trucks to produce pavement deterioration. The software User Guide that statistically compares calculated MOEs between observed enforcement conditions is described in this paper. The User Guide also allows users to conduct an automated pavement design life analysis estimating, the theoretical pavement-life effect resulting from the observed enforcement activity.


2021 ◽  
Vol 11 (2) ◽  
pp. 745
Author(s):  
Sylwia Stawska ◽  
Jacek Chmielewski ◽  
Magdalena Bacharz ◽  
Kamil Bacharz ◽  
Andrzej Nowak

Roads and bridges are designed to meet the transportation demands for traffic volume and loading. Knowledge of the actual traffic is needed for a rational management of highway infrastructure. There are various procedures and equipment for measuring truck weight, including static and in weigh-in-motion techniques. This paper aims to compare four systems: portable scale, stationary truck weigh station, pavement weigh-in-motion system (WIM), and bridge weigh-in-motion system (B-WIM). The first two are reliable, but they have limitations as they can measure only a small fraction of the highway traffic. Weigh-in-motion (WIM) measurements allow for a continuous recording of vehicles. The presented study database was obtained at a location that allowed for recording the same traffic using all four measurement systems. For individual vehicles captured on a portable scale, the results were directly compared with the three other systems’ measurements. The conclusion is that all four systems produce the results that are within the required and expected accuracy. The recommendation for an application depends on other constraints such as continuous measurement, installation and operation costs, and traffic obstruction.


1998 ◽  
Vol 25 (4) ◽  
pp. 631-639 ◽  
Author(s):  
G Thater ◽  
P Chang ◽  
D R Schelling ◽  
C C Fu

A methodology is developed to more accurately estimate the static response of bridges due to moving vehicles. The method can also be used to predict dynamic responses induced by moving vehicles using weigh-in-motion (WIM) techniques. Historically, WIM is a well-developed technology used in highway research, since it has the advantage of allowing for the stealthy automatic collection of weight data for heavy trucks. However, the lack of accuracy in determining the dynamic effect in bridges has limited the potential for its use in estimating the fatigue life of bridge structures and their components. The method developed herein amends the current WIM procedures by filtering the dynamic responses accurately using the Fast Fourier Transform (FFT). Example applications of the proposed method are shown by using computer-generated data. The method is fast and improves the predicted truck weight up to 5% of the actual weight, as compared to errors up to 10% using the current WIM methods.Key words: weigh-in-motion, digital filters, FFT, bridge dynamics, in-service testing.


Oral Oncology ◽  
2006 ◽  
Vol 42 (6) ◽  
pp. 551-560 ◽  
Author(s):  
Martin C. Downer ◽  
David R. Moles ◽  
Stephen Palmer ◽  
Paul M. Speight

Sign in / Sign up

Export Citation Format

Share Document