Bonding agents to mitigate interfacial strength loss during multi-layer concrete casting

2021 ◽  
pp. 1-11
Author(s):  
Joseph J. Assaad ◽  
Yehia Daou
Keyword(s):  
Interfacial Strength ◽  
Strength Loss ◽  
Bonding Agents ◽  
Concrete Casting

Structure characterization of ground calcium carbonate flocs by fractal analysis and their effects on handsheet properties

TAPPI Journal ◽  
2013 ◽  
Vol 12 (3) ◽  
pp. 17-23 ◽  
Author(s):  
WANHEE IM ◽  
HAK LAE LEE ◽  
HYE JUNG YOUN ◽  
DONGIL SEO
Keyword(s):  
Fractal Analysis ◽  
Structural Characteristics ◽  
Fractal Dimensions ◽  
Strength Loss ◽  
Structure Characterization ◽  
Uniform Size ◽  
Cross Sectional ◽  
Floc Size ◽  
Mass Fractal ◽  
Handsheet Properties

Preflocculation of filler particles before their addition to pulp stock provides the most viable and practical solution to increase filler content while minimizing strength loss. The characteristics of filler flocs, such as floc size and structure, have a strong influence on preflocculation efficiency. The influence of flocculant systems on the structural characteristics of filler flocs was examined using a mass fractal analysis method. Mass fractal dimensions of filler flocs under high shear conditions were obtained using light diffraction spectroscopy for three different flocculants. A single polymer (C-PAM), a dual cationic polymer (p-DADMAC/C-PAM) and a C-PAM/micropolymer system were used as flocculants, and their effects on handsheet properties were investigated. The C-PAM/micropolymer system gave the greatest improvement in tensile index. The mass fractal analysis showed that this can be attributed to the formation of highly dense and spherical flocs by this flocculant. A cross-sectional analysis of the handsheets showed that filler flocs with more uniform size were formed when a C-PAM/micropolymer was used. The results suggest that a better understanding of the characteristics of preflocculated fillers and their influence on the properties of paper can be gained based on a fractal analysis.

Upscaling of foam forming technology for pilot scale

TAPPI Journal ◽  
2019 ◽  
Vol 18 (8) ◽  
Author(s):  
JANI LEHMONEN ◽  
TIMO RANTANEN ◽  
KARITA KINNUNEN-RAUDASKOSKI
Keyword(s):  
Production Efficiency ◽  
Strength Loss ◽  
Pilot Scale ◽  
Foam Density ◽  
Forming Process ◽  
Production Scale ◽  
Forming Technology ◽  
Wet Pressing ◽  
Foam Forming ◽  
Board Industry

The need for production cost savings and changes in the global paper and board industry during recent years have been constants. Changes in the global paper and board industry during past years have increased the need for more cost-efficient processes and production technologies. It is known that in paper and board production, foam typically leads to problems in the process rather than improvements in production efficiency. Foam forming technology, where foam is used as a carrier phase and a flowing medium, exploits the properties of dispersive foam. In this study, the possibility of applying foam forming technology to paper applications was investigated using a pilot scale paper forming environment modified for foam forming from conventional water forming. According to the results, the shape of jet-to-wire ratios was the same in both forming methods, but in the case of foam forming, the achieved scale of jet-to-wire ratio and MD/CD-ratio were wider and not behaving sensitively to shear changes in the forming section as a water forming process would. This kind of behavior would be beneficial when upscaling foam technology to the production scale. The dryness results after the forming section indicated the improvement in dewatering, especially when foam density was at the lowest level (i.e., air content was at the highest level). In addition, the dryness results after the pressing section indicated a faster increase in the dryness level as a function of foam density, with all density levels compared to the corresponding water formed sheets. According to the study, the bonding level of water- and foam-laid structures were at the same level when the highest wet pressing value was applied. The results of the study show that the strength loss often associated with foam forming can be compensated for successfully through wet pressing.

Does kraft hardwood and softwood pulp viscosity correlate to paper properties?

TAPPI Journal ◽  
2016 ◽  
Vol 15 (10) ◽  
pp. 643-651 ◽  
Author(s):  
ROBERT J. OGLESBY ◽  
HUMPHREY J. MOYNIHAN ◽  
RICARDO B. SANTOS ◽  
ASHOK GHOSH ◽  
PETER W. HART
Keyword(s):  
Physical Properties ◽  
Strength Loss ◽  
Strength Properties ◽  
Clear Correlation ◽  
Paper Properties ◽  
Physical Strength ◽  
Pulp Viscosity ◽  
Softwood Pulp ◽  
The Impact ◽  
Related Paper

The impact of commercially prepared, fully bleached pulp viscosity variation on handsheet physical properties was evaluated at different levels of pulp refining. Hardwood pulps from the same brownstock species mix, cooking parameters, and kappa numbers were processed through two different commercial bleach plants: one with a D0(EP)D1D2 sequence and the second with an OD0(EOP)D1 sequence. Additionally, a commercial softwood (predominately Scotts pine) brownstock pulp bleached by an OD0(EP)D1D2 sequence was employed in this study. Pulps with viscosities ranging from 14 to 21 mPa∙s were refined in a Valley beater to two freeness levels, and the associated handsheet physical properties were measured in this study. Over the pulp viscosity range of 14 to 21 mPa∙s, no clear correlation was found to exist between pulp viscosity and related paper physical properties. Finally, a series of laboratory prepared bleached pulps were purposely prepared under non-ideal conditions to reduce their final viscosities to lower values. Handsheets made from these pulps were tested in their unbeaten condition for physical strength properties. Significant and rapid strength loss occurred when the measured pulp viscosity dropped below 12 mPa∙s; overall strength properties showed no correlation to viscosity above the critical 12 mPa∙s value.

Study of Transcrystallization in Polymer Composites

1989 ◽  
Vol 170 ◽  
Author(s):  
Benjamin S. Hsiao ◽  
J. H. Eric
Keyword(s):  
Thermal Conductivity ◽  
Free Energy ◽  
Carbon Fiber ◽  
Plasma Treatment ◽  
Polymer Composites ◽  
High Performance ◽  
Interfacial Strength ◽  
Fiber Surface ◽  
Semicrystalline Polymers ◽  
First Case

AbstractTranscrystallization of semicrystalline polymers, such as PEEK, PEKK and PPS, in high performance composites has been investigated. It is found that PPDT aramid fiber and pitch-based carbon fiber induce a transcrystalline interphase in all three polymers, whereas in PAN-based carbon fiber and glass fiber systems, transcrystallization occurs only under specific circumstances. Epitaxy is used to explain the surface-induced transcrystalline interphase in the first case. In the latter case, transcrystallization is probably not due to epitaxy, but may be attributed to the thermal conductivity mismatch. Plasma treatment on the fiber surface showed a negligible effect on inducing transcrystallization, implying that surface-free energy was not important. A microdebonding test was adopted to evaluate the interfacial strength between the fiber and matrix. Our preliminary results did not reveal any effect on the fiber/matrix interfacial strength of transcrystallinity.

scholarly journals First Principle Study of TiB2 (0001)/γ-Fe (111) Interfacial Strength and Heterogeneous Nucleation

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1573
Author(s):  
Qin Wang ◽  
Peikang Bai ◽  
Zhanyong Zhao
Keyword(s):  
Stainless Steel ◽  
Heterogeneous Nucleation ◽  
316L Stainless Steel ◽  
Interfacial Strength ◽  
Interface Energy ◽  
Interface Fracture ◽  
Partial Density ◽  
Covalent Bonds ◽  
Tib2 Particles ◽  
Adhesion Work

TiB2/316L stainless steel composites were prepared by selective laser melting (SLM), and the adhesion work, interface energy and electronic structure of TiB2/γ-Fe interface in TiB2/316L stainless steel composites were investigated to explore the heterogeneous nucleation potential of γ-Fe grains on TiB2 particles using first principles. Six interface models composed of three different stacking positions and two different terminations were established. The B-terminated-top 2 site interface (“B-top 2”) was the most stable because of the largest adhesion work, smallest interfacial distances, and smallest interfacial energy. The difference charge density and partial density of states indicated that a large number of strong Fe-B covalent bonds were formed near the “B-top 2” interface, which increased the stability of interface. Fracture analysis revealed that the bonding strength of the “B-top 2” interface was higher than that of the Fe matrix, and it was difficult to fracture at the interface. The interface energy at the Ti-poor position in the “B-top 2” interface model was smaller than that of the γ-Fe/Fe melt, indicating that TiB2 had strong heterogeneous nucleation potency for γ-Fe.

scholarly journals Wettability in Metal Matrix Composites

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1034
Author(s):  
Massoud Malaki ◽  
Alireza Fadaei Tehrani ◽  
Behzad Niroumand ◽  
Manoj Gupta
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Aluminum Matrix ◽  
Interfacial Strength ◽  
High Strength ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Metal Matrix Nanocomposites ◽  
Aerospace Applications ◽  
Matrix Nanocomposites

Metal matrix composites (MMCs) have been developed in response to the enormous demand for special industrial materials and structures for automotive and aerospace applications, wherein both high-strength and light weight are simultaneously required. The most common, inexpensive route to fabricate MMCs or metal matrix nanocomposites (MMNCs) is based on casting, wherein reinforcements like nanoceramics, -carbides, -nitrides, elements or carbon allotropes are added to molten metal matrices; however, most of the mentioned reinforcements, especially those with nanosized reinforcing particles, have usually poor wettability with serious drawbacks like particle agglomerations and therefore diminished mechanical strength is almost always expected. Many research efforts have been made to enhance the affinity between the mating surfaces. The aim in this paper is to critically review and comprehensively discuss those approaches/routes commonly employed to boost wetting conditions at reinforcement-matrix interfaces. Particular attention is paid to aluminum matrix composites owing to the interest in lightweight materials and the need to enhance the mechanical properties like strength, wear, or creep resistance. It is believed that effective treatment(s) may enormously affect the wetting and interfacial strength.

Evaluation of interfacial strength between hydrating cement paste and epoxy coating

2021 ◽  
Vol 279 ◽  
pp. 122511
Author(s):  
Pratik Gujar ◽  
Aleena Alex ◽  
Manu Santhanam ◽  
Pijush Ghosh
Keyword(s):  
Cement Paste ◽  
Interfacial Strength ◽  
Epoxy Coating
Sign in / Sign up

Export Citation Format

Share Document