Monitoring of Fluctuations in the Physical Properties of a Class C Fly Ash

1986 ◽  
Vol 86 ◽  
Author(s):  
Scott Schlorholtz ◽  
Ken Bergeson ◽  
Turgut Demirel
Keyword(s):  
Fly Ash ◽  
Physical Properties ◽  
Setting Time ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Soil Base ◽  
Volume Stability ◽  
Testing Procedures ◽  
Physical Tests

ABSTRACTThe “quality” of fly ash produced during 1985 at Ottumwa Generation Station, was evaluated by two different experimental programs. The first consisted of the physical tests specified in ASTM C 311; these results are applicable to the use of fly ash as an admixture to portland cement concrete. The second consisted of monitoring the changes in the physical properties of fly ash pastes; these results would be applicable to the use of fly ash as a grout or a soil base stabilization agent. The physical properties monitored during the testing program were compressive strength, volume stability and setting time. In general, the results obtained from the two testing programs were quite different. When using testing procedures defined by ASTM C 311 the fly ash appeared quite uniform, but results obtained from the fly ash pastes were quite erratic. It was found that compressive strengths of the pastes can vary by a factor of five in rather short periods of time.

Low Cement/High Fly Ash Concretes: Their Properties and Response to Chemical Admixtures

1987 ◽  
Vol 113 ◽  
Author(s):  
V. H. Dodson
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Calcium Hydroxide ◽  
Pozzolanic Reaction ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Fly Ashes ◽  
Chemical Admixtures ◽  
Reaction With Water

ABSTRACTIn practice, the amount of fly ash added to portland cement concrete varies depending upon the desired end properties of the concrete. Generally, when a given portland cement concrete is redesigned to include fly ash, between 10 and 50% of the cement is replaced by a volume of fly ash equal to that of the cement. Sometimes as much as twice the volume of the cement replaced, although 45.4 kg (100 lbs) of cement will only produce enough calcium hydroxide during its reaction with water to react with about 9 kg (20 lbs) of a typical fly ash. The combination of large amounts of certain fly ashes with small amounts of portland cement in concrete has been found to produce surprisingly high compressive strengths, which cannot be accounted for by the conventional “pozzolanic reaction”. Ratios of cement to fly ash as high as 1:15 by weight can produce compressive strengths of 20.7 MPa (3,000 psi) at I day and over 41.4 MPa (6,000 psi) at 28 days. Methods of identifying these “hyperactive” fly ashes along with some of the startling results, with and without chemical admixtures are described.

The Effect of Substituting Rdf on the Physical and Environmental Properties of Coal Fly Ash

1988 ◽  
Vol 136 ◽  
Author(s):  
Ashaari B. Mohamad ◽  
David L. Gress
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Activity Index ◽  
Coal Fly Ash ◽  
Pozzolanic Activity ◽  
Portland Cement Concrete ◽  
Fly Ash Concrete ◽  
Refuse Derived Fuel ◽  
Cadmium And Lead

ABSTRACTRefuse-derived-fuel (RDF) consisting mainly of waste paper and plastics is a viable fuel source for the production of power. An experimental test burn partially substituting coal with RDF was undertaken by the Public Service of New Hampshire at the Merrimack Power Station.Five percent and ten percent RDF were substituted, on a BTU basis, for coal in the test bums. The chemical and physical properties of the resulting fly ash were determined. Twelve test burn days were run with 4 days of 5% RDF and 8 days of 10% RDF. Emphasis was placed on investigating the effect of the RDF fly ash on Portland cement concrete.Most of the chemical and physical properties of the coal-RDF fly ash were found to be comparable with ordinary coal fly ash except for the amount of cadmium and lead, the pozzolanic activity index and the compressive strength of fly ash concrete. Cadmium and lead were at average levels of 5.1 ppm and 102.6 ppm for the 5% RDF, and 7.8 ppm and 198.3 ppm for the 10% RDF, respectively. Although the pozzolanic activity index of coal-RDF fly ash increases over normal coal fly ash, preliminary results show that the 28-day compressive strength of concrete with direct replacement of cement and sand decreases by up to 30%. Leaching tests on crushed concrete were conducted to evaluate the environmental effect of acid rain.

Influence of Storage Conditions on Quality of Fly Ashes

2014 ◽  
Vol 1000 ◽  
pp. 59-62
Author(s):  
Hana Kalousová ◽  
Eva Bartoníčková ◽  
Tomáš Opravil
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Storage Conditions ◽  
Fly Ashes ◽  
Volume Stability ◽  
Stock Pile ◽  
Long Time ◽  
Made In

The presented paper deals with the issue of influence of storage conditions on the quality of conventional fly ashes which are produced by combustion of lignite. These ashes were stockpiled for long time. A borehole for sampling was made in the fly ash stock-pile. Total depth of the borehole was 20 m. Samples of fly ashes taken from every single meter were analyzed and next mechanical properties and the volume stability of materials containing these fly ashes were tested. The quality of fly ashes especially with respect to the possibility to use them as components of pastes, mortars and concretes as pozzolanic admixture or fine filler was evaluated.

Compressive stress-strain model for low-calcium fly ash-based geopolymer and heat-cured Portland cement concrete

2016 ◽  
Vol 73 ◽  
pp. 136-146 ◽  
Author(s):  
Amin Noushini ◽  
Farhad Aslani ◽  
Arnaud Castel ◽  
Raymond Ian Gilbert ◽  
Brian Uy ◽  
...  
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Compressive Stress ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Stress Strain ◽  
Low Calcium ◽  
Strain Model

EXPLORATORY STUDY ON THE MECHANICAL AND PHYSICAL PROPERTIES OF CONCRETE CONTAINING SULFUR

2015 ◽  
Vol 77 (32) ◽  
Author(s):  
David Yeoh ◽  
Koh Heng Boon ◽  
Norwati Jamaluddin
Keyword(s):  
Portland Cement ◽  
Physical Properties ◽  
Ordinary Portland Cement ◽  
Cement Content ◽  
Drying Shrinkage ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Complete Replacement ◽  
Mechanical And Physical Properties ◽  
Ordinary Portland Cement Concrete

This research is an exploratory experiment into sulfur concrete used not as a complete replacement of cement but as an additional material in percentage of the cement content. The aim of this research was to explore the possible appreciation of mechanical and physical properties of concrete containing sulfur with percentages of 1%, 5% and 10% of the cement content. The sulfur used here was not heat-activated, hence the binding effect in sulfur was absent. The experimental results revealed that concrete containing sulfur did not perform better in their strength properties, both compressive strength and flexural strength. The physical properties such as water penetration and water absorption for concrete containing sulfur also showed poor performance in comparison to ordinary Portland cement concrete. Such phenomena are very likely due to the sulfur not being activated by heat. Carbonation test did not show good results as a longer term of testing is required. Drying shrinkage property was found to be encouraging in that concrete containing 10% sulfur had quite significant reduction in drying shrinkage as opposed to ordinary Portland cement concrete. 

Physical Properties of Volcanic Ash Based Geopolymer Concrete

2016 ◽  
Vol 841 ◽  
pp. 1-6 ◽  
Author(s):  
Puput Risdanareni ◽  
Adjib Karjanto ◽  
Febriano Khakim
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Volcanic Ash ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Ash Content ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Time Test

This paper describes the result of investigating volcanic ash of Mount Kelud as fly ash substitute material to produce geopolymer concrete. The test was held on geopolymer concrete blended with 0%, 25%, 50% and 100% fly ash replacement with volcanic ash. Natrium Hidroxide (NaOH) with concentration of 12 molar and Natrium Silicate (Na2SiO3) were used as alkaline activator. While alkali-activator ratio of 2 was used in this research. The physical properties was tested by porosity and setting time test, while split tensile strength presented to measure brittle caracteristic of geopolymer concrete. The result shown that increasing volcanic ash content in the mixture will increase setting time of geopolymer paste. On the other hand increasing volcanic ash content will reduce split tensile strength and porosity of geopolymer concrete. After all replacing fly ash with volcanic ash was suitable from 25% to 50% due to its optimum physical and mechanical properties.

KOHONEN'S FEATURE MAPS FOR FLY ASH CATEGORIZATION

2006 ◽  
Vol 16 (06) ◽  
pp. 457-466 ◽  
Author(s):  
M. C. NATARAJA ◽  
M. A. JAYARAM ◽  
C. N. RAVIKUMAR
Keyword(s):  
Fly Ash ◽  
Classification Scheme ◽  
Environmental Benefits ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Feature Maps ◽  
Fly Ashes ◽  
One Dimensional ◽  
Chemical Attributes

Fly ash is a common admixture used in concrete and may constitute up to 50% by weight of the total binder material. Incorporation of fly ash in Portland-cement concrete is highly desirable due to technological, economic, and environmental benefits. This article demonstrates the use of artificial intelligence neural networks for the classification of fly ashes in to different groups. Kohonen's Self Organizing Feature Maps is used for the purpose. As chemical composition of fly ash is crucial in the performance of concrete, eight chemical attributes of fly ashes have been considered. The application of simple Kohonen's one-dimensional feature maps permitted to differentiate three main groups of fly ashes. Three one-dimensional feature maps of topology 8–16, 8–24 and 8–32 were explored. The overall classification result of 8-16 topology was found to be significant and encouraging. The data pertaining to 80 fly ash samples were collected from standard published works. The categorization was found to be excellent and compares well with Canadian Standard Association's [CSA A 3000] classification scheme.

Sign in / Sign up

Export Citation Format

Share Document