A Study of Substrate Orientation Dependence of the Solid-Phase Epitaxial Growth of Amorphised GaAs

1998 ◽  
Vol 523 ◽  
Author(s):  
K. B. Belay ◽  
D. J. Llewellyn ◽  
M. C. Ridgway
Keyword(s):  
Epitaxial Growth ◽  
Rutherford Backscattering Spectrometry ◽  
Solid Phase ◽  
Liquid Nitrogen Temperature ◽  
Amorphous Layer ◽  
Orientation Dependence ◽  
Ex Situ ◽  
Cross Sectional ◽  
Substrate Orientation

AbstractIn-situ transmission electron microscopy (TEM) has been utilized in conjunction with conventional ex-situ Rutherford backscattering spectrometry and channeling (RBS/C), in-situ time resolved reflectivity (TRR) and ex-situ TEM to study the influence of substrate orientation on the solid-phase epitaxial growth (SPEG) of amorphised GaAs. A thin amorphous layer was produced on semi-insulating (100), (110) and (111) GaAs substrates by ion implantation of 190 and 200 keV Ga and As ions, respectively, to a total dose of 1e14/cm2. During implantation, substrates were maintained at liquid nitrogen temperature. In-situ annealing at ∼260°C was performed in the electron microscope and the data obtained was quantitatively analysed. It has been demonstrated that the non-planarity of the crystalline-amorphous (c/a)-interface was greatest for the (111) substrate orientation and least for the (110) substrate orientation. The roughness was measured in terms of the length of the a/c-interface in given window as a function of depth on a frame captured from the recorded video of the in-situ TEM experiments. The roughness of the c/a-interface was determined by the size of the angle subtended by the microtwins with respect to the interface on ex-situ TEM cross-sectional micrographs. The angle was both calculated and measured and was the largest in the case of (111) plane. The twinned fraction as a function of orientation, was calculated in terms of the disorder measured from the RBS/C and it was greatest for the (111) orientation.

Low Temperature Silicon Epitaxial Growth by Plasma Enhanced Chemical Vapor Deposition From SiH4/He/H2

1991 ◽  
Vol 235 ◽  
Author(s):  
Yung-Jen Lin ◽  
Ming-Deng Shieh ◽  
Chiapying Lee ◽  
Tri-Rung Yew
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Epitaxial Growth ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Ex Situ ◽  
Epitaxial Layers ◽  
Cross Sectional ◽  
Transmission Electron

ABSTRACTSilicon epitaxial growth on silicon wafers were investigated by using plasma enhanced chemical vapor deposition from SiH4/He/H2. The epitaxial layers were growm at temperatures of 350°C or lower. The base pressure of the chamber was greater than 2 × 10−5 Torr. Prior to epitaxial growth, the wafer was in-situ cleaned by H2 baking for 30 min. The epi/substrate interface and epitaxial layers were observed by cross-sectional transmission electron microscopy (XTEM). Finally, the influence of the ex-situ and in-situ cleaning processes on the qualities of the interface and epitaxial layers was discussed in detail.

scholarly journals Effect of Non-Hydrostatic Stress on Kinetics and Interfacial Roughness During Solid Phase Epitaxial Growth in Si

1996 ◽  
Vol 441 ◽  
Author(s):  
William Barvosa-Carter ◽  
Michael J. Aziz
Keyword(s):  
Growth Rate ◽  
Epitaxial Growth ◽  
Uniaxial Compression ◽  
Solid Phase ◽  
Hydrostatic Stress ◽  
Uniaxial Stress ◽  
Cross Sectional ◽  
Time Resolved ◽  
Crystal Interface

AbstractWe report preliminary in-situ time-resolved measurements of the effect of uniaxial stress on solid phase epitaxial growth in pure Si (001) for the case of stress applied parallel to the amorphous-crystal interface. The growth rate is reduced by the application of uniaxial compression, in agreement with previous results. Additionally, the velocity continues to decrease with time. This is consistent with interfacial roughening during growth under stress, and is supported by both reflectivity measurements and cross-sectional TEM observations. We present a new kinetically-driven interfacial roughening mechanism which is consistent with our observations.

Low Temperature Silicon Epitaxial Growth by Plasma Enhanced Chemical Vapor Deposition from SiH4/He/H2

1991 ◽  
Vol 236 ◽  
Author(s):  
Yung-Jen Lin ◽  
Ming-Deng Shieh ◽  
Chiapying Lee ◽  
Tri-Rung Yew
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Epitaxial Growth ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Ex Situ ◽  
Epitaxial Layers ◽  
Cross Sectional ◽  
Transmission Electron

AbstractSilicon epitaxial growth on silicon wafers were investigated by using plasma enhanced chemical vapor deposition from SiH4/He/H2. The epitaxial layers were growm at temperatures of 350°C or lower. The base pressure of the chamber was greater than 2 × 10−5 Torr. Prior to epitaxial growth, the wafer was in-situ cleaned by H2 baking for 30 min. The epi/substrate interface and epitaxial layers were observed by cross-sectional transmission electron microscopy (XTEM). Finally, the influence of the ex-situ and in-situ cleaning processes on the qualities of the interface and epitaxial layers was discussed in detail.

In-Situ Transmission Electron Microscopy of the Solid-Phase Epitaxial Growth of GaAs: Sample Preparation and Artifact Characterization

1997 ◽  
Vol 480 ◽  
Author(s):  
K. B. Belay ◽  
M. C. Ridgway ◽  
D. J. Llewellyn
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Epitaxial Growth ◽  
Solid Phase ◽  
Ion Beam ◽  
Ex Situ ◽  
In Situ Tem ◽  
Transmission Electron

AbstractIn-situ transmission electron microscopy (TEM) has been used to characterize the solidphase epitaxial growth of amorphized GaAs at a temperature of 260°C. To maximize heat transfer from the heated holder to the sample and minimize electron-irradiation induced artifacts, non-conventional methodologies were utilized for the preparation of cross-sectional samples. GaAs (3xI) mm rectangular slabs were cut then glued face-to-face to a size of (6x3) mm stack by maintaining the TEM region at the center. This stack was subsequently polished to a thickness of ~ 200 ýtm. A 3 mm disc was then cut from it using a Gatan ultrasonic cutter. The disc was polished and dimpled on both sides to a thickness of ~15 mimT.h is was ion-beam milled at liquid nitrogen temperature to an electron-transparent layer. From a comparison of in-situ and ex-situ measurements of the recrystallization rate, the actual sample temperature during in-situ characterization was estimated to deviate by ≤ 20°C from that of the heated holder. The influence of electron-irradiated was found to be negligible by comparing the recrystallization rate and microstructure of irradiated and unirradiated regions of comparable thickness. Similarly, the influence of “thin-foil effect” was found to be negligible by comparing the recrystallization rate and microstructure of thick and thin regions, the former determined after the removal of the sample from the microscope and further ion-beam milling of tens of microns of material. In conclusion, the potential influence of artifacts during in-situ TEM can be eliminated by the appropriate choice of sample preparation procedures.

scholarly journals Substrate orientation dependence on the solid phase epitaxial growth rate of Ge

2013 ◽  
Vol 113 (3) ◽  
pp. 033505 ◽  
Author(s):  
B. L. Darby ◽  
B. R. Yates ◽  
I. Martin-Bragado ◽  
J. L. Gomez-Selles ◽  
R. G. Elliman ◽  
...  
Keyword(s):  
Growth Rate ◽  
Epitaxial Growth ◽  
Solid Phase ◽  
Orientation Dependence ◽  
Substrate Orientation

Characterization of the Solid-Phase Epitaxial Growth of Amorphized Gaas with In-Situ Electron Microscopy

1996 ◽  
Vol 421 ◽  
Author(s):  
K. B. Belay ◽  
M. C. Ridgway ◽  
D. J. Llewellyn
Keyword(s):  
Electron Microscopy ◽  
Single Crystal ◽  
Epitaxial Growth ◽  
Solid Phase ◽  
Ex Situ ◽  
In Situ Tem ◽  
Recrystallization Process ◽  
Time Resolved ◽  
Rich Material

AbstractThe influence of non-stoichiometry on the solid-phase epitaxial growth of amorphized GaAs has been studied with in-situ Transmission Electron Microscopy (TEM). Ion-implantation has been used to produce microscopic non-stoichiometry via Ga and As implants and macroscopic non-stoichiometry via Ga or As implants. It has been demonstrated that amorphous GaAs recrystallizes into a thin single-crystal layer and a thick heavily twinned layer. Video images of the recrystallization process have been quantified for the first time to study the velocity of the crystalline/amorphous (c/a)-interface as a function of depth and ion species. Regrowth rates of the single crystal and twinned layers as functions of non-stoichiometry have been calculated. The phase transformation is rapid in Ga-rich material. In-situ TEM results are consistent with conventional in-situ Time Resolved Reflectivity, ex-situ Rutherford Backscattering Spectroscopy and Channelling measurements and ex-situ TEM.

A New Method of Wafer Level Plan View TEM Sample Preparation by DualBeam

2008 ◽  
Author(s):  
Hyoung H. Kang ◽  
Michael A. Gribelyuk ◽  
Oliver D. Patterson ◽  
Steven B. Herschbein ◽  
Corey Senowitz
Keyword(s):  
Sample Preparation ◽  
Ex Situ ◽  
Wafer Level ◽  
Cross Sectional ◽  
Plan View ◽  
Manufacturing Line ◽  
Transmission Electron ◽  
Thin Lamella ◽  
Preparation Techniques

Abstract Cross-sectional style transmission electron microscopy (TEM) sample preparation techniques by DualBeam (SEM/FIB) systems are widely used in both laboratory and manufacturing lines with either in-situ or ex-situ lift out methods. By contrast, however, the plan view TEM sample has only been prepared in the laboratory environment, and only after breaking the wafer. This paper introduces a novel methodology for in-line, plan view TEM sample preparation at the 300mm wafer level that does not require breaking the wafer. It also presents the benefit of the technique on electrically short defects. The methodology of thin lamella TEM sample preparation for plan view work in two different tool configurations is also presented. The detailed procedure of thin lamella sample preparation is also described. In-line, full wafer plan view (S)TEM provides a quick turn around solution for defect analysis in the manufacturing line.

Structural Quality And Electrical Behavior Of Epitaxial High-κ Y2O3 / Si(001)

2002 ◽  
Vol 745 ◽  
Author(s):  
G. Vellianitis ◽  
G. Apostolopoulos ◽  
A. Dimoulas ◽  
K. Argyropoulos ◽  
B. Mereu ◽  
...  
Keyword(s):  
Leakage Current ◽  
Wide Band ◽  
Amorphous Layer ◽  
Ex Situ ◽  
Structural Quality ◽  
Wide Band Gap ◽  
Annealing Temperatures ◽  
Grown Sample ◽  
Transistor Fabrication

ABSTRACTY2O3 thin films were grown directly on Si (001) by MBE and annealed in-situ under UHV at various annealing temperatures. The samples were investigated in-situ by RHEED and ex-situ by HRTEM. A 7 to 15 Å thick non-uniform interfacial amorphous layer is observed in the as-grown sample. After annealing at 490°C under UHV for 30 minutes the amorphous layer is reduced and a sharp Y2O3/Si interface is obtained. At higher annealing temperatures, YSi2 islands start to form at the Y2O3/Si interface. I-V measurements performed on generic MIS structures show that the annealed samples exhibit higher leakage current density than the as-grown sample, due to reduction of the wide band gap interfacial layer. Leakage current densities in annealed samples remain below 1A/cm2, which is acceptable for future high-κ transistor fabrication.

Sign in / Sign up

Export Citation Format

Share Document