Two-View Small-Angle Wedge Sample Preparation By Hand Tools For Transmission Electron Microscopy Of Semiconductors And Related Materials

1997 ◽  
Vol 480 ◽  
Author(s):  
Suli Suder ◽  
C. A. Faunce ◽  
S. E. Donnelly
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Small Angle ◽  
Hand Tools ◽  
Cross Sectional ◽  
Plan View ◽  
Tin Films ◽  
Transmission Electron ◽  
Ion Implanted

AbstractVarious small-angle wedge two-view samples have been prepared by a small-angle cleavage technique using hand tools and examined by transmission electron microscopy. Cleaved wedges from the same material are mounted both as plan-view and cross-sectional samples on the same TEM specimen grid allowing convenient examination in both views. Samples of Si3N4, Zr, Co and TiN/CN/TiN films deposited on Si, and He ion implanted Si prepared by this technique are shown to be suitable for analysis in the TEM.

TEM Sample Preparation Tricks for Advanced DRAMs

2015 ◽  
Author(s):  
Ching Shan Sung ◽  
Hsiu Ting Lee ◽  
Jian Shing Luo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Characterization Of Materials

Abstract Transmission electron microscopy (TEM) plays an important role in the structural analysis and characterization of materials for process evaluation and failure analysis in the integrated circuit (IC) industry as device shrinkage continues. It is well known that a high quality TEM sample is one of the keys which enables to facilitate successful TEM analysis. This paper demonstrates a few examples to show the tricks on positioning, protection deposition, sample dicing, and focused ion beam milling of the TEM sample preparation for advanced DRAMs. The micro-structures of the devices and samples architectures were observed by using cross sectional transmission electron microscopy, scanning electron microscopy, and optical microscopy. Following these tricks can help readers to prepare TEM samples with higher quality and efficiency.

Structural Investigation of Photoluminescent Porous Si by Transmission Electron Microscopy

1992 ◽  
Vol 281 ◽  
Author(s):  
S. Shih ◽  
K. H. Jung ◽  
D. L. Kwong
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Structural Investigation ◽  
Amorphous Material ◽  
Porous Si ◽  
Plan View ◽  
Mesh Structure ◽  
Transmission Electron ◽  
Minimal Damage

ABSTRACTWe have developed a new, minimal damage approach for examination of luminescent porous Si layers (PSLs) by transmission electron microscopy (TEM). In this approach, chemically etched PSLs are fabricated after conventional plan-view TEM sample preparation. A diffraction pattern consisting of a diffuse center spot, characteristic of amorphous material, is primarily observed. However, crystalline, microcrystalline, and amorphous regions could all be observed in selected areas. A crystalline mesh structure could be observed in some of the thin areas near the pinhole. The microcrystallite sizes were 15–150 Å and decreased in size when located further from the pinhole.

Direct Deposition Reactions Between Nickel and Silicon Substrates

1993 ◽  
Vol 311 ◽  
Author(s):  
Lin Zhang ◽  
Douglas G. Ivey
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Silicon Substrates ◽  
Silicide Formation ◽  
Cross Sectional ◽  
Deposition Rates ◽  
Plan View ◽  
X Ray ◽  
Si Substrates ◽  
Transmission Electron

ABSTRACTSilicide formation through deposition of Ni onto hot Si substrates has been investigated. Ni was deposited onto <100> oriented Si wafers, which were heated up to 300°C, by e-beam evaporation under a vacuum of <2x10-6 Torr. The deposition rates were varied from 0.1 nm/s to 6 nm/s. The samples were then examined by both cross sectional and plan view transmission electron microscopy (TEM), energy dispersive x-ray spectroscopy and electron diffraction. The experimental results are discussed in terms of a new kinetic model.

A Method for Directly Correlating Site-Specific Cross-Sectional and Plan-View Transmission Electron Microscopy of Individual Nanostructures

2012 ◽  
Vol 18 (6) ◽  
pp. 1410-1418 ◽  
Author(s):  
Daniel K. Schreiber ◽  
Praneet Adusumilli ◽  
Eric R. Hemesath ◽  
David N. Seidman ◽  
Amanda K. Petford-Long ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Region Of Interest ◽  
Ex Situ ◽  
3D Analysis ◽  
Cross Sectional ◽  
Plan View ◽  
Site Specific ◽  
Dual Beam ◽  
Transmission Electron

AbstractA sample preparation method is described for enabling direct correlation of site-specific plan-view and cross-sectional transmission electron microscopy (TEM) analysis of individual nanostructures by employing a dual-beam focused-ion beam (FIB) microscope. This technique is demonstrated using Si nanowires dispersed on a TEM sample support (lacey carbon or Si-nitride). Individual nanowires are first imaged in the plan-view orientation to identify a region of interest; in this case, impurity atoms distributed at crystalline defects that require further investigation in the cross-sectional orientation. Subsequently, the region of interest is capped with a series of ex situ and in situ deposited layers to protect the nanowire and facilitate site-specific lift-out and cross-sectioning using a dual-beam FIB microscope. The lift-out specimen is thinned to electron transparency with site-specific positioning to within ∼200 nm of a target position along the length of the nanowire. Using the described technique, it is possible to produce correlated plan-view and cross-sectional view lattice-resolved TEM images that enable a quasi-3D analysis of crystalline defect structures in a specific nanowire. While the current study is focused on nanowires, the procedure described herein is general for any electron-transparent sample and is broadly applicable for many nanostructures, such as nanowires, nanoparticles, patterned thin films, and devices.

High-temperature in situ Cross-sectional Transmission Electron Microscopy Investigation of Crystallization Process of Yttrium-stabilized Zirconia/Si and Yttrium-stabilized Zirconia/SiOx/Si Thin Films

2005 ◽  
Vol 20 (7) ◽  
pp. 1878-1887 ◽  
Author(s):  
Takanori Kiguchi ◽  
Naoki Wakiya ◽  
Kazuo Shinozaki ◽  
Nobuyasu Mizutani
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Temperature ◽  
Crystallization Process ◽  
Stabilized Zirconia ◽  
Cross Sectional ◽  
Plan View ◽  
Transmission Electron ◽  
Tem Method

The crystallization process of yttria-stabilized zirconia (YSZ) gate dielectrics deposited on p-Si (001) and SiOx/p-Si(001) substrates and the growth process of SiOx has been investigated directly using high-temperature in situ cross-sectional view transmission electron microscopy (TEM) method and high-temperature plan-view in-situ TEM method. The YSZ layer is crystallized by the nucleation and growth mechanism at temperatures greater than 573 K. Nucleation originates from the film surface. Nucleation occurs randomly in the YSZ layer. Subsequently, the crystallized YSZ area strains the Si surface. Finally, it grows in the in-plane direction with the strain, whereas, if a SiOx layer of 1.4 nm exists, it absorbs the crystallization strain. Thereby, an ultrathin SiOx layer can relax the strain generated in the Si substrate in thin film crystallization process.

Sign in / Sign up

Export Citation Format

Share Document