Temperature and Moisture Dependence of Dielectric Constant for Bulk Silica Aerogels

1997 ◽  
Vol 476 ◽  
Author(s):  
L.W. Hrubesh ◽  
S. R. Buckley
Keyword(s):  
Dielectric Constant ◽  
Microwave Frequency ◽  
Solid Material ◽  
Silica Aerogels ◽  
Dielectric Constants ◽  
Surface Areas ◽  
Nano Structures ◽  
Low Thermal Expansion ◽  
Heat Treated ◽  
Moisture Dependence

AbstractThe dielectric constants of silica aerogels are among the lowest measured for any solid material. The silica aerogels also exhibit low thermal expansion and are thermally stable to temperatures exceeding 500°C. However, due to the open porosity and large surface areas for aerogels, their dielectric constants are strongly affected by moisture and temperature. This paper presents data for the dielectric constants of silica aerogels as a function of moisture content at 25 °C, and as a function of temperature, for temperatures in the range from 25 °C to 450°C. Dielectric constant data are also given for silica aerogels that are heat treated in dry nitrogen at 500°C, then cooled to 25°C for measurements in dry air. All measurements are made on bulk aerogel spheres at 22GHz microwave frequency, using a cavity perturbation method. The results of the dependence found here for bulk materials can be inferred to apply also to thin films of silica aerogels having similar nano-structures and densities.

scholarly journals Silica Aerogel: An Intrinsically Low Dielectric Constant Material

1995 ◽  
Vol 381 ◽  
Author(s):  
Lawrence W. Hrubesh
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Solid Material ◽  
Dielectric Strength ◽  
Silica Aerogels ◽  
Dielectric Constants ◽  
Porous Solids ◽  
Direct Result ◽  
Low Dielectric ◽  
Normal Transport

AbstractSilica aerogels are highly porous solids having unique morphologies in which both the pores and particles have sizes less than the wavelength of visible light. This fine nanostructure modifies the normal transport mechanisms within aerogels and endows them with a variety of exceptional physical properties. For example, aerogels have the lowest measured thermal conductivity and dielectric constant for any solid material. The intrinsically low dielectric properties of silica aerogels are the direct result of the extremely high achievable porosities, which are controllable over a range from 75% to more than 99.8%, and which result in measured dielectric constants from 2.0 to less than 1.01. This paper discusses the synthesis of silica aerogels, processing them as thin films, and characterizing their dielectric properties. Existing data and other physical characteristics of bulk aerogels (e.g., thermal stablity, thermal expansion, moisture adsorption, modulus, dielectric strength, etc.), which are useful for evaluating them as potential dielectrics for microelectronics, are also given.

Dielectric properties of aerogels

1993 ◽  
Vol 8 (7) ◽  
pp. 1736-1741 ◽  
Author(s):  
L.W. Hrubesh ◽  
L.E. Keene ◽  
V.R. Latorre
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Bulk Material ◽  
Solid Material ◽  
Adsorbed Water ◽  
Dielectric Behavior ◽  
Dielectric Constants ◽  
High Porosity ◽  
Microwave Frequencies ◽  
Low Dielectric

We have measured the real (dielectric constant) and imaginary (loss factor) components of the complex relative permittivity at 298 K using microwave frequencies (2, 10, and 18–40 GHz) for bulk SiO2-aerogels and for two types of organic aerogels, resorcinol-formaldehyde (RF) and melamine-formaldehyde (MF). Measured dielectric constants are found to vary linearly between values of 1.0 and 2.0 for aerogel densities from 10 to 500 kg/m3. For the same range of densities, the measured loss tangents vary linearly between values of 2 × 10−4 and 7 × 10−2. The observed linearity of the dielectric properties with density in aerogels at microwave frequencies shows that their dielectric behavior is more gas-like than solid-like. The dielectric properties of aerogels are shown to be significantly affected by the adsorbed water internal to the bulk material. For example, water accounts for 70% of the dielectric constant and 70% of the loss at microwave frequencies for silica aerogels. Because of their very high porosity, even with the water content, the aerogels are among the few materials exhibiting such low dielectric properties. Our measurements show that aerogels with greater than 99% porosity have dielectric constants less than 1.03; these are the lowest values ever reported for a bulk solid material.

Microstructure and Dielectric Properties of Heat-Treated SiC-AlN Multiphase Ceramics

2006 ◽  
Vol 313 ◽  
pp. 13-18 ◽  
Author(s):  
Xiao Mei Shi ◽  
Jian Hua Yang ◽  
Yu Bai Pan ◽  
Jing Kun Guo
Keyword(s):  
Solid Solution ◽  
Dielectric Properties ◽  
Annealing Temperature ◽  
Microwave Frequency ◽  
Dissipation Factor ◽  
Dielectric Constants ◽  
X Ray Diffraction ◽  
Sintering Additive ◽  
Heat Treated ◽  
Multiphase Ceramics

Silicon carbide is widely used as an important structural material. It is known for its extreme hardness, high temperature antioxygenic properties and good tribological properties. Moreover, SiC is also an intrinsic semiconductor. SiC can react with AlN and form an extensive solid solution at temperatures between 1800 to 21000C, and has excellent mechanical properties. However, in this article, we study the influence of the microstructure and the dielectric properties of SiC ceramics. SiC-AlN solid-solution ceramics were prepared by hot-pressed sintering using Y2O3 as the sintering additive. The size of SiC and AlN powders were 0.6μm and 1.06µm respectively. The content of AlN starting powders was 14vol%. The hot-processing sintered SiC-AlN multiphase ceramics have reached high density at 1950oC in Ar atmosphere under 30MPa.The hot-processed ceramics were subjected to thermal treatments in a range of temperatures between 11000C and 16000C for 3hr. The grain size increased with the annealing temperature. X-ray diffraction profiles show that phase relationships. Scanning electron microscopy (SEM)) was used to determine fracture surface and the local compositions. Dielectric permittivities and dissipation factor of SiC-AlN composites were investigated with the varieties of annealing temperature and the content of AlN particles. Dielectric constants (ε) and Dielectric loss tangents (tanδ) were measured within the microwave frequency range from 40Hz to10MHz.

Application of Hydrophobic Silica/Fiber Composite Aerogels in Organic Absorption

2011 ◽  
Vol 675-677 ◽  
pp. 1035-1039 ◽  
Author(s):  
Wei Wei ◽  
Chen Wei Li ◽  
Ji Min Xie ◽  
Jian Jun Zhu ◽  
Xiao Meng Lü ◽  
...  
Keyword(s):  
Fiber Composite ◽  
Sol Gel ◽  
Polypropylene Fiber ◽  
Solid Material ◽  
Silica Aerogels ◽  
Silica Fiber ◽  
Organic Liquids ◽  
Practical Applications ◽  
Surface Areas ◽  
Composite Aerogels

SiO2aerogels, the lightest solid material have attracted much attention recently. However, it is difficult to be used in practical applications due to its fragility. A facile one step polymerincorporation sol-gel process, together with a surface modification and a normal temperature drying process, was developed to prepare silica-fiber composite aerogels. Four fibers (polyester fiber, polypropylene fiber, lignin fiber, polycrylonitrile fiber) were selected to enhance the intensity of silica aerogels, respectively. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) specific surface area. Results showed that samples have a plenty of hydrophobic methyl group attached to their surface. The continuous network structure composed of silica aerogels of high purity are non-crystallized, porous, surface areas from 800 to 980 m2/g and light weight nano-materials. Adsorption experiment of the above samples over organic solution (benzene, toluene) was tested. The composite aerogels absorbed the organic liquids by nearly 6-8 times its own mass, showing potential application in organic absorption.

scholarly journals Synthesis and characterization of Mg–Zn ferrite based flexible microwave composites and its application as SNG metamaterial

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Md Atiqur Rahman ◽  
Mohammad Tariqul Islam ◽  
Mandeep Singh Jit Singh ◽  
Md Samsuzzaman ◽  
Muhammad E. H. Chowdhury
Keyword(s):  
Low Cost ◽  
Sol Gel ◽  
Microwave Frequency ◽  
Dielectric Substrate ◽  
Dielectric Constants ◽  
Potential Candidate ◽  
Flexible Composites ◽  
Average Grain Size ◽  
Zn Ferrite ◽  
High Flexibility

AbstractIn this article, we propose SNG (single negative) metamaterial fabricated on Mg–Zn ferrite-based flexible microwave composites. Firstly, the flexible composites are synthesized by the sol-gel method having four different molecular compositions of MgxZn(1−x)Fe2O4, which are denoted as Mg20, Mg40, Mg60, and Mg80. The structural, morphological, and microwave properties of the synthesized flexible composites are analyzed using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and conventional dielectric assessment kit (DAK) to justify their possible application as dielectric substrate at microwave frequency regime. Thus the average grain size is found from 20 to 24 nm, and the dielectric constants are 6.01, 5.10, 4.19, and 3.28, as well as loss tangents, are 0.002, 0.004, 0.006, and 0.008 for the prepared Mg–Zn ferrites, i.e., Mg20, Mg40, Mg60, and Mg80 respectively. Besides, the prepared low-cost Mg–Zn ferrite composites exhibit high flexibility and lightweight, which makes them a potential candidate as a metamaterial substrate. Furthermore, a single negative (SNG) metamaterial unit cell is fabricated on the prepared, flexible microwave composites, and their essential electromagnetic behaviors are observed. Very good effective medium ratios (EMR) vales are obtained from 14.65 to 18.47, which ensure the compactness of the fabricated prototypes with a physical dimension of 8 × 6.5 mm2. Also, the proposed materials have shown better performances comparing with conventional FR4 and RO4533 materials, and they have covered S-, C-, X-, Ku-, and K-band of microwave frequency region. Thus, the prepared, flexible SNG metamaterials on MgxZn(1−x)Fe2O4 composites are suitable for microwave and flexible technologies.

scholarly journals Comment on “investigation of dielectric constants of water in a nano-confined pore” by H. Zhu, F. Yang, Y. Zhu, A. Li, W. He, J. Huang and G. Li, RSC Adv., 2020, 10, 8628

RSC Advances ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 5179-5181
Author(s):  
Sayantan Mondal ◽  
Biman Bagchi
Keyword(s):  
Dielectric Constant ◽  
Dielectric Constants ◽  
Static Dielectric Constant ◽  
Inherent Anisotropy ◽  
Nanoconfined Water

Neglects of inherent anisotropy and distinct dielectric boundaries may lead to completely erroneous results. We demonstrate that such mistakes can give rise to gross underestimation of the static dielectric constant of cylindrically nanoconfined water.

A facile method to fabricate monolithic alumina–silica aerogels with high surface areas and good mechanical properties

2020 ◽  
Vol 40 (6) ◽  
pp. 2480-2488 ◽  
Author(s):  
Fei Peng ◽  
Yonggang Jiang ◽  
Junzong Feng ◽  
Liangjun Li ◽  
Huafei Cai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Surface ◽  
Silica Aerogels ◽  
Surface Areas ◽  
Monolithic Alumina

DIELECTRIC CONSTANT AND SEEBECK COEFFICIENT FOR SEMICONDUCTORS: THERMODYNAMIC AND DFT STUDIES

2013 ◽  
Vol 12 (06) ◽  
pp. 1350057 ◽  
Author(s):  
HSIU-YA TASI ◽  
CHAOYUAN ZHU
Keyword(s):  
Boundary Condition ◽  
Dielectric Constant ◽  
Seebeck Coefficient ◽  
Gas Phase ◽  
Present Method ◽  
Dielectric Constants ◽  
Semiconductor Materials ◽  
Electronic Polarizability ◽  
Seebeck Coefficients ◽  
Good Agreement

Dielectric constants and Seebeck coefficients for semiconductor materials are studied by thermodynamic method plus ab initio quantum density functional theory (DFT). A single molecule which is formed in semiconductor material is treated in gas phase with molecular boundary condition and then electronic polarizability is directly calculated through Mulliken and atomic polar tensor (APT) density charges in the presence of the external electric field. This electronic polarizability can be converted to dielectric constant for solid material through the Clausius–Mossotti formula. Seebeck coefficient is first simulated in gas phase by thermodynamic method and then its value divided by its dielectric constant is regarded as Seebeck coefficient for solid materials. Furthermore, unit cell of semiconductor material is calculated with periodic boundary condition and its solid structure properties such as lattice constant and band gap are obtained. In this way, proper DFT function and basis set are selected to simulate electronic polarizability directly and Seebeck coefficient through chemical potential. Three semiconductor materials Mg 2 Si , β- FeSi 2 and SiGe are extensively tested by DFT method with B3LYP, BLYP and M05 functionals, and dielectric constants simulated by the present method are in good agreement with experimental values. Seebeck coefficients simulated by the present method are in reasonable good agreement with experiments and temperature dependence of Seebeck coefficients basically follows experimental results as well. The present method works much better than the conventional energy band structure theory for Seebeck coefficients of three semiconductors mentioned above. Simulation with periodic boundary condition can be generalized directly to treat with doped semiconductor in near future.

scholarly journals Reduction of Electromagnetic Interference Using ZnO-PCL Nanocomposites at Microwave Frequency

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Abubakar Yakubu ◽  
Zulkifly Abbas ◽  
Nor Azowa Ibrahim ◽  
Ahmad Fahad
Keyword(s):  
Electromagnetic Interference ◽  
Electromagnetic Compatibility ◽  
Environmentally Friendly ◽  
Microwave Frequency ◽  
Absorption Properties ◽  
Radio Emissions ◽  
Surface Areas ◽  
Home Appliance ◽  
Coaxial Probe ◽  
Very High

In industrial equipment and home appliance applications, the electromagnetic compatibility compliance directive (ECCD) demands that electromagnetic interference side effects be eliminated or marginally minimized. The equipment must not disturb radio and telecommunication as well as other appliances. Additionally the ECCD also governs the immunity of such equipment to interference and seeks to ensure that this equipment is not disturbed by radio emissions when used as intended. Many types of absorbing materials are commercially available. However, many are expensive and not environmentally friendly. It is in the light of the above that we studied the electromagnetic absorption properties of ZnO-PCL nanocomposites prepared from cheap and abundant resources which are environmentally friendly (zinc and polycaprolactone). The test was carried out using a microstrip, open ended coaxial probe, and vector network analyzer. Amongst other findings, result showed that the ZnO-PCL nanocomposite has the capability of attenuating microwave frequency up to −18.2 dB due to their very high specific surface areas attributed to the nanofillers at 12 GHz.

scholarly journals A note on some further determinations of the dielectric constants of organic bodies and electrolytes at very low temperatures

1898 ◽  
Vol 62 (379-387) ◽  
pp. 250-266 ◽  
Keyword(s):  
Dielectric Constant ◽  
Low Temperatures ◽  
Tuning Fork ◽  
Dielectric Constants ◽  
The Past ◽  
Method Of Measurement ◽  
The Given ◽  
Past Summer

In several previous communications we have described the investigations made by us on the dielectric constants of various frozen organic bodies and electrolytes at very low temperatures. In these researches we employed a method for the measurement of the dielectric constant which consisted in charging and discharging a condenser, having the given body as dielectric, through a galvanometer 120 times in a second by means of a tuning-fork interrupter. During the past summer we have repeated some of these determinations and used a different method of measurement and a rather higher frequency. In the experiments here described we have adopted Nernst’s method for the measurement of dielectric constants, using for this purpose the apparatus as arranged by Dr. Nernst which belongs to the Davy-Faraday Laboratory.

Sign in / Sign up

Export Citation Format

Share Document