Low Dielectric Constant Fluorinated Polyimides for Interlayer Dielectric Applications

1997 ◽  
Vol 476 ◽  
Author(s):  
John Pellerin ◽  
Robert Fox ◽  
Huei-Min Ho
Keyword(s):  
Dielectric Constant ◽  
Electrical Performance ◽  
Low Dielectric Constant ◽  
Interlayer Dielectric ◽  
Metal Structures ◽  
Single Level ◽  
Low Dielectric ◽  
Fluorinated Polyimide ◽  
Fluorinated Polyimides ◽  
Low K

AbstractThis paper presents the results of development, characterization and integration screening of low dielectric constant (low k) fluorinated polyimides for interlayer dielectric applications. Evolution of these materials has progressed with the intent of improving fundamental thin film properties, such as thermal stress behavior, modulus, CTE, and dielectric constant. Further refinements to fluorinated polyimides have been to improve their process compatibility and integration characteristics, primarily in the area of deep sub-micron gap filling. The avenues taken to attain these objectives will be illustrated.Subsequent integration of low k fluorinated polyimides has been achieved for a completed single-level metal BEOL test vehicle to highlight the impacts of the film's adhesion, mechanical and thermomechanical properties. In addition, the completed fluorinated polyimide single-level metal structures have been used to characterize electrical performance in contrast to single-level metal structures with TEOS dielectric. Intralevel capacitance and leakage current have been measured with dual comb and serpentine structures. Modeling has been applied to verify dielectric constant in submicron geometries from the capacitance measurements.

Investigations of The Low Dielectric Constant Fluorinated Polyimide for Use as The Interlayer Dielectric in ULSI

1995 ◽  
Vol 381 ◽  
Author(s):  
Y.K. Lee ◽  
S.P. Murarka ◽  
S. -P. Jeng ◽  
B. Auman
Keyword(s):  
Thin Film ◽  
Dielectric Constant ◽  
Effect Of Temperature ◽  
Low Dielectric Constant ◽  
Flat Band ◽  
Flat Band Voltage ◽  
Interlayer Dielectric ◽  
Integrated Electronics ◽  
Low Dielectric ◽  
Fluorinated Polyimide

AbstractLow dielectric constant interlayer dielectric ( ILD) materials are required for the advanced silicon integrated electronics such as those in the ULSI era[3, 10]. We have investigated several such materials. In this paper the results of our investigations of the materials and electrical properties, processing ( to form ILD ), and applicability of a DuPont fluorinated polyimide are described and discussed. Weight loss, FTIR, and ellipsometric measurements have been carried out. The DuPont fluorinated polyimide thin film was observed to be thermally stable up to 450°C, which is monitored by using dynamic TGA with a ramping rate of 10°C/min or 5°C/min in N2 Ambient. Also MIPOS capacitor characterization, effect of temperature and moisture on these properties have been determined. The dielectric constant was observed to be as low as 2.5 and the refractive index is around 1.63, both being stable up to 450°C. However, the DuPont Fluorinated polyimide exhibited a flat band voltage shift on C-V curve after 400°C annealing in vacuum environments for 1 hr. Compatibility with copper as the interconnecting metal has been determined and discussed[8]. It is concluded that this polymer is a possible candidate for ILD application.

Novel Materials as Interlayer Low-K Dielectrics for CMOS Interconnect Applications

2011 ◽  
Vol 110-116 ◽  
pp. 5380-5383
Author(s):  
Tejas R. Naik ◽  
Veena R. Naik ◽  
Nisha P. Sarwade
Keyword(s):  
Dielectric Constant ◽  
Integrated Circuits ◽  
Dielectric Materials ◽  
Low Dielectric Constant ◽  
Interlayer Dielectric ◽  
Novel Materials ◽  
Low Dielectric ◽  
Processing Properties ◽  
New Generation ◽  
Low K

Scaling down the integrated circuits has resulted in the arousal of number of problems like interaction between interconnect, crosstalk, time delay etc. These problems can be overcome by new designs and by use of corresponding novel materials, which may be a solution to these problems. In the present paper we try to put forward very recent development in the use of novel materials as interlayer dielectrics (ILDs) having low dielectric constant (k) for CMOS interconnects. The materials presented here are porous and hybrid organo-inorganic new generation interlayer dielectric materials possessing low dielectric constant and better processing properties.

Material Properties of a SiOC Low Dielectric Constant Film with Extendibility to k < 2.7

2000 ◽  
Vol 612 ◽  
Author(s):  
Eugene S. Lopata ◽  
Lydia Young ◽  
John T. Felts
Keyword(s):  
Thermal Stability ◽  
Dielectric Constant ◽  
Material Properties ◽  
Low Dielectric Constant ◽  
Adhesion Properties ◽  
Interlayer Dielectric ◽  
Good Thermal Stability ◽  
Low Dielectric ◽  
Excellent Adhesion ◽  
Low K

AbstractA plasma deposited SiOC very low k (VLK) interlayer dielectric (ILD) film has been developed which can be tuned to 2.5 = k = 3.0, demonstrates very good thermal stability, excellent adhesion properties, acceptable hardness, and an indication that it may be extendible to k < 2.5. This paper will disclose properties of this SiOC film which are important to a VLK ILD application.

Structire, Properties, and Process Characteristics of Low-K Materials Prepared by PECVD

1999 ◽  
Vol 565 ◽  
Author(s):  
Y. Shimogaki ◽  
S. W. Lim ◽  
E. G. Loh ◽  
Y. Nakano ◽  
K. Tada ◽  
...  
Keyword(s):  
Growth Rate ◽  
Dielectric Constant ◽  
Gas Flow ◽  
Structural Changes ◽  
Silicon Oxide ◽  
Reactive Species ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Step Coverage ◽  
Low K

AbstractLow dielectric constant F-doped silicon oxide films (SiO:F) can be prepared by adding fluorine source, like as CF4 to the conventional PECVD processes. We could obtain SiO:F films with dielectric constant as low as 2.6 from the reaction mixture of SiH4/N2 O/CF4. The structural changes of the oxides were sensitively detected by Raman spectroscopy. The three-fold ring and network structure of the silicon oxides were selectively decreased by adding fluorine into the film. These structural changes contribute to the decrease ionic polarization of the film, but it was not the major factor for the low dielectric constant. The addition of fluorine was very effective to eliminate the Si-OH in the film and the disappearance of the Si-OH was the key factor to obtain low dielectric constant. A kinetic analysis of the process was also performed to investigate the reaction mechanism. We focused on the effect of gas flow rate, i.e. the residence time of the precursors in the reactor, on growth rate and step coverage of SiO:F films. It revealed that there exists two species to form SiO:F films. One is the reactive species which contributes to increase the growth rate and the other one is the less reactive species which contributes to have uniform step coverage. The same approach was made on the PECVD process to produce low-k C:F films from C2F4, and we found ionic species is the main precursor to form C:F films.

The characterization and preparation of porous low dielectric films using various cyclodextrins as template materials

2003 ◽  
Vol 766 ◽  
Author(s):  
Jin-Heong Yim ◽  
Jung-Bae Kim ◽  
Hyun-Dam Jeong ◽  
Yi-Yeoul Lyu ◽  
Sang Kook Mah ◽  
...  
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Dielectric Constant ◽  
Pore Structure ◽  
Pore Diameter ◽  
Dielectric Films ◽  
Low Dielectric Constant ◽  
Cyclodextrin Derivatives ◽  
Low Dielectric ◽  
Low K

AbstractPorous low dielectric films containing nano pores (∼20Å) with low dielectric constant (<2.2), have been prepared by using various kinds of cyclodextrin derivatives as porogenic materials. The pore structure such as pore size and interconnectivity can be controlled by changing functional groups of the cyclodextrin derivatives. We found that mechanical properties of porous low-k thin film prepared with mCSSQ (modified cyclic silsesquioxane) precursor and cyclodextrin derivatives were correlated with the pore interconnection length. The longer the interconnection length of nanopores in the thin film, the worse the mechanical properties of the thin film (such as hardness and modulus) even though the pore diameter of the films were microporous (∼2nm).

Low Dielectric Constant Materials for IC Intermetal Dielectric Applications: A Status Report on the Leading Candidates

1996 ◽  
Vol 443 ◽  
Author(s):  
Neil H. Hendricks
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Process Integration ◽  
Electrical Performance ◽  
Low Dielectric Constant ◽  
Status Report ◽  
Structure Property ◽  
Chemical Structures ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials

AbstractFor over two years, intensive efforts at SEMATECH and elsewhere have focused on identifying low dielectric constant (low ε) materials which possess all of the required properties and processing characteristics needed for integration into standard IC fabrication lines. To date, no material candidate has been shown to satisfy this impressive list of requirements. For some candidates, drawbacks related to material properties such as poor thermal stability or electrical performance have been identified; in other cases, problems in process integration, for example difficulties in patterning have stalled progress.In this paper, most of the current leading candidates for the low ε IC IMC application are identified and discussed. An attempt is made to correlate structure/property relationships in these materials with their relative attributes and deficiencies as they relate to the IMD application. Key differences in chemistry and property/processing characteristics are contrasted for low c silicon-oxygen polymers and for purely organic polymers. Novel dielectrics such as porous organic and inorganic thin films are also discussed in terms of their properties and associated process integration challenges. Since the needs for global planarization and low c IMD are occurring within roughly the same generation of minimum feature size (˜ 0.25 μm), the chemical mechanical polishing (CMP) of low dielectric constant thin films and/or of SiO2 layers deposited above them is briefly discussed. Both subtractive metalization and damascene processes are included, and the required low dielectric constant film properties and processing characteristics are contrasted for each process. Finally, the author's views on future trends in low dielectric constant materials development are presented, with an emphasis on identifying the types of chemical structures which may prove viable for this most demanding of all polymer film applications.

scholarly journals Fluorinated polyimide/POSS hybrid polymers with high solubility and low dielectric constant

2016 ◽  
Vol 34 (11) ◽  
pp. 1363-1372 ◽  
Author(s):  
Chen-yi Wang ◽  
Wen-tao Chen ◽  
Chang Xu ◽  
Xiao-yan Zhao ◽  
Jian Li
Keyword(s):  
Dielectric Constant ◽  
Low Dielectric Constant ◽  
High Solubility ◽  
Hybrid Polymers ◽  
Low Dielectric ◽  
Fluorinated Polyimide

Intrinsic low dielectric behaviour of a highly thermally stable Sr-based metal–organic framework for interlayer dielectric materials

2014 ◽  
Vol 2 (19) ◽  
pp. 3762-3768 ◽  
Author(s):  
Muhammad Usman ◽  
Cheng-Hua Lee ◽  
Dung-Shing Hung ◽  
Shang-Fan Lee ◽  
Chih-Chieh Wang ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Metal Organic Framework ◽  
Dielectric Materials ◽  
Low Dielectric Constant ◽  
Water Molecules ◽  
Compound A ◽  
Interlayer Dielectric ◽  
Low Dielectric ◽  
Metal Organic ◽  
Organic Framework

A Sr-based metal–organic framework exhibits an intrinsic low dielectric constant after removing the water molecules. A low dielectric constant and high thermal stability make this compound a candidate for use as a low-k material.

High-performance fluorinated polyimide/pure silica zeolite nanocrystal hybrid films with a low dielectric constant

RSC Advances ◽  
2015 ◽  
Vol 5 (93) ◽  
pp. 76476-76482 ◽  
Author(s):  
Zhenxun Huang ◽  
Shumei Liu ◽  
Yanchao Yuan ◽  
Jianqing Zhao
Keyword(s):  
Dielectric Constant ◽  
High Performance ◽  
Low Dielectric Constant ◽  
Hybrid Films ◽  
Low Dielectric ◽  
Simple Strategy ◽  
Pure Silica ◽  
Fluorinated Polyimide ◽  
Enhanced Properties

A simple strategy for preparing the low-κ FPI hybrids with enhanced properties.

Sign in / Sign up

Export Citation Format

Share Document