Epitaxial Batio3 and Knbo3 Thin Films On Various Substrates for Optical Waveguide Applications

1996 ◽  
Vol 441 ◽  
Author(s):  
L. Beckers ◽  
W. Zander ◽  
J. Schubert ◽  
P. Leinenbach ◽  
Ch. Buchal ◽  
...  
Keyword(s):  
Optical Materials ◽  
Rutherford Backscattering Spectrometry ◽  
X Ray Diffraction ◽  
Crystalline Perfection ◽  
Rocking Curve ◽  
X Ray ◽  
Flat Surfaces ◽  
Force Microscopy ◽  
Atomic Force ◽  
Yield Values

AbstractTechnologically interesting optical materials such as BaTiO3 and KnbO3 are difficult to grow as single crystals of large dimensions. Thin film techniques can overcome this problem by synthesizing these materials on commercially available substrates. We demonstrate the deposition of single crystalline BaTiO3 and KnbO3 on MgO, SrTiO3 and buffered MgO substrates by Pulsed Laser Deposition (PLD). The samples are characterized by Rutherford Backscattering Spectrometry / Channeling (RBS/C), X-Ray Diffraction (XRD) and Atomic Force Microscopy (AFM). We found excellent crystalline quality, confirmed by RBS/C minimum yield values of 2 % and a FWHM of 0.36° of the BaTiO3(002) rocking curve. Even films of a few microns thickness have been grown without loss of crystalline perfection, and all films show very flat surfaces. The RMS roughness of a 950 nm BaTiO3 film was found to be 1.1 nm.

Epitaxial BaTiO3 Thin Films on Different Substrates for Optical Waveguide Applications

1999 ◽  
Vol 597 ◽  
Author(s):  
M. Siegert ◽  
Judit G. Lisoni ◽  
C. H. Lei ◽  
A. Eckau ◽  
W. Zander ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Waveguides ◽  
Rutherford Backscattering Spectrometry ◽  
Optical Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Transmission Electron

AbstractIn the process of developing thin film electro-optical waveguides we investigated the influence of different substrates on the optical and structural properties of epitaxial BaTiO3 thin films. These films are grown by on-axis pulsed laser deposition (PLD) on MgO(100), MgAl2O4(100), SrTiO3(100) and MgO buffered A12O3(1102) substrates. The waveguide losses and the refractive indices were measured with a prism coupling setup. The optical data are correlated to the results of Rutherford backscattering spectrometry/ion channeling (RBS/C). X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). BaTiO3 films on MgO(100) substrates show planar waveguide losses of 3 dB/cm and ridge waveguide losses of 5 dB/cm at a wavelength of 633 nm.

Investigation Of Nucleation And Initial Stage Of Gan Growth By Atomic Force Microscopy And X-Ray Diffraction

1997 ◽  
Vol 482 ◽  
Author(s):  
P. W. Yip ◽  
S.-Q. Wang ◽  
A. J. Drehman ◽  
L. D. Zhu ◽  
P. E. Norris
Keyword(s):  
Atomic Force Microscopy ◽  
Surface Morphology ◽  
Deposition Temperature ◽  
Yellow Luminescence ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Initial Stage

AbstractThe nucleation and initial stage of GaN growth on sapphire was investigated by atomic force microscopy, X-ray diffraction and photoluminescence. A 15 to 30 nm thick GaN buffer layer deposited at proper conditions was extremely smooth and nearly amorphous. Proper post deposition annealing resulted in the buffer crystallized. The buffer layer deposition temperature, thickness and annealing time and temperature must be coordinated. Low deposition temperature and/or insufficient annealing of the buffer results in a GaN wafer which has fine spiking surface morphology with an RMS of 3.4 nm for 1.4 μm wafer, strong yellow luminescence and wide xray rocking curve FWHM. High deposition temperature, longer crystallization time, and a low growth rate results in a wafer which exhibits strong band edge luminescence without noticeable yellow luminescence, and a narrow (002) diffraction rocking curve. However, the surface morphology exhibits well developed hexagonal feature with RMS roughness of 14.3 nm for a 570 nm thick layer. X-ray rocking curve analysis revealed buffer crystallization, domain coalescence and alignment process. The FWHM of the ω–scan of GaN (101) diffraction was 1700–2000 arc seconds for 200–1400 nm wafers which indicates that the twist of the domains is not changing much with the growth.

Stress origin and relaxation in epitaxial AlN thin films on SiC

2001 ◽  
Vol 696 ◽  
Author(s):  
Ravi Bathe ◽  
R.D. Vispute ◽  
Daniel Habersat ◽  
R. P. Sharma ◽  
T. Venkatesan ◽  
...  
Keyword(s):  
Thin Films ◽  
Rutherford Backscattering Spectrometry ◽  
Wide Band ◽  
X Ray Diffraction ◽  
Wide Band Gap ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Highly Strained

AbstractWe have investigated the epitaxy, surfaces, interfaces, and defects in AlN thin films grown on SiC by pulsed laser deposition. The stress origin, evolution, and relaxation in these films is reported. The crystalline structure and surface morphology of the epitaxially grown AlN thin films on SiC (0001) substrates have been studied using x-ray diffraction (θ–2θ, ω, and Ψ scans) and atomic force microscopy, respectively. The defect analysis has been carried out by using Rutherford backscattering spectrometry and ion channeling technique. The films were grown at various substrate temperatures ranging from room temperature to 1100 °C. X-ray diffraction measurements show highly oriented AlN films when grown at temperatures of 750- 800 °C, and single crystals above 800 °C. The films grown in the temperature range of 950 °C to 1000 °C have been found to be highly strained, whereas the films grown above 1000 °C were found to be cracked along the crystallographic axes. The results of stress as a function of growth temperature, thermal mismatch, growth mode, and buffer layer thickness will be presented, and the implications of these results for wide band gap power electronics will be discussed.

Increased Growth Rates of 3C-SiC on Si (100) Substrates via HCl Growth Additive

2007 ◽  
Vol 556-557 ◽  
pp. 191-194 ◽  
Author(s):  
M. Reyes ◽  
Y. Shishkin ◽  
S. Harvey ◽  
Stephen E. Saddow
Keyword(s):  
Growth Rates ◽  
Film Growth ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
Diffraction Plane ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Rate Versus ◽  
Sic Film

Growth rates from 10 to 38 μm/h of single crystal 3C-SiC on planar Si (001) substrates have been obtained in a low-pressure horizontal hot-wall CVD reactor. The propane-silanehydrogen gas chemistry system with HCl added as a growth additive, which allows an increased amount of silane to be introduced into the reactor during growth, was used. The 3C-SiC film growth rate versus silane mole fraction was found to be a linear function in the range from 0.43x10-3 to 1.50x10-3. Nomarski optical microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, atomic force microscopy and X-ray diffraction were used to characterize the deposited layers. The X-ray rocking curve taken on the (002) diffraction plane of a 12 μm thick 3CSiC (001) layer displayed a FWHM of 360 arcsec, which indicates the films are mono-crystalline.

Ultra-Smooth ZnO Buffer Layers on (001) Sapphire

1997 ◽  
Vol 482 ◽  
Author(s):  
A. J. Drehman ◽  
S.-Q. Wang ◽  
P. W. Yip
Keyword(s):  
Buffer Layers ◽  
Zno Films ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Force Microscopy ◽  
Sapphire Substrates ◽  
Atomic Force ◽  
Electrical Resistivities

AbstractUsing off-axis reactive rf sputtering, we have grown extremely smooth, nearly epitaxial, (001) oriented ZnO films on c-axis sapphire substrates. Atomic Force Microscopy was used to determine that these films are extremely smooth, having an rms roughness of only a few tenths of a nanometer. Based on high resolution x-ray diffraction (HXRD), the ZnO is highly oriented, with a rocking curve width of less than 400 arc seconds for the (006) diffraction peak, and only somewhat larger for the (112) reflection. HXRD Phi scans show that the ZnO (112) reflection is rotated in the a-b plane by 30 degrees from the sapphire (113) direction. These two measurements indicate excellent in-plane orientation. We are investigating the use of these buffer layers for subsequent GaN growth. Electrical resistivities of the films exceeded 100 kΩ-cm making ZnO a potential candidate as an insulating buffer layer.

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

Low Molecular Weight Microfibers with Light Sensing Properties

2017 ◽  
Vol 54 (4) ◽  
pp. 655-658
Author(s):  
Andrei Bejan ◽  
Dragos Peptanariu ◽  
Bogdan Chiricuta ◽  
Elena Bicu ◽  
Dalila Belei
Keyword(s):  
Molecular Weight ◽  
Low Molecular Weight ◽  
X Ray Diffraction ◽  
Aromatic Rings ◽  
X Ray ◽  
Force Microscopy ◽  
Light Sensing ◽  
Sensing Applications ◽  
Atomic Force ◽  
Low Molecular Weight Compounds

Microfibers were obtained from organic low molecular weight compounds based on heteroaromatic and aromatic rings connected by aliphatic spacers. The obtaining of microfibers was proved by scanning electron microscopy. The deciphering of the mechanism of microfiber formation has been elucidated by X-ray diffraction, infrared spectroscopy, and atomic force microscopy measurements. By exciting with light of different wavelength, florescence microscopy revealed a specific optical response, recommending these materials for light sensing applications.

Nanocrystalline Solutions as Precursors to The Spray Deposition of Cdte Thin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
Martin Pehnt ◽  
Douglas L. Schulz ◽  
Calvin J. Curtis ◽  
Helio R. Moutinho ◽  
Amy Swartzlander ◽  
...  
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Cdte Nanoparticles ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Cdte Thin Films

ABSTRACTIn this article we report the first nanoparticle-derived route to smooth, dense, phase-pure CdTe thin films. Capped CdTe nanoparticles were prepared by injection of a mixture of Cd(CH3)2, (n-C8H17)3 PTe and (n-C8H17)3P into (n-C8H17)3PO at elevated temperatures. The resultant nanoparticles 32-45 Å in diameter were characterized by x-ray diffraction, UV-Vis spectroscopy, transmission electron microscopy, thermogravimetric analysis and energy dispersive x-ray spectroscopy. CdTe thin film deposition was accomplished by dissolving CdTe nanoparticles in butanol and then spraying the solution onto SnO2-coated glass substrates at variable susceptor temperatures. Smooth and dense CdTe thin films were obtained using growth temperatures approximately 200 °C less than conventional spray pyrolysis approaches. CdTe films were characterized by x-ray diffraction, UV-Vis spectroscopy, atomic force microscopy, and Auger electron spectroscopy. An increase in crystallinity and average grain size as determined by x-ray diffraction was noted as growth temperature was increased from 240 to 300 °C. This temperature dependence of film grain size was further confirmed by atomic force microscopy with no remnant nanocrystalline morphological features detected. UV-Vis characterization of the CdTe thin films revealed a gradual decrease of the band gap (i.e., elimination of nanocrystalline CdTe phase) as the growth temperature was increased with bulk CdTe optical properties observed for films grown at 300 °C.

Frequency and Temperature Dependence of Dielectric Properties of Orthorhombic HoMnO3 Thin Films

2014 ◽  
Vol 1025-1026 ◽  
pp. 427-431
Author(s):  
Ping Gao ◽  
Wei Zhang ◽  
Wei Tian Wang
Keyword(s):  
Dielectric Properties ◽  
Pulsed Laser ◽  
Signal Amplitude ◽  
Debye Model ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Cole Diagram

Orthorhombic HoMnO3 films were prepared epitaxially on Nb-doped SrTiO3 single crystal substrates by using pulsed laser deposition technique. The films showed perfectly a-axis crystallographic orientations. X-ray diffraction and atomic force microscopy were used to characterize the films. The complex dielectric properties were measured as functions of frequency (40 Hz~1 MHz) and temperature (80 K~300 K) with a signal amplitude of 50 mv. The respective dielectric relaxation peaks shifted to higher frequency as the measuring temperature increased, with the same development of real part of the complex permittivity. The cole-cole diagram was obtained according to the Debye model, and the effects of relaxation process were discussed.

Sign in / Sign up

Export Citation Format

Share Document