Nanoscale Modification Of Amorphous Diamond-Like Carbon Film Surfaces

1995 ◽  
Vol 416 ◽  
Author(s):  
T. W. Mercer ◽  
N. J. Dinardo ◽  
J. P. Sullivan ◽  
T. A. Friedmann ◽  
M. P. Siegal ◽  
...  
Keyword(s):  
Carbon Film ◽  
Carbon Films ◽  
Scanning Tunneling ◽  
Plasmon Energy ◽  
Electron Dose ◽  
Force Microscopy ◽  
Spatially Resolved ◽  
Atomic Force ◽  
Potential Applications ◽  
Electron Energy Loss

ABSTRACTScanning Tunneling and Atomic Force Microscopy (STM, AFM) of amorphous tetrahedral carbon films (a-tC) film surfaces grown by pulsed laser deposition indicate extreme flatness and uniform electronic properties.1 This is consistent with the observed predominance of sp3 (diamond-like) bonding in these materials.2 Potential applications of a-tC films may be enhanced with the ability to modify their surfaces on the nanoscale. Exploiting the metastable nature of the sp3 hybridized state of carbon, the high flux electron beam from an STM tip was used to modify ˜100 nm regions; processing in air or in vacuum produces similar results. STM and AFM maps of the modified regions indicate stable morphologic and electronic structures consistent with a local transformation to sp2 (graphitic) hybridization. Surface potentiometric mapping of these regions indicates a correlation between electron dose and a lowering of the surface potential. In addition, spatially-resolved electron energy loss spectroscopy of the modified areas performed with a Scanning Auger Microscope shows plasmon energy shifts that confirm an elevated sp2 content in the modified regions.3

Scanning tunneling microscopy and atomic force microscopy: New tools for biology

1989 ◽  
Vol 47 ◽  
pp. 778-779
Author(s):  
CE Bracker ◽  
P. K. Hansma
Keyword(s):  
Physical Property ◽  
Scanning Probe ◽  
Scanning Tunneling ◽  
Small Scale ◽  
Tunneling Microscopy ◽  
Force Microscopy ◽  
New Family ◽  
Small Probe ◽  
Atomic Force ◽  
Transmission Electron

A new family of scanning probe microscopes has emerged that is opening new horizons for investigating the fine structure of matter. The earliest and best known of these instruments is the scanning tunneling microscope (STM). First published in 1982, the STM earned the 1986 Nobel Prize in Physics for two of its inventors, G. Binnig and H. Rohrer. They shared the prize with E. Ruska for his work that had led to the development of the transmission electron microscope half a century earlier. It seems appropriate that the award embodied this particular blend of the old and the new because it demonstrated to the world a long overdue respect for the enormous contributions electron microscopy has made to the understanding of matter, and at the same time it signalled the dawn of a new age in microscopy. What we are seeing is a revolution in microscopy and a redefinition of the concept of a microscope.Several kinds of scanning probe microscopes now exist, and the number is increasing. What they share in common is a small probe that is scanned over the surface of a specimen and measures a physical property on a very small scale, at or near the surface. Scanning probes can measure temperature, magnetic fields, tunneling currents, voltage, force, and ion currents, among others.

Development of the UHV-STM

1990 ◽  
Vol 48 (1) ◽  
pp. 322-323
Author(s):  
M. Iwatsuki ◽  
S. Kitamura ◽  
A. Mogami
Keyword(s):  
Surface Science ◽  
Real Space ◽  
Atomic Scale ◽  
Scanning Tunneling ◽  
Great Promise ◽  
Force Microscopy ◽  
Atomic Force ◽  
Stm Image ◽  
Surface Construction ◽  
Very High

Since Binnig, Rohrer and associates observed real-space topographic images of Si(111)-7×7 and invented the scanning tunneling microscope (STM),1) the STM has been accepted as a powerful surface science instrument.Recently, many application areas for the STM have been opened up, such as atomic force microscopy (AFM), magnetic force microscopy (MFM) and others. So, the STM technology holds a great promise for the future.The great advantages of the STM are its high spatial resolution in the lateral and vertical directions on the atomic scale. However, the STM has difficulty in identifying atomic images in a desired area because it uses piezoelectric (PZT) elements as a scanner.On the other hand, the demand to observe specimens under UHV condition has grown, along with the advent of the STM technology. The requirment of UHV-STM is especially very high in to study of surface construction of semiconductors and superconducting materials on the atomic scale. In order to improve the STM image quality by keeping the specimen and tip surfaces clean, we have built a new UHV-STM (JSTM-4000XV) system which is provided with other surface analysis capability.

scholarly journals Exploring Intramolecular Methyl–Methyl Coupling on a Metal Surface for Edge-Extended Graphene Nanoribbons

2021 ◽  
Vol 03 (02) ◽  
pp. 128-133
Author(s):  
Zijie Qiu ◽  
Qiang Sun ◽  
Shiyong Wang ◽  
Gabriela Borin Barin ◽  
Bastian Dumslaff ◽  
...  
Keyword(s):  
Raman Spectroscopy ◽  
Atomic Force Microscopy ◽  
High Resolution ◽  
Graphene Nanoribbons ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Force Microscopy ◽  
Methyl Methyl ◽  
Atomic Force ◽  
Edge Extension

Intramolecular methyl–methyl coupling on Au (111) is explored as a new on-surface protocol for edge extension in graphene nanoribbons (GNRs). Characterized by high-resolution scanning tunneling microscopy, noncontact atomic force microscopy, and Raman spectroscopy, the methyl–methyl coupling is proven to indeed proceed at the armchair edges of the GNRs, forming six-membered rings with sp3- or sp2-hybridized carbons.

scholarly journals The Infuence of Salicin on Rheological and Film-Forming Properties of Collagen

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1661
Author(s):  
Katarzyna Adamiak ◽  
Katarzyna Lewandowska ◽  
Alina Sionkowska
Keyword(s):  
Mechanical Properties ◽  
Atomic Force Microscopy ◽  
Infrared Spectroscopy ◽  
Rheological Properties ◽  
Silver Carp ◽  
Shear Tests ◽  
Force Microscopy ◽  
Atomic Force ◽  
Film Forming ◽  
Potential Applications

Collagen films are widely used as adhesives in medicine and cosmetology. However, its properties require modification. In this work, the influence of salicin on the properties of collagen solution and films was studied. Collagen was extracted from silver carp skin. The rheological properties of collagen solutions with and without salicin were characterized by steady shear tests. Thin collagen films were prepared by solvent evaporation. The structure of films was researched using infrared spectroscopy. The surface properties of films were investigated using Atomic Force Microscopy (AFM). Mechanical properties were measured as well. It was found that the addition of salicin modified the roughness of collagen films and their mechanical and rheological properties. The above-mentioned parameters are very important in potential applications of collagen films containing salicin.

scholarly journals Local analysis of semiconductor nanoobjects by scanning tunneling atomic force microscopy

2015 ◽  
Vol 1 (1) ◽  
pp. 15-23 ◽  
Author(s):  
Natalia A. Lashkova ◽  
Nikita V. Permiakov ◽  
Alexander I. Maximov ◽  
Yulia M. Spivak ◽  
Vyacheslav A. Moshnikov
Keyword(s):  
Atomic Force Microscopy ◽  
Local Analysis ◽  
Scanning Tunneling ◽  
Force Microscopy ◽  
Atomic Force

SCANNING PROBE MICROSCOPY BASED NANOSCALE PATTERNING AND FABRICATION

COSMOS ◽  
2007 ◽  
Vol 03 (01) ◽  
pp. 1-21 ◽  
Author(s):  
XIAN NING XIE ◽  
HONG JING CHUNG ◽  
ANDREW THYE SHEN WEE
Keyword(s):  
Integrated Circuits ◽  
Scanning Probe Microscopy ◽  
Scanning Probe ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Force Microscopy ◽  
Nanoscale Patterning ◽  
Atomic Force ◽  
Probe Microscope ◽  
Molecular Manipulation

Nanotechnology is vital to the fabrication of integrated circuits, memory devices, display units, biochips and biosensors. Scanning probe microscope (SPM) has emerged to be a unique tool for materials structuring and patterning with atomic and molecular resolution. SPM includes scanning tunneling microscopy (STM) and atomic force microscopy (AFM). In this chapter, we selectively discuss the atomic and molecular manipulation capabilities of STM nanolithography. As for AFM nanolithography, we focus on those nanopatterning techniques involving water and/or air when operated in ambient. The typical methods, mechanisms and applications of selected SPM nanolithographic techniques in nanoscale structuring and fabrication are reviewed.

Measurement of Plasticity Gradients with Scanning Probe Microscopy

1993 ◽  
Vol 318 ◽  
Author(s):  
James D. Kiely ◽  
Dawn A. Bonnell
Keyword(s):  
Fracture Surface ◽  
Scanning Probe Microscopy ◽  
Scanning Probe ◽  
Scanning Tunneling ◽  
Ceramic System ◽  
Force Microscopy ◽  
Metal Fracture ◽  
Atomic Force ◽  
Metal Ceramic

ABSTRACTScanning Tunneling and Atomic Force Microscopy were used to characterize the topography of fractured Au /sapphire interfaces. Variance analysis which quantifies surface morphology was developed and applied to the characterization of the metal fracture surface of the metal/ceramic system. Fracture surface features related to plasticity were quantified and correlated to the fracture energy and energy release rate.

Preparation and Characterization of Chitosan-Casein Phosphopeptides Biocomposite Coatings on the Medical Titanium Alloy

2011 ◽  
Vol 480-481 ◽  
pp. 1065-1069
Author(s):  
Bin Liu ◽  
Lin Wang ◽  
Yin Zhong Bu ◽  
Sheng Rong Yang ◽  
Jin Qing Wang
Keyword(s):  
Photoelectron Spectroscopy ◽  
Attenuated Total Reflectance ◽  
Ti Alloy ◽  
Force Microscopy ◽  
Implant Materials ◽  
Atomic Force ◽  
Casein Phosphopeptides ◽  
Potential Applications ◽  
First Time

Titanium (Ti) and its alloys have been applied in orthopedics as one of the most popular biomedical metallic implant materials. In this work, to enhance the bioactivity, the surface of Ti alloy pre-modified by silane coupling agent and glutaraldehyde was covalently grafted with chitosan (CS) via biochemical multistep self-assembled method. Then, for the first time, the achieved surface was further immobilized with casein phosphopeptides (CPP), which are one group of bioactive peptides released from caseins in the digestive tract and can facilitate the calcium adsorption and usage, to form CS-CPP biocomposite coatings. The structure and composition of the fabricated coatings were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and atomic force microscopy (AFM). As the experimental results indicated, multi-step assembly was successfully performed, and the CS and CPP were assembled onto the Ti alloy surface orderly. It is anticipated that the Ti alloys modified by CS-CPP biocomposite coatings will find potential applications as implant materials in biomedical fields.

Sign in / Sign up

Export Citation Format

Share Document