Heteroepitaxial Growth of Epitaxial C60-Thin Films on Mica(001)

1994 ◽  
Vol 359 ◽  
Author(s):  
S. Henke ◽  
K.H. Thürer ◽  
S. Geier ◽  
B. Rauschenbach ◽  
B. Stritzker
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Substrate Temperature ◽  
Room Temperature ◽  
Heteroepitaxial Growth ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Substrate Temperatures

ABSTRACTOn mica(001) thin C60-films are deposited by thermal evaporation at substrate temperatures from room temperature up to 225°C. The dependence of the structure and the epitaxial alignment of the thin C60-films on mica(001) on the substrate temperature and the film thickness up to 1.3 μm at a well-defined deposition rate (0.008 nm/s) is investigated by atomic force microscopy and X-ray diffraction. The shape and the size of the C60-islands, which have an influence on the film quality at larger film thicknesses, are sensitively dependent on the substrate temperature. At a film thickness of 200 nm the increase of the substrate temperature up to 225°C leads to smooth, completely coalesced epitaxial C60-thin films characterized by a roughness smaller than 1.5 nm, a mosaic spread Δω of 0.1° and an azimuthal alignment ΔΦ of 0.45°.

Reactive Sputtering Growth and Characterizations of InN Thin Films on Si Substrates

2012 ◽  
Vol 545 ◽  
pp. 290-293
Author(s):  
Maryam Amirhoseiny ◽  
Hassan Zainuriah ◽  
Ng Shashiong ◽  
Mohd Anas Ahmad
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rf Power ◽  
X Ray Diffraction ◽  
Nitrogen Gas ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force

We have studied the effects of deposition conditions on the crystal structure of InN films deposited on Si substrate. InN thin films have been deposited on Si(100) substrates by reactive radio frequency (RF) magnetron sputtering method with pure In target at room temperature. The nitrogen gas pressure, applied RF power and the distance between target and substrate were 2×10-2 Torr, 60 W and 8 cm, respectively. The effects of the Ar–N2 sputtering gas mixture on the structural properties of the films were investigated by using scanning electron microscope, energy-dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction techniques.

Growth of heteroepitaxial GaSb thin films on Si(100) substrates

2004 ◽  
Vol 19 (8) ◽  
pp. 2315-2321 ◽  
Author(s):  
Thang Nguyen ◽  
Walter Varhue ◽  
Edward Adams ◽  
Mark Lavoie ◽  
Stephen Mongeon
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Lattice Mismatch ◽  
Stacking Faults ◽  
Heteroepitaxial Growth ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Radio Frequency Sputtering ◽  
Atomic Force ◽  
Transmission Electron

The heteroepitaxial growth of GaSb thin films on Si(100) and GaAs(100) substrates is presented. The growth technique involves the use of atomic Ga and Sb species, which are provided by thermal effusion and radio frequency sputtering, respectively. The crystalline quality of the heteroepitaxial GaSb film on the Si substrate is high despite the larger lattice mismatch. Epitaxial quality is determined by high-resolution x-ray diffraction and Rutherford backscatter spectrometry channeling. Atomic-force microscopy is used to monitor the evolution of surface morphology with increasing film thickness. Transmission electron microscopy shows the formation of stacking faults at the Si/GaSb interface and their eventual annihilation with increasing GaSb film thickness. Annihilation of stacking faults occurs when two next-neighbor mounds meet during the overgrowth of a common adjacent mound.

SURFACE MORPHOLOGY AND PHOTOLUMINESCENCE CHARACTERISTICS OF Sm-DOPED YVO4 THIN FILMS

2007 ◽  
Vol 14 (05) ◽  
pp. 873-878 ◽  
Author(s):  
HYUN KYOUNG YANG ◽  
JONG WON CHUNG ◽  
BYUNG KEE MOON ◽  
BYUNG CHUN CHOI ◽  
JUNG HYUN JUNG ◽  
...  
Keyword(s):  
Thin Films ◽  
Surface Morphology ◽  
Substrate Temperature ◽  
Photoluminescence Intensity ◽  
Photoluminescence Spectra ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Zircon Structure ◽  
Substrate Temperatures

Surface morphology and crystallinity of YVO 4: Sm 3+ thin films have an influence on the photoluminescence characteristics. The YVO 4: Sm 3+ films have been deposited on Al 2 O 3 (0001) substrates using pulsed laser deposition method. The films were grown at the various substrate temperatures changing from 500 to 700°C. The crystallinity and surface morphology of the films were investigated using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. The results of XRD showed that YVO 4: Sm 3+ films had a zircon structure and AFM study revealed that the films consisted of homogeneous grains ranging from 100 to 400 nm depending on the deposition conditions. The photoluminescence spectra were measured at room temperature and the emitted radiation was dominated by the red emission peak at 620 nm radiated from the transition of 5 D 0-7 F 2. The crystallinity, surface morphology, and photoluminescence spectra of thin-film phosphors were highly dependent on the substrate temperature. The surface roughness and photoluminescence intensity of the films showed similar behavior as a function of substrate temperature.

Preparation of Cu(In,Ga)Se2 thin films at low substrate temperatures

2001 ◽  
Vol 16 (2) ◽  
pp. 394-399 ◽  
Author(s):  
S. Nishiwaki ◽  
T. Satoh ◽  
Y. Hashimoto ◽  
T. Negami ◽  
T. Wada
Keyword(s):  
Thin Films ◽  
Surface Composition ◽  
Soda Lime ◽  
Soda Lime Glass ◽  
X Ray Diffraction ◽  
Monitoring Method ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Substrate Temperatures

Cu(In,Ga)Se2(CIGS) thin films were prepared at substrate temperatures of 350 to 500 °C. The (In,Ga)2Se2 precursor layers were deposited on Mo coated soda-lime glass and then exposed to Cu and Se fluxes to form CIGS films. The surface composition was probed by a real-time composition monitoring method. The CIGS films were characterized by x-ray diffraction, energy dispersive x-ray spectroscopy, secondary ion mass spectroscopy, and atomic force microscopy. The transient formation of a Cu–Se phase with a high thermal emissivity was observed during the deposition of Cu and Se at a substrate temperature of 350 °C. Faster diffusion of In than Ga from the (In,Ga)2Se3 precursor to the newly formed CIGS layer was observed. A growth model for CIGS films during the deposition of Cu and Se onto (In,Ga)2Se3 precursor is proposed. A solar cell using a CIGS film prepared at about 350 °C showed an efficiency of 12.4%.

Influence of Substrate Temperature on Structure and Optical Property of Cu3N Thin Films

2010 ◽  
Vol 152-153 ◽  
pp. 218-221
Author(s):  
Jian Rong Xiao ◽  
Ai Hua Jiang ◽  
Ye Guang Liang
Keyword(s):  
Thin Films ◽  
Substrate Temperature ◽  
Optical Transmission ◽  
X Ray Diffraction ◽  
Compact Structure ◽  
Copper Nitride ◽  
X Ray ◽  
Atomic Force ◽  
Influence Of Substrate ◽  
Substrate Temperatures

Copper nitride thin films were prepared by reactive radio frequency magnetron sputtering at various substrate temperatures. The surface morphology and crystal structure of the thin films were characterized by atomic force microscope (AFM) and X-ray diffraction (XRD), respectively. The AFM images demonstrate that the films have a compact structure. The XRD test indicates that growth orientation of the thin films prefers the (111) or (100) at different substrate temperature. The optical transmission properties of the thin films were obtained by an ultraviolet visible spectrometer. The optical band gap of the thin films decreases with increasing substrate temperature.

PREPARATION AND CHARACTERISTICS OF Sm-DOPED Bi2Ti2O7 THIN FILMS

2007 ◽  
Vol 14 (01) ◽  
pp. 147-150 ◽  
Author(s):  
DONGMEI YANG ◽  
CHANGHONG YANG ◽  
CHUNXUE YUAN ◽  
XIN YIN ◽  
JIANRU HAN
Keyword(s):  
Thin Films ◽  
Chemical Solution Deposition ◽  
Room Temperature ◽  
Chemical Solution ◽  
X Ray Diffraction ◽  
Solution Deposition ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Dielectric Constant And Loss

Crack-free Sm-doped Bi 2 Ti 2 O 7( Sm : Bi 2 Ti 2 O 7) thin films with a strong (111) orientation have been prepared on p-Si (111) by chemical solution deposition (CSD). The structural properties and crystallizations were studied by X-ray diffraction. The surface morphology and quality were examined using atomic force microscopy (AFM). The dielectric constant and loss factor at different frequencies were also evaluated at room temperature. Their insulation was studied, too. The films exhibit better insulating property than does the pure Bi 2 Ti 2 O 7.

Nanocrystalline Solutions as Precursors to The Spray Deposition of Cdte Thin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
Martin Pehnt ◽  
Douglas L. Schulz ◽  
Calvin J. Curtis ◽  
Helio R. Moutinho ◽  
Amy Swartzlander ◽  
...  
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Cdte Nanoparticles ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Cdte Thin Films

ABSTRACTIn this article we report the first nanoparticle-derived route to smooth, dense, phase-pure CdTe thin films. Capped CdTe nanoparticles were prepared by injection of a mixture of Cd(CH3)2, (n-C8H17)3 PTe and (n-C8H17)3P into (n-C8H17)3PO at elevated temperatures. The resultant nanoparticles 32-45 Å in diameter were characterized by x-ray diffraction, UV-Vis spectroscopy, transmission electron microscopy, thermogravimetric analysis and energy dispersive x-ray spectroscopy. CdTe thin film deposition was accomplished by dissolving CdTe nanoparticles in butanol and then spraying the solution onto SnO2-coated glass substrates at variable susceptor temperatures. Smooth and dense CdTe thin films were obtained using growth temperatures approximately 200 °C less than conventional spray pyrolysis approaches. CdTe films were characterized by x-ray diffraction, UV-Vis spectroscopy, atomic force microscopy, and Auger electron spectroscopy. An increase in crystallinity and average grain size as determined by x-ray diffraction was noted as growth temperature was increased from 240 to 300 °C. This temperature dependence of film grain size was further confirmed by atomic force microscopy with no remnant nanocrystalline morphological features detected. UV-Vis characterization of the CdTe thin films revealed a gradual decrease of the band gap (i.e., elimination of nanocrystalline CdTe phase) as the growth temperature was increased with bulk CdTe optical properties observed for films grown at 300 °C.

Optical properties of anatase TiO2 films modified by N ion implantation

2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu
Keyword(s):  
Thin Films ◽  
Ion Implantation ◽  
Photoelectron Spectroscopy ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Light Region ◽  
Uv Visible ◽  
Substrate Temperatures

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.

scholarly journals Influence of the growth parameters of TiO2 thin films deposited by the MOCVD method

Cerâmica ◽  
2002 ◽  
Vol 48 (305) ◽  
pp. 38-42 ◽  
Author(s):  
M. I. B. Bernardi ◽  
E. J. H. Lee ◽  
P. N. Lisboa-Filho ◽  
E. R. Leite ◽  
E. Longo ◽  
...  
Keyword(s):  
Thin Films ◽  
Growth Parameters ◽  
Structural Characteristics ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Tio2 Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Deposition Parameters

The synthesis of TiO2 thin films was carried out by the Organometallic Chemical Vapor Deposition (MOCVD) method. The influence of deposition parameters used during growth on the final structural characteristics was studied. A combination of the following experimental parameters was studied: temperature of the organometallic bath, deposition time, and temperature and substrate type. The high influence of those parameters on the final thin film microstructure was analyzed by scanning electron microscopy with electron dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction.

Sign in / Sign up

Export Citation Format

Share Document