Solid-Phase Epitaxial Regrowth of Ion-Implanted Silicon on Sapphire Using Rapid Thermal Annealing

1984 ◽  
Vol 35 ◽  
Author(s):  
A M Hodge ◽  
A G Cullis ◽  
N G Chew
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
Silicon Film ◽  
Silicon On Insulator ◽  
Full Potential ◽  
Cross Sectional ◽  
Epitaxial Regrowth ◽  
Transmission Electron ◽  
Device Processing

ABSTRACTSolid phase epitaxial regrowth of silicon on sapphire is used to improve the quality of as-received silicon films prior to conventional device processing. It has been shown that this is necessary, especially for layers of 0.3μm and thinner, if the full potential of this particular silicon on insulator technology is to be realised. Si+ ions are implanted at an energy and dose such that all but the surface of the silicon film is rendered amorphous. In this study, the layer is regrown using a rapid thermal annealer operated in the multi-second regime. A second shallower implant followed by rapid thermal annealing produces a further improvement. Characterisation of the material has been principally by cross-sectional transmission electron microscopy. The structures observed after different implant and regrowth treatments are discussed.

Observation of the Wurtzite Phase in OMVPE Grown ZnSe/GaAs: Effect on Implantation and Rapid Thermal Annealing

1989 ◽  
Vol 147 ◽  
Author(s):  
K. S. Jones ◽  
J. Yu ◽  
P. D. Lowen ◽  
D. Kisker
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Electrical Transport ◽  
High Resistivity ◽  
Ion Milling ◽  
Electrical Transport Properties ◽  
Wurtzite Phase ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Diffraction Patterns

AbstractTransmission electron diffraction patterns of cross-sectional TEM samples of OMVPE ZnSe on GaAs indicate the existence of the hexagonal wurtzite phase in the epitaxial layers. The orientation relationship is (0002)//(111); (1120)//(220). Etching studies indicate the phase is internal not ion milling induced. The average wurtzite particle size is 80Å-120Å. Because of interplanar spacing matches it is easily overlooked. Electrical property measurements show a high resistivity (1010ω/square) which drops by four orders of magnitude upon rapid thermal annealing between 700°C and 900 °C for 3 sec. Implantation of Li and N have little effect on the electrical transport properties. The Li is shown to have a high diffusivity, a solid solubility of ≈1016/cm3 at 800°C and getters to the ZnSeA/aAs interface.

Evolution of Epitaxial SixGei1-x Alloys on Si(100) During Thermal Annealing a-Ge/Au Bilayers Deposited on Si Substrate

1992 ◽  
Vol 280 ◽  
Author(s):  
Z. Ma ◽  
L. H. Allen
Keyword(s):  
Single Crystal ◽  
Thermal Annealing ◽  
Rutherford Backscattering Spectrometry ◽  
Solid Phase ◽  
Growth Dynamics ◽  
X Ray Diffraction ◽  
Si Substrate ◽  
Cross Sectional ◽  
X Ray ◽  
Transmission Electron

ABSTRACTSolid phase epitaxial (SPE) growth of SixGei1-x alloys on Si (100) was achieved by thermal annealing a-Ge/Au bilayers deposited on single crystal Si substrate in the temperature range of 280°C to 310°C. Growth dynamics was investigated using X-ray diffraction, Rutherford backscattering spectrometry, and cross-sectional transmission electron microscopy. Upon annealing, Ge atoms migrate along the grain boundaries of polycrystalline Au and the epitaxial growth initiates at localized triple points between two Au grains and Si substrate, simultaneously incorporating a small amount of Si dissolved in Au. The Au is gradually displaced into the top Ge layer. Individual single crystal SixGei1-x islands then grow laterally as well as vertically. Finally, the islands coalesce to form a uniform layer of epitaxial SixGe1-x alloy on the Si substrate. The amount of Si incorporated in the final epitaxial film was found to be dependent upon the annealing temperature.

Epitaxial Growth of Near Noble Silicides on (111)Si by Rapid Thermal Annealing

1986 ◽  
Vol 74 ◽  
Author(s):  
H. C. Cheng ◽  
I. C. Wu ◽  
L. J. Chen
Keyword(s):  
Epitaxial Growth ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Furnace Annealing ◽  
Transmission Electron ◽  
Vacuum Method ◽  
Comparable Quality

AbstractThe epitaxial growth of near noble silicides, including CoSi2, NiSi2, FeSi2, Pd2 Si, and PtSi on (111)Si, by rapid thermal annealing was studied by transmission electron microscopy. Single-crystalline CoSi2 was formed on (111)Si in the solid phase epitaxy regime by a non-ultra-high vacuum method. The effect on gas ambient was found to be of critical importance on the growth of single-crystal CoSi2 on (111)Si. The best NiSi2, FeSi2, Pd2 Si, and PtSi epitaxy grown on (111)Si by rapid thermal annealing were found to be of comparable quality to those grown by conventional furnace annealing.

Shallow Junction Formation in As-Implanted Si by Low-Temperature Rapid Thermal Annealing

1989 ◽  
Vol 147 ◽  
Author(s):  
M. K. El-Ghor ◽  
S. J. Pennycook ◽  
R. A. Zuhr
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Dislocation Loops ◽  
Cross Sectional ◽  
Dopant Activation ◽  
Transmission Electron ◽  
Shallow Junctions ◽  
Surface Image ◽  
Long Time ◽  
Short Time

AbstractShallow junctions were formed in single-crystal Si(100) by implantation of As at energies between 2 and 17.5 keV followed by conventional furnace annealing or by rapid thermal annealing (RTA). Cross-sectional transmission electron microscopy (XTEM) showed that defect-free shallow junctions could be formed at temperatures as low as 700 °C by RTA, with about 60% dopant activation. From a comparison of short-time and long-time annealing, it is proposed that surface image forces are responsible for the efficient removal of end-of-range (EOR) dislocation loops

Influence of Rapid Thermal Annealing on Shallow BF2 Implantation into Pre-Amorphized Silicon

1983 ◽  
Vol 23 ◽  
Author(s):  
W. Maszara ◽  
C. Carter ◽  
D. K. Sadana ◽  
J. Liu ◽  
V. Ozguz ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Ion Beam ◽  
Liquid Nitrogen Temperature ◽  
Structural Defects ◽  
Structural Quality ◽  
Halogen Lamp ◽  
Cross Sectional ◽  
Plan View ◽  
Transmission Electron

ABSTRACTLow energy, shallow BF2+ implants were carried out at room or liquid nitrogen temperature into deep pre-amorphized (100) Si for better control of the dopant profile and post-annealing structural defects. Cross sectional and angle polished plan view transmission electron microscopy were used to study the structural quality of the implanted layer, while SIMS provided a chemical profile. Four types of structural defects were observed in BF2+ implanted, pre-amorphized samples following rapid thermal annealing with a halogen lamp. An in-situ ion beam annealing and the presence of F in the Si lattice were related to the creation of the defects. Good correlations between F gettering and TEM observed defects were found to exist. Implantation of B+ into a pre-amorphized Si surface and subsequent rapid thermal annealing was found to produce a wide defect-free surface layer.

Reaction Kinetics of Sputter-Deposited Ti On SiO2 Substrates during Rapid Thermal Annealing

1989 ◽  
Vol 146 ◽  
Author(s):  
E.J. Yun ◽  
H.G. Chun ◽  
K. Jung ◽  
D.L. Kwong ◽  
S. Lee
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Transmission Electron ◽  
Sputter Deposited ◽  
Kinetics Of

ABSTRACTIn this paper, the interactions of sputter-deposited Ti on SiO2 substrates during rapid thermal annealing in nitrogen at 550°C - 900°C for 10 - 60 s have been systematically studied using X-ray diffraction, Auger electron spectroscopy, transmission electron diffraction, TEM & cross-sectional TEM, and sheet resistance measurements.

Boron Diffusion in Fluorine Preamorphized Silicon During Rapid Thermal Annealing

1993 ◽  
Vol 303 ◽  
Author(s):  
H. Kinoshita ◽  
T. H. Huang ◽  
D. L. Kwong ◽  
P. E. Bakeman
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealed Sample ◽  
Transmission Electron Micrograph ◽  
Boron Diffusion ◽  
Cross Sectional ◽  
Dopant Activation ◽  
Enhanced Diffusion ◽  
Transmission Electron ◽  
Secondary Ion

ABSTRACTThe effect of fluorine preamorphization on boron diffusion and activation during rapid thermal annealing (RTA) has been investigated. Compared with low energy B or BF2 implant into crystalline Si, F preamorphization suppressed the transient enhanced diffusion of B and increased dopant activation. Results show that the tail diffusion was absent, and thus the junction depth of the RTA annealed sample was established by the as-implanted B profile. Secondary ion mass spectroscopy and cross-sectional transmission electron micrograph results show F accumulation near the surface and at end-of-range defects. The interaction of F with defects is believed to reduce the B diffusion during RTA.

Solid-Phase Epitaxial Regrowth and Dopant Activation of Arsenic. Implanted Metastable Pseudomorphic Ge0.08Si0.92 AND GeO.16SiO.84 ON Si(100)

1995 ◽  
Vol 379 ◽  
Author(s):  
D.Y.C. Lie ◽  
J.H. Song ◽  
M.-A. Nicolet ◽  
N.D. Theodore ◽  
J. Candelaria ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Room Temperature ◽  
Solid Phase ◽  
Strain Relaxation ◽  
Chemical Vapor ◽  
Layer By Layer ◽  
Solid Phase Epitaxy ◽  
Epitaxial Regrowth ◽  
Control Samples

ABSTRACTMetastable pseudomorphic GexSi1−x (x=8%,16%) films were deposited on p-Si(100) substrates by chemical-vapor-deposition and then implanted at room temperature with 90 keV arsenic ions to a dose of 1.5×1015/cm2. The implantation amorphizes approximately the top 125 nm of the 145 nm-thick GeSi layers. The Si-GeSi interfaces remain sharp after implantation. Implanted and non-implanted GeSi samples, together with implanted Si control samples, were subsequently annealed simultaneously by rapid thermal annealing in a nitrogen ambient at 600,700,800 × for 10,20,40s at each temperature. The implanted samples undergo layer-by-layer solid-phase epitaxial regrowth during annealing at or above 600 ×C. The amorphized and regrown GeSi layers are always fully relaxed with a very high density of dislocations (1010-1011/cm2). At a fixed annealing temperature, strain relaxation of an implanted GeSi film is substantially more extensive than that of a non-implanted one. About 50-90% of the implanted arsenic ions become electrically active after the completion of solid-phase epitaxy. The percentages of arsenic ions that are activated in the Si control samples are generally higher than those in GeSi. The room-temperature sheet electron mobility in GeSi is roughly 30% lower than that in Si for a given sheet electron concentration. We conclude that metastable GeSi on Si(100) amorphized by arsenic ions and recrystallized by solid-phase epitaxy cannot recover both its crystallinity and its pseudomorphic strain under rapid thermal annealing.

Solid Phase Epitaxial Regrowth of Implantation Amorphized Si0.7Ge0.3 Grown on (100) Silicon

1991 ◽  
Vol 235 ◽  
Author(s):  
C. Lee ◽  
K. S. Jones
Keyword(s):  
Defect Density ◽  
Solid Phase ◽  
Three Dimensional ◽  
Stacking Faults ◽  
Solid Phase Epitaxy ◽  
Cross Sectional ◽  
Strained Layers ◽  
Epitaxial Regrowth ◽  
Transmission Electron ◽  
Interfacial Strain

ABSTRACTThe solid phase epitaxial regrowth (SPER) process of implantation amorphized Si0.7Ge0.3 layers (850± Å thick) grown on (100) Si has been studied by cross-sectional transmission electron microscopy. For amorphous layers produced by 40 Ar+ implantation highly defective three dimensional regrowth was observed in both Si0.7Ge0.3 and Si. Stacking faults were the principle defect formed of both materials during regrowth. SPER after amorphization via 73 Ge+ implantation was also investigated. It was found that the SPER velocity of the 73 Ge+ implanted Si0.7 Ge0.7 Ge0.3 was about twice the velocity of the 40 Ar+ implanted samples; for 73 Ge+ implanted Si it was about three times that of the 40Ar+ implanted samples. The activation energy for SPER in 40Ar+ and in 73 Ge+ implanted Si0.7 Geo0.3 was about 1.6 and 2.6 eV, respectively. The defect density was significantly reduced in 73 Ge+ amorphized Si but not in the 73 Ge+ amorphized Si0.7 Ge0.3. It is proposed that limited Ar solubility inhibits high quality regrowth in both SiGe and Si. Upon 73 Ge+ amorphization and solid phase epitaxy the interfacial strain between the SiGe and Si cannot be accommodated. Thus the epitaxial process is poor in these SiGe strained layers regardless of the amorphizing species.

Sign in / Sign up

Export Citation Format

Share Document