Energies and Atomic Structures of Grain Boundaries in Silicon: Comparison Between Tilt and Twist Boundaries

1994 ◽  
Vol 343 ◽  
Author(s):  
M. Kohyama ◽  
R. Yamamoto ◽  
Y. Watanabe
Keyword(s):  
Tight Binding ◽  
The Other ◽  
Complex Structures ◽  
Structural Units ◽  
Atomic Structures ◽  
Interfacial Energies ◽  
Tilt Boundaries ◽  
The Stability ◽  
Twist Boundaries ◽  
The Ideal

ABSTRACTThe energies and atomic structures of tilt and twist boundaries in Si have been examined by using the tight-binding electronic theory, and the reason why twist boundaries are seldom found in polycrystalline Si has been investigated. About the frequently observed {122} Σ=9 and {255} Σ=27 tilt boundaries, the configurations without any coordination defects consistent with the electron microscopy observations have relatively small interfacial energies with small bond distortions. About the <111> Σ=7, <011> Σ=3 and <001> Σ = 5 twist boundaries, the configurations contain larger bond distortions or more coordination defects, and much larger interfacial energies than those of the tilt boundaries. The <001> twist boundaries have very complex structures as compared with the other twist boundaries, which can be explained by the morphology of the ideal surfaces. The stability of the tilt boundaries in Si can be explained by the viewpoint of the stable structural units consisting of atomic rings.

scholarly journals Separation of CO2 from Small Gas Molecules Using Deca-Dodecasil 3 Rhombohedral (DDR3) Membrane Synthesized via Ultrasonically Assisted Hydrothermal Growth Method

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Muhammad Mubashir ◽  
Yeong Yin Fong ◽  
Sidra Saqib ◽  
Ahmad Mukhtar ◽  
Sikander Rafiq ◽  
...  
Keyword(s):  
Gas Permeation ◽  
The Other ◽  
Gas Mixture ◽  
Growth Method ◽  
Gas Molecules ◽  
Separation Of Co2 ◽  
The Stability ◽  
Optimized Conditions ◽  
Molecular Sieving ◽  
The Ideal

Deca-dodecasil 3 rhombohedral (DDR3) membrane has received much attention in CO2 separation from small gas molecules because of its molecular sieving property and stable characteristics. Therefore, the present work is focusing on the utilization of previously fabricated membrane (synthesized in 3 days as reported in our previous work) to study the effect of hydrocarbons and its durability at the previously optimized conditions. Subsequently, gas permeation study was conducted on the DDR3 membrane in CO2 separation from small gas molecules and it was found that the permeance of H2, CO2, N2, and CH4 decreased in the order of H2 > CO2 > N2 > CH4, according to the increase in kinetic diameter of these gas molecules. Besides, it was observed that the ideal selectivities of the gas pairs decreased in the sequence of CO2/CH4 > CO2/N2 > H2/CO2. On the other hand, it was found that the presence of hydrocarbon impurities in the gas mixture containing CO2 and CH4 has directly affected the performance of DDR3 membrane and contributed to the losses of CO2 permeability, CH4 permeability, and CO2/CH4 selectivity of 39.1%, 14.8%, and 4.2%, respectively. Consequently, from the stability test, the performance of DDR3 membrane remained stable for 96 h, even after the separation testing using CO2 and CH4 gas mixture containing hydrocarbon impurities.

Theoretical analysis of tilt grain boundaries in GaN at the atomic scale

2002 ◽  
Vol 743 ◽  
Author(s):  
Jun Chen ◽  
Pierre Ruterana ◽  
Gérard Nouet
Keyword(s):  
Grain Boundaries ◽  
Rotation Angle ◽  
The Other ◽  
Atomic Scale ◽  
Threading Dislocations ◽  
High Angle ◽  
Structural Units ◽  
Atomic Structures ◽  
Very High ◽  
Weber Potential

ABSTRACTEpitaxial layers of GaN contain a very high density of threading dislocations. In the first stage of growth they may form low and high angle grain boundaries. Energetic calculations of <0001> tilt grain boundaries have been performed with the Stillinger-Weber potential modified to take into account the wrong bonds Ga-Ga and N-N. The variation of the energy has been calculated as a function of the rotation angle. Two minima exist with special atomic structures based on a limited number of structural units. They are used to describe the other misorientations in terms of dislocation cores.

Origins of the Gap States in Polycrystalline Silicon: Tight-Binding Calculations of Twist Boundaries

1992 ◽  
Vol 262 ◽  
Author(s):  
M. Kohyama ◽  
S. Kose ◽  
R. Yamamoto
Keyword(s):  
Electronic Structures ◽  
Polycrystalline Silicon ◽  
Tight Binding ◽  
Electronic States ◽  
Structural Disorder ◽  
Interfacial Energies ◽  
Amorphous Si ◽  
Gap States ◽  
Twist Boundaries ◽  
Generate Characteristic

ABSTRACTThe atomic and electronic structures of the twist boundaries Σ (=3 (011), Σ=7 (111) and Σ=5 (001)) in Si have been calculated by using the transferable SETB method coupled with the supercell technique. The twist boundaries in Si contain larger structural disorder or more defects and larger interfacial energies than tilt grain boundaries. Several kinds of structural disorder or defects have been found to generate characteristic electronic states inside the gap. The present structural disorder or defects and the gap states are the candidates of the origins of the observed band-tails or mid-gap states in polycrystalline Si as well as those In amorphous Si.

Uniformity of Magnification from Different Electron Microscopes

1967 ◽  
Vol 25 ◽  
pp. 32-33
Author(s):  
Godfrey C. Hoskins ◽  
V. Williams ◽  
V. Allison
Keyword(s):  
Diffraction Grating ◽  
The Other ◽  
Carbon Replica ◽  
Electron Microscopes ◽  
The Stability

The method demonstrated is an adaptation of a proven procedure for accurately determining the magnification of light photomicrographs. Because of the stability of modern electrical lenses, the method is shown to be directly applicable for providing precise reproducibility of magnification in various models of electron microscopes.A readily recognizable area of a carbon replica of a crossed-line diffraction grating is used as a standard. The same area of the standard was photographed in Phillips EM 200, Hitachi HU-11B2, and RCA EMU 3F electron microscopes at taps representative of the range of magnification of each. Negatives from one microscope were selected as guides and printed at convenient magnifications; then negatives from each of the other microscopes were projected to register with these prints. By deferring measurement to the print rather than comparing negatives, correspondence of magnification of the specimen in the three microscopes could be brought to within 2%.

TEM Study of a Tilt Boundary in Hot-Pressed Silicon

1981 ◽  
Vol 39 ◽  
pp. 160-161
Author(s):  
C. B. Carter ◽  
J. Rose ◽  
D. G. Ast
Keyword(s):  
Electron Diffraction ◽  
Imaging Technique ◽  
Interface Structure ◽  
Large Area ◽  
Weak Beam ◽  
Lattice Fringe ◽  
Electron Diffraction Technique ◽  
Tilt Boundaries ◽  
Beam Technique ◽  
Twist Boundaries

The hot-pressing technique which has been successfully used to manufacture twist boundaries in silicon has now been used to form tilt boundaries in this material. In the present study, weak-beam imaging, lattice-fringe imaging and electron diffraction techniques have been combined to identify different features of the interface structure. The weak-beam technique gives an overall picture of the geometry of the boundary and in particular allows steps in the plane of the boundary which are normal to the dislocation lines to be identified. It also allows pockets of amorphous SiO2 remaining in the interface to be recognized. The lattice-fringe imaging technique allows the boundary plane parallel to the dislocation to be identified. Finally the electron diffraction technique allows the periodic structure of the boundary to be evaluated over a large area - this is particularly valuable when the dislocations are closely spaced - and can also provide information on the structural width of the interface.

High-resolution x-ray analysis of dislocation networks nn tilt boundaries

1988 ◽  
Vol 46 ◽  
pp. 612-613
Author(s):  
J. R. Michael ◽  
C. H. Lin ◽  
S. L. Sass
Keyword(s):  
Grain Boundaries ◽  
Analytical Electron Microscopy ◽  
Solute Segregation ◽  
X Ray ◽  
Periodic Arrays ◽  
Analytical Electron ◽  
Primary Dislocation ◽  
Tilt Boundaries ◽  
Polycrystalline Solids ◽  
Twist Boundaries

The segregation of solute atoms to grain boundaries in polycrystalline solids can be responsible for embrittlement of the grain boundaries. Although Auger electron spectroscopy (AES) and analytical electron microscopy (AEM) have verified the occurrence of solute segregation to grain boundaries, there has been little experimental evidence concerning the distribution of the solute within the plane of the interface. Sickafus and Sass showed that Au segregation causes a change in the primary dislocation structure of small angle [001] twist boundaries in Fe. The bicrystal specimens used in their work, which contain periodic arrays of dislocations to which Au is segregated, provide an excellent opportunity to study the distribution of Au within the boundary by AEM.The thin film Fe-0.8 at% Au bicrystals (composition determined by Rutherford backscattering spectroscopy), ∼60 nm thick, containing [001] twist boundaries were prepared as described previously. The bicrystals were analyzed in a Vacuum Generators HB-501 AEM with a field emission electron source and a Link Analytical windowless x-ray detector.

High-resolution microscopy of twin boundaries in gold

1987 ◽  
Vol 45 ◽  
pp. 260-261
Author(s):  
William Krakow ◽  
David A. Smith
Keyword(s):  
High Resolution ◽  
Specimen Preparation ◽  
Gold Films ◽  
Boundary Area ◽  
Transmission Electron ◽  
Recent Developments ◽  
Tilt Boundaries ◽  
High Resolution Microscopy ◽  
Twist Boundaries

Recent developments in specimen preparation, imaging and image analysis together permit the experimental determination of the atomic structure of certain, simple grain boundaries in metals such as gold. Single crystal, ∼125Å thick, (110) oriented gold films are vapor deposited onto ∼3000Å of epitaxial silver on (110) oriented cut and polished rock salt substrates. Bicrystal gold films are then made by first removing the silver coated substrate and placing in contact two suitably misoriented pieces of the gold film on a gold grid. Controlled heating in a hot stage first produces twist boundaries which then migrate, so reducing the grain boundary area, to give mixed boundaries and finally tilt boundaries perpendicular to the foil. These specimens are well suited to investigation by high resolution transmission electron microscopy.

NEUROTIC SYMPTOMATICS RELATED TO PERSONAL CHARACTERISTICS IN YOUTH

2019 ◽  
pp. 2014-2019
Author(s):  
Milen Dimov
Keyword(s):  
Personal Characteristics ◽  
The Self ◽  
The Other ◽  
Social Responsiveness ◽  
Training Process ◽  
Self Assessment ◽  
School Year ◽  
Real Behavior ◽  
Low Levels ◽  
The Ideal

The present study traces the dynamics of personal characteristics in youth and the manifested neurotic symptoms in the training process. These facts are the reason for the low levels of school results in the context of the existing theoretical statements of the problem and the empirical research conducted among the trained teenagers. We suggest that the indicators of neurotic symptomatology in youth – aggression, anxiety, and neuroticism, are the most demonstrated, compared to the other studied indicators of neurotic symptomatology. Studies have proved that there is a difference in the act of neurotic symptoms when tested in different situations, both in terms of expression and content. At the beginning of the school year, neurotic symptoms, more demonstrated in some aspects of aggressiveness, while at the end of school year, psychotism is more demonstrated. The presented summarized results indicate that at the beginning of the school year, neurotic symptoms are strongly associated with aggression. There is a tendency towards a lower level of social responsiveness, both in the self-assessment of real behavior and in the ideal “I”-image of students in the last year of their studies. The neurotic symptomatology, more demonstrated due to specific conditions in the life of young people and in relation to the characteristics of age.

KONSTRUKSI ISLAM DALAM KEKUASAAN NEGARA

1970 ◽  
Vol 6 (2) ◽  
Author(s):  
Nurul Aini Musyarofah
Keyword(s):  
Islamic Law ◽  
Social Condition ◽  
The Other ◽  
Good Society ◽  
Ideal Form ◽  
Other Hand ◽  
Islamic Politics ◽  
The Relationship ◽  
The Ideal

The relationship between Islam and state raises a controversy that includes two main groups;formalists and substantialists. Both of them intend to achieve a good social condition which is inaccordance with Islamic politics. The ideal form of good society to be achieved is principallydescribed in the main source of Islamic law, Al Qur’an and As Sunnah, as follows. A form of goodsociety should supprot equality and justice, egalitarianism, and democracy in its social community.The next problem is what the needed methods and instruments to achieve the ideal Islamic politicsare. In this case, the debate on the formalization and substance of Islamic teaching is related to therunning formal political institution.Each group claims itself to be the most representative to the ideal Islam that often leads to anescalating conflict. On the other hand thr arguments of both groups does not reach the wholeMuslims. As a result, the discourse of Islam and state seems to be elitist and political. As a result,Both groups suspect each other each other and try to utilize the controversy on the relationshipbetween Islam and state to get their own benefit which has no relation with the actualization ofIslamic teaching.

scholarly journals Black Hole Algorithm for Sustainable Design of Counterfort Retaining Walls

2020 ◽  
Vol 12 (7) ◽  
pp. 2767 ◽  
Author(s):  
Víctor Yepes ◽  
José V. Martí ◽  
José García
Keyword(s):  
Black Hole ◽  
Sustainable Design ◽  
Retaining Walls ◽  
The Other ◽  
Trade Off ◽  
Construction Company ◽  
Geometric Variables ◽  
The Stability ◽  
The Cost ◽  
Black Hole Algorithm

The optimization of the cost and CO 2 emissions in earth-retaining walls is of relevance, since these structures are often used in civil engineering. The optimization of costs is essential for the competitiveness of the construction company, and the optimization of emissions is relevant in the environmental impact of construction. To address the optimization, black hole metaheuristics were used, along with a discretization mechanism based on min–max normalization. The stability of the algorithm was evaluated with respect to the solutions obtained; the steel and concrete values obtained in both optimizations were analyzed. Additionally, the geometric variables of the structure were compared. Finally, the results obtained were compared with another algorithm that solved the problem. The results show that there is a trade-off between the use of steel and concrete. The solutions that minimize CO 2 emissions prefer the use of concrete instead of those that optimize the cost. On the other hand, when comparing the geometric variables, it is seen that most remain similar in both optimizations except for the distance between buttresses. When comparing with another algorithm, the results show a good performance in optimization using the black hole algorithm.

Sign in / Sign up

Export Citation Format

Share Document