The Staebler-Wronski Effect and the Thermal Equilibration of Defect and Carrier Concentrations

1994 ◽  
Vol 336 ◽  
Author(s):  
R.M.A. Dawson ◽  
C.M. Fortmann ◽  
Y.M. Li ◽  
C.R. Wronski
Keyword(s):  
High Temperature ◽  
Fermi Level ◽  
Temperature Dependence ◽  
Amorphous Silicon ◽  
Elevated Temperatures ◽  
Free Carrier ◽  
Annealed State ◽  
Thermal Equilibration ◽  
Staebler Wronski Effect ◽  
Substrate Temperatures

ABSTRACTLight induced degradation of intrinsic Amorphous silicon (a-Si:H) is investigated as a function of temperature. Previous work described an equilibrium framework for the high temperature behavior of dangling bonds defects (DB) 11]; and the temperature dependence of the annealed state photo, σPH, and dark, σD, conductivities of a series of intrinsic a-Si:H Materials deposited over a range of substrate temperatures, 200°C < Ts < 380°C [2]. These results are extended to the light degraded state where elevated temperatures provide for equilibration of the free carrier and DB concentrations. For the equilibrium, light degraded state, both σD and σPH, decrease compared to the annealed state while the ratio, σD/σPH remains unchanged. Relationships between the ratio [DB+]/[DB] and the Fermi level are derived from the equilibrium framework.

scholarly journals Temperature Dependence of Mechanical, Electrical Properties and Crystal Structure of Polyethylene Blends for Cable Insulation

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1922 ◽  
Author(s):  
Lunzhi Li ◽  
Lisheng Zhong ◽  
Kai Zhang ◽  
Jinghui Gao ◽  
Man Xu
Keyword(s):  
High Temperature ◽  
Electrical Properties ◽  
Temperature Dependence ◽  
Elevated Temperatures ◽  
Breakdown Strength ◽  
Temperature Stability ◽  
Xrd Analysis ◽  
Insulation Material ◽  
Cable Insulation ◽  
Polyethylene Blends

There is a long-standing puzzle concerning whether polyethylene blends are a suitable substitution for cable-insulation-used crosslinking polyethylene (XLPE) especially at elevated temperatures. In this paper, we investigate temperature dependence of mechanical, electrical properties of blends with 70 wt % linear low density polyethylene (LLDPE) and 30 wt % high density polyethylene (HDPE) (abbreviated as 70 L-30 H). Our results show that the dielectric loss of 70 L-30 H is about an order of magnitude lower than XLPE, and the AC breakdown strength is 22% higher than XLPE at 90 °C. Moreover, the dynamic mechanical thermal analysis (DMA) measurement and hot set tests suggest that the blends shows optimal mechanical properties especially at high temperature with considerable temperature stability. Further scanning electron microscope (SEM) observation and X-ray diffraction (XRD) analysis uncover the reason for the excellent high temperature performance and temperature stability, which can be ascribed to the uniform fine-spherulite structure in 70 L-30 H blends with high crystallinity sustaining at high temperature. Therefore, our findings may enable the potential application of the blends as cable insulation material with higher thermal-endurance ability.

Photo-induced changes in the coefficient of the temperature dependence of the Fermi level in discharge-produced amorphous silicon

1982 ◽  
Vol 43 (9) ◽  
pp. 1419-1424 ◽  
Author(s):  
J. Bullot ◽  
M. Galin ◽  
M. Gauthier ◽  
B. Bourdon ◽  
Y. Catherine
Keyword(s):  
Fermi Level ◽  
Temperature Dependence ◽  
Amorphous Silicon ◽  
Induced Changes

scholarly journals High-temperature dependence of low magnetization Mn5Ge3 phase formation of sputtered thin films

2017 ◽  
Vol 30 (4) ◽  
pp. 61-64
Author(s):  
Adriana Alvídrez-Lechuga ◽  
José T Holguín-Momaca ◽  
Carlos Roberto Santillán-Rodríguez ◽  
José Andrés Matutes-Aquino ◽  
Sion Federico Olive-Méndez
Keyword(s):  
Thin Films ◽  
High Temperature ◽  
Temperature Dependence ◽  
Phase Formation ◽  
Magnetic Thin Films ◽  
Spin Transfer Torque ◽  
Spin Transfer ◽  
Carbon Doping ◽  
Low Energy Consumption ◽  
Substrate Temperatures

We report on the high-temperature dependence of the Mn5Ge3 phase formation on Ge(001). High substrate temperatures from 650 to 850 °C lead to the formation of the Mn5Ge3 thin films with a low magnetization of ~250 kAm-1, which is an important characteristic for faster and low energy consumption of the switching of the magnetic orientation of magnetic thin films by spin-transfer torque. The highest temperature conducts to the formation of the Mn5Ge3 phase with only a small amount of Mn5Ge2 hexagonal clusters. Additionally, carbon doping of the Mn5Ge3 sample grown at 750 °C exhibits an enhancement of the Curie temperature from 296 K to 390 K. The growth mechanism corresponds to a Volmer-Weber mode.

High-Temperature Instability of A Cr2Nb-Nb(Cr) Microlaminate Composite

1996 ◽  
Vol 54 ◽  
pp. 374-375
Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Aircraft Engine ◽  
Lattice Parameter ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Cross Sectional ◽  
Bcc Structure

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.

Phase transformation and layer evolution in molybdenum disilicide-silicon carbide nanolayered coatings

1994 ◽  
Vol 52 ◽  
pp. 538-539
Author(s):  
H. Kung ◽  
T. R. Jervis ◽  
J.-P. Hirvonen ◽  
M. Nastasi ◽  
T. E. Mitchell ◽  
...  
Keyword(s):  
Phase Transformation ◽  
High Temperature ◽  
Oxidation Resistance ◽  
Elevated Temperatures ◽  
Matrix Material ◽  
Molybdenum Disilicide ◽  
High Temperature Strength ◽  
Cross Sectional ◽  
Good Oxidation Resistance ◽  
Structural Applications

MoSi2 is a potential matrix material for high temperature structural composites due to its high melting temperature and good oxidation resistance at elevated temperatures. The two major drawbacksfor structural applications are inadequate high temperature strength and poor low temperature ductility. The search for appropriate composite additions has been the focus of extensive investigations in recent years. The addition of SiC in a nanolayered configuration was shown to exhibit superior oxidation resistance and significant hardness increase through annealing at 500°C. One potential application of MoSi2- SiC multilayers is for high temperature coatings, where structural stability ofthe layering is of major concern. In this study, we have systematically investigated both the evolution of phases and the stability of layers by varying the heat treating conditions.Alternating layers of MoSi2 and SiC were synthesized by DC-magnetron and rf-diode sputtering respectively. Cross-sectional transmission electron microscopy (XTEM) was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: crystallization and phase transformation of MoSi2, crystallization of SiC, and spheroidization of the layer structures.

ABOUT HEAT CAPACITY OF TITANIUM CARBIDE TiCx

2019 ◽  
pp. 56-66
Author(s):  
I. Khidirov ◽  
V. V. Getmanskiy ◽  
A. S. Parpiev ◽  
Sh. A. Makhmudov
Keyword(s):  
Heat Capacity ◽  
High Temperature ◽  
Titanium Carbide ◽  
Temperature Dependence ◽  
Carbon Concentration ◽  
Room Temperature ◽  
Thermodynamic Characteristics ◽  
Liquid Nitrogen Temperature ◽  
Analysis Data ◽  
Thermal Excitation

This work relates to the field of thermophysical parameters of refractory interstitial alloys. The isochoric heat capacity of cubic titanium carbide TiCx has been calculated within the Debye approximation in the carbon concentration  range x = 0.70–0.97 at room temperature (300 K) and at liquid nitrogen temperature (80 K) through the Debye temperature established on the basis of neutron diffraction analysis data. It has been found out that at room temperature with decrease of carbon concentration the heat capacity significantly increases from 29.40 J/mol·K to 34.20 J/mol·K, and at T = 80 K – from 3.08 J/mol·K to 8.20 J/mol·K. The work analyzes the literature data and gives the results of the evaluation of the high-temperature dependence of the heat capacity СV of the cubic titanium carbide TiC0.97 based on the data of neutron structural analysis. It has been proposed to amend in the Neumann–Kopp formula to describe the high-temperature dependence of the titanium carbide heat capacity. After the amendment, the Neumann–Kopp formula describes the results of well-known experiments on the high-temperature dependence of the heat capacity of the titanium carbide TiCx. The proposed formula takes into account the degree of thermal excitation (a quantized number) that increases in steps with increasing temperature.The results allow us to predict the thermodynamic characteristics of titanium carbide in the temperature range of 300–3000 K and can be useful for materials scientists.

WIELAND-K88

Alloy Digest ◽  
2005 ◽  
Vol 54 (12) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Stress Relaxation ◽  
Copper Alloy ◽  
Elevated Temperatures ◽  
Heat Treating ◽  
Relaxation Resistance ◽  
Temperature Performance ◽  
Very High

Abstract Wieland K-88 is a copper alloy with very high electrical and thermal conductivity, good strength, and excellent stress relaxation resistance at elevated temperatures. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CU-738. Producer or source: Wieland Metals Inc.

DOWMETAL HZ32XA

Alloy Digest ◽  
1956 ◽  
Vol 5 (7) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Creep Resistance ◽  
Zirconium Alloy ◽  
Elevated Temperatures ◽  
Heat Treating ◽  
High Temperature Creep ◽  
Aged Condition ◽  
Chemical Company ◽  
Temperature Performance

Abstract DOWMETAL HZ32XA is a magnesium-thorium-zinc-zirconium alloy having good high temperature creep resistance, and is recommended for applications at elevated temperatures. It is used in the artificially aged condition (T5). This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance as well as heat treating, machining, and joining. Filing Code: Mg-26. Producer or source: The Dow Chemical Company.

UDIMET 105

Alloy Digest ◽  
1972 ◽  
Vol 21 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Surface Treatment ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
Heat Treating ◽  
Nickel Base Alloy ◽  
Temperature Performance ◽  
Nickel Base

Abstract UDIMET 105 is a nickel-base alloy which was developed for service at elevated temperatures. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-175. Producer or source: Special Metals Corporation.

Sign in / Sign up

Export Citation Format

Share Document