Structure and Magnetic Properties of FE/ZR Multilayer Films

1993 ◽  
Vol 313 ◽  
Author(s):  
Toyohiko J. Konno ◽  
Takenori Nakayama ◽  
Bruce M. Clemens ◽  
Robert Sinclair
Keyword(s):  
Magnetic Properties ◽  
Amorphous Layer ◽  
Multilayer Films ◽  
Amorphous Structure ◽  
Asymptotic Model ◽  
Vibrating Sample Magnetometry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
The One

ABSTRACTWe investigated structural and magnetic properties of Fe/Zr Multilayer films using high-resolution transmission electron Microscopy, X-ray diffraction and vibrating sample Magnetometry. For films with wavelength (Λ) ≥ 80Å, the interface region between the Fe and Zr layers exhibits a 15–20Å thick amorphous structure. The Magnetization curves of these films showed a monotonous decrease in the saturation magnetizations with Λ, whose trend is well explained by a simple asymptotic model that assumes the interface amorphous layer to be non-ferromagnetic. Films with Λ≤40Å exhibit a compositionally-Modulated amorphous structure. The latter films are paramagnetic except for the one with Λ=40Å, which showed a superparamagnetic behavior.

scholarly journals A Study of Thin Film Resistors Prepared Using Ni-Cr-Si-Al-Ta High Entropy Alloy

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Ruei-Cheng Lin ◽  
Tai-Kuang Lee ◽  
Der-Ho Wu ◽  
Ying-Chieh Lee
Keyword(s):  
Annealing Temperature ◽  
Phase Evolution ◽  
Amorphous Structure ◽  
High Entropy Alloy ◽  
X Ray Diffraction ◽  
Temperature Coefficient Of Resistance ◽  
X Ray ◽  
High Entropy ◽  
Transmission Electron ◽  
Thin Film Resistors

Ni-Cr-Si-Al-Ta resistive thin films were prepared on glass and Al2O3substrates by DC magnetron cosputtering from targets of Ni0.35-Cr0.25-Si0.2-Al0.2casting alloy and Ta metal. Electrical properties and microstructures of Ni-Cr-Si-Al-Ta films under different sputtering powers and annealing temperatures were investigated. The phase evolution, microstructure, and composition of Ni-Cr-Si-Al-Ta films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Auger electron spectroscopy (AES). When the annealing temperature was set to 300°C, the Ni-Cr-Si-Al-Ta films with an amorphous structure were observed. When the annealing temperature was at 500°C, the Ni-Cr-Si-Al-Ta films crystallized into Al0.9Ni4.22, Cr2Ta, and Ta5Si3phases. The Ni-Cr-Si-Al-Ta films deposited at 100 W and annealed at 300°C which exhibited the higher resistivity 2215 μΩ-cm with −10 ppm/°C of temperature coefficient of resistance (TCR).

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Influence of Alloying Additions on Enhancement of Soft Magnetic Properties Effect and Crystallization in FeXSiB (X=Cu, V, Co, Zr, Nb) Amorphous Alloys

2007 ◽  
Vol 130 ◽  
pp. 171-174 ◽  
Author(s):  
Z. Stokłosa ◽  
G. Badura ◽  
P. Kwapuliński ◽  
Józef Rasek ◽  
G. Haneczok ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Crystallization Process ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
X Ray ◽  
Second Stage ◽  
Transmission Electron

The crystallization and optimization of magnetic properties effects in FeXSiB (X=Cu, V, Co, Zr, Nb) amorphous alloys were studied by applying X-ray diffraction methods, high resolution transmission electron microscopy (HRTEM), resistometric and magnetic measurements. The temperatures of the first and the second stage of crystallization, the 1h optimization annealing temperature and the Curie temperature were determined for different amorphous alloys. Activation energies of crystallization process were obtained by applying the Kissinger method. The influence of alloy additions on optimization effect and crystallization processes was carefully examined.

Influence of Gd Addition on the Structure and Capability of Ni-Mn-In Metamagnetic Shape Memory Alloys

2012 ◽  
Vol 535-537 ◽  
pp. 950-953
Author(s):  
Li Na Bai ◽  
Gui Xing Zheng ◽  
Zhi Jian Duan ◽  
Jian Jun Zhang
Keyword(s):  
Differential Scanning Calorimetry ◽  
Magnetic Properties ◽  
Magnetic Property ◽  
Transition Temperature ◽  
Martensitic Transformation ◽  
Room Temperature ◽  
Vibrating Sample Magnetometry ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

The influences of Gd concentration on martensitic transformation and magnetic properties of NiMnIn alloys were investigated by differential scanning calorimetry (DSC) , vibrating sample magnetometry (VSM), X-ray diffraction (XRD) and etc. It is Observed through the experiment: the addition of Gd enhances martensite transition temperature;X-ray diffraction analysis of experimental alloys is revealed that to the mixture is martensite and austenite at room temperature; content of Gd is not proportional to the improvement of magnetic property.

New method for the production of bulk amorphous materials of Nd–Fe–B alloys

2005 ◽  
Vol 20 (3) ◽  
pp. 563-566 ◽  
Author(s):  
Tetsuji Saito ◽  
Hiroyuku Takeishi ◽  
Noboru Nakayama
Keyword(s):  
Electron Microscopy ◽  
Amorphous Materials ◽  
Room Temperature ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons

We report a new compression shearing method for the production of bulk amorphous materials. In this study, amorphous Nd–Fe–B melt-spun ribbons were successfully consolidated into bulk form at room temperature by the compression shearing method. X-ray diffraction and transmission electron microscopy studies revealed that the amorphous structure was well maintained in the bulk materials. The resultant bulk materials exhibited the same magnetic properties as the original amorphous Nd–Fe–B materials.

Nickel Ferrite: Combustion Synthesis, Characterization and Magnetic Properties

2005 ◽  
Vol 498-499 ◽  
pp. 618-623 ◽  
Author(s):  
Ana Cristina Figueiredo de Melo Costa ◽  
Lucianna Gama ◽  
M.R. Morelli ◽  
Ruth Herta Goldsmith Aliaga Kiminami
Keyword(s):  
Magnetic Properties ◽  
Nickel Ferrite ◽  
High Speed ◽  
High Specific Surface Area ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
X Ray ◽  
Railway Systems ◽  
Transmission Electron ◽  
Dry Pressing

Nanosized spinel nickel ferrite particles have attracted considerable attention and efforts continue to investigate them for their technological importance to the microwave industries, high speed digital tap or disk recording, repulsive suspension for use in levitated railway systems, ferrofluids, catalysis and magnetic refrigeration systems. Nanosize nickel ferrite powders (NiFe2O4) have been prepared by combustion reaction using nitrates and urea as fuel. The resulting powders were characterized by X-ray diffraction (XRD), BET, and transmission electron microscopy (TEM). The results showed nanosize nickel ferrite powders with high specific surface area (55.21 m2/g). The powders showed extensive XRD line broadening and the crystallite size calculated from the XRD line broadening was 18.0 nm. The samples were uniaxially compacted by dry pressing, sintered at 1200°C/2h and characterized by bulk density, SEM and magnetic properties measurements. The samples showed uniform microstructures with grain size of 4.45 μm, maximum flux density of 0.18T, field coercive of the 488 A/m, and hysteresis loss of 47.58 W/kg.

Sonochemical Co-Precipitation Synthesis of Gallic Acid-Modified Magnetite

2015 ◽  
Vol 1101 ◽  
pp. 286-289 ◽  
Author(s):  
Maya Rahmayanti ◽  
Sri Juari Santosa ◽  
Sutarno
Keyword(s):  
Magnetic Properties ◽  
Gallic Acid ◽  
Precipitation Method ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
One Step ◽  
The Fourier Transform ◽  
The One ◽  
Co Precipitation

Gallic acid-modified magnetites were synthesized by one and two-step reactions via the newly developed sonochemical co-precipitation method. The two-step reaction included the formation of magnetite powder and mixing the magnetite powder with gallic acid solution, while the one-step reaction did not go through the formation magnetite powder. The obtained gallic acid-modified magnetites were characterized by the Fourier Transform Infrared (FTIR) spectroscopy, the X-Ray Diffraction (XRD) and the Scanning Electron Microscopy (SEM). More over, the magnetic properties were studied by using a Vibrating Sample Magnetometer (VSM). The characterization results showed that there were differences in crystalinity, surface morphology and magnetic properties of products that were formed by one and two-step reactions.

ZnFe2O4 Modified by Fe(NO3)3 for the Synthesis of Ionic Ferrofluids

2010 ◽  
Vol 177 ◽  
pp. 32-36 ◽  
Author(s):  
An Rong Wang ◽  
Jian Li ◽  
Qing Mei Zhang ◽  
Hua Miao
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Photoelectron Spectroscopy ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Znfe2o4 Nanoparticles

Weak magnetic ZnFe2O4 nanoparticles were prepared by coprecipitation and treated with different concentrations of Fe(NO3)3 solution. Untreated and treated particles were studied using a vibrating sample magnetometer, transmission electron microscope, by X-ray diffraction, X-ray energy dispersive spectroscopy and X photoelectron spectroscopy. The results showed that, after treatment, the ZnFe2O4/γ-Fe2O3 forms disphase nanoparticles, with enlarged size, enhanced magnetic properties and with a surface parceled with Fe(NO3)3. The size of the particles and their magnetic properties are related to the concentration of the treatment solution. The particle size and magnetic properties could be controlled by controlling the concentration of treating solution, therefore nanoparticles can be more widely used.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

EFFECT OF NANOCRYSTALLIZATION ANNEALING ON MAGNETIC PROPERTIES AND MAGNETOIMPEDANCE OF CO-BASE RIBBONS

2012 ◽  
Vol 05 ◽  
pp. 841-846
Author(s):  
AMIR KEYVANARA ◽  
REZA GHOLAMIPOUR ◽  
SHAMSEDIN MIRDAMADI ◽  
FARZAD SHAHRI ◽  
HOSSEIN SEPEHRI AMIN
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Magnetic Properties ◽  
Structural Studies ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons ◽  
Nanocrystalline Phases

Melt spun ribbons of Co 64 Fe 4 Ni 2 B 19 Si 8 Cr 3 alloy have been prepared and the nanocrystallization process was carried out by the heat treatment of the as spun ribbons above the crystallization temperature. Structural studies of the samples have been performed by transmission electron microscopy and X-ray diffraction. Magnetic properties of the samples and magnetoimpedance measurements were investigated and it was revealed that magnetic properties and magnetoimpedance of the samples deteriorate by the formation of nanocrystalline phases.

Sign in / Sign up

Export Citation Format

Share Document