Preparation of Cross-Sectional TEM Samples of PbTe and CdxPb1−x Te on BaF2

1990 ◽  
Vol 199 ◽  
Author(s):  
John P. McCaffrey ◽  
Suhit R. Das ◽  
John G. Cook
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
Sample Preparation ◽  
Argon Atom ◽  
Low Energy ◽  
Atom Beam ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Preparation Techniques

ABSTRACTEpitaxial PbTe and CdxPb1−xTe films have been grown on single crystal (111) BaF2 by low energy bias sputtering, and have been analyzed by transmission electron microscopy (TEM) and transmission electron diffraction (TED). Preparation of suitable cross-sectional TEM samples was made difficult by the tendency of the substrate to cleave apart during dimpling, and by the epoxy forming bridges across the sample during atom milling. Suitable preparation techniques were developed employing back-polishing the BaF2 substrates to <0.2 mm thickness, using a suitable epoxy, and shielding the argon atom beam during milling to prevent milling parallel to the surface. In cases where an epoxy bridge did form across the sample, the bridge was broken manually or by atom milling, depending upon the area of sample which was being investigated. These techniques are applicable to other materials which produce similar problems during TEM sample preparation.

The Challenge and Methods of TEM Cross-Sectioning of < 0.25 Micron Plugs

1998 ◽  
Vol 523 ◽  
Author(s):  
C. Amy Hunt ◽  
Yuhong Zhang ◽  
David Su
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Failure Analysis ◽  
Cross Section ◽  
Adhesion Layer ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Sectional Plane ◽  
Preparation Techniques

AbstractTransmission electron microscopy (TEM) is a useful tool in process evaluation and failure analysis for semiconductor industries. A common focus of semiconductor TEM analyses is metalization vias (plugs) and it is often desirable to cross-section through a particular one. If the cross-sectional plane deviates away from the center of the plug, then the thin adhesion layer around the plug will be blurred by surrounding materials such as the inter-layer dielectric and the plug material. The importance of these constraints, along with the difficulty of precision sample preparation, has risen sharply as feature sizes have fallen to 0.25 μm and below. The suitability of common sample preparation techniques for these samples is evaluated.

Tem, Raman, and Langmuir Probe Studies of the Heteroepitaxial Growth of Metastable Cd(x)pb (1–X) Te Alloys Deposited on BaF2 by Low-Energy Bias Sputtering

1990 ◽  
Vol 201 ◽  
Author(s):  
Suhit R. Das ◽  
John G. Cook ◽  
David J. Lockwood
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
Epitaxial Growth ◽  
Langmuir Probe ◽  
Low Energy ◽  
Heteroepitaxial Growth ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Magnetron Sputter

AbstractMetastable Cd(x)Pb(1–x)Te films with x values from 0 to 0.47, well past the range of bulk thermodynamic solubility, have been grown on single crystal (lll) BaF2 by co-deposition from CdTe and PbTe r.f. magnetron sputter targets. Cross-sectional transmission electron microscopy and transmission electron diffraction revealed epitaxial growth across the interface. However, the lattice of the deposited epilayers was observed to be typically rotated 180°C about the surface normal <111> axis of the substrate. Raman spectra of the alloys showed no evidence of segregation. Langmuir probe diagnostics were employed to estimate the energy of the ions incident on the substrate during growth which promote extended miscibility in the alloy epilayers.

TEM Sample Preparation Tricks for Advanced DRAMs

2015 ◽  
Author(s):  
Ching Shan Sung ◽  
Hsiu Ting Lee ◽  
Jian Shing Luo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Characterization Of Materials

Abstract Transmission electron microscopy (TEM) plays an important role in the structural analysis and characterization of materials for process evaluation and failure analysis in the integrated circuit (IC) industry as device shrinkage continues. It is well known that a high quality TEM sample is one of the keys which enables to facilitate successful TEM analysis. This paper demonstrates a few examples to show the tricks on positioning, protection deposition, sample dicing, and focused ion beam milling of the TEM sample preparation for advanced DRAMs. The micro-structures of the devices and samples architectures were observed by using cross sectional transmission electron microscopy, scanning electron microscopy, and optical microscopy. Following these tricks can help readers to prepare TEM samples with higher quality and efficiency.

Growth and Structure of Al/MgO Interfaces

1994 ◽  
Vol 357 ◽  
Author(s):  
T. Wagner ◽  
M. Ruhle
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Ultra High Vacuum ◽  
Structural Defects ◽  
Cross Sectional ◽  
Aluminum Films ◽  
Transmission Electron

AbstractThe A1/MgO system has been used as a model system to study growth processes and structure at metal/ceramic interfaces. Aluminum films were grown on air-cleaved MgO (100) substrates in ultra high vacuum (UHV) by molecular beam epitaxy (MBE). The substrates and films were characterized by reflection high energy electron diffraction (RHEED), x-ray diffraction (XRD), conventional transmission electron microscopy (CTEM), and high resolution transmission electron microscopy (HREM). XRD measurements exhibited a pronounced {100} texture. Employing electron diffraction in the TEM on cross sectional samples, we observed the following orientation relationship between Al and MgO: (100)A1 II (100)MgO; [010]A1 II [010]MgO. The atomistic structure of the interface was investigated by HREM. Regions of structural defects can be identified clearly at the interface.

Improving transmission electron microscopy characterization of semiconductors by minimizing sample preparation artifacts

1992 ◽  
Vol 70 (10-11) ◽  
pp. 875-880 ◽  
Author(s):  
J. P. McCaffrey ◽  
G. I. Sproule ◽  
R. Sargent
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Ion Milling ◽  
Transmission Electron ◽  
Transmission Electron Microscopy Characterization ◽  
Silicon Based ◽  
Microscopy Characterization ◽  
Preparation Techniques

Techniques employed for the preparation of transmission electron microscopy (TEM) samples can introduce artifacts that obscure subtle detail in the materials being studied. Traditional semiconductor sample preparation techniques rely heavily on ion milling, which leaves amorphous layers on ion milled surfaces and some intermixing across interfaces, thus degrading the TEM images of these samples. Experimental results of the extent of this amorphization and intermixing are presented for silicon-based semiconductor samples, and methods to minimize these effects are suggested. These methods include variations in ion milling parameters that reduce the extent of the artifacts, and improvements in the small-angle cleavage technique that eliminate these artifacts completely.

Sign in / Sign up

Export Citation Format

Share Document