Efficiency of Limestone Powder in SCC

2012 ◽  
Vol 1488 ◽  
Author(s):  
K. Ganesh Babu ◽  
B. Chandra Sekhar
Keyword(s):  
Compressive Strength ◽  
Mechanical Strength ◽  
Mineral Admixture ◽  
Strength Characteristics ◽  
Limestone Powder ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Topical Interest

ABSTRACTSelf-compacting concretes have been of topical interest due to the ease of adoption and the significant savings in compaction efforts particularly at the congested reinforcement locations, in spite of the leak-proof forms required. However, many of the aspects regarding their production with different powder or pozzolanic additions and their corresponding mechanical strength characteristics are not yet fully understood. This paper deals exclusively with the compressive strength characteristics of these concretes incorporating limestone powder as a mineral admixture through the water cement ratio to strength results of concretes reported in literature. The basic idea is to get an idea of the SCCs at the lowest and the highest possible amounts of the limestone powder in it.

Research on Static Compressive Experiment of Concrete Mixed with Limestone Power and Fly Ash

2013 ◽  
Vol 405-408 ◽  
pp. 2801-2805
Author(s):  
Ji Feng Liang ◽  
Lei Lv ◽  
Feng Wang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Test Method ◽  
Limestone Powder ◽  
Experimental Result ◽  
Enhancement Effect ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Orthogonal Test Method ◽  
Powder Content

The use of orthogonal test method, the concrete mixed with limestone power and fly ash was carried out static compressive experiment, and contrast with the experiment of single doped with limestone powder and fly ash concrete. The experimental result demonstrated that the compressive strength enhancement effect of the concrete mixed with limestone power and fly ash was obvious. The importance of each factor affecting static compressive strength as follows: water-cement ratio, the amount of fly ash, the amount of limestone powder, sand ratio. The concrete compressive strength reached the maximum when the water-cement ratio reached 0.3, the limestone powder content reached 15%, the fly ash content reached 10%, and sand ratio reached 34%.

scholarly journals Strength Characteristics of Groundnut Leaf/Stem Ash (GLSA) Concrete

2016 ◽  
Vol 24 (3) ◽  
pp. 36-43
Author(s):  
O. W. Oseni ◽  
M. T. Audu
Keyword(s):  
Compressive Strength ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Partial Replacement ◽  
Structural Elements ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Coarse Aggregates ◽  
Flow Test ◽  
Pozzolanic Properties

Abstract The compressive strength properties of concrete are substantial factors in the design and construction of concrete structures. Compressive strength directly affects the degree to which the concrete can be able to carry a load over time. These changes are complemented by deflections, cracks etc., in the structural elements of concrete. This research investigated the effect of groundnut leaf/stem ash (GLSA) on the compressive strength of concrete at 0%, 5 %, 10 % and 15 % replacements of cement. The effect of the water-cement ratio on properties such as the compressive strength, slump, flow and workability properties of groundnut leaf/stem ash (GLSA) mixes with OPC were evaluated to determine whether they are acceptable for use in concrete structural elements. A normal concrete mix with cement at 100 % (i.e., GLSA at 0%) with concrete grade C25 that can attain an average strength of 25 N/mm2 at 28 days was used as a control at design water-cement ratios of 0.65 and grading of (0.5-32) mm from fine to coarse aggregates was tested for: (1) compressive strength, and the (2) slump and flow Test. The results and observations showed that the concrete mixes from GLSA at 5 – 15 % ratios exhibit: pozzolanic properties and GLSA could be used as a partial replacement for cement at these percentage mix ratios compared with the control concrete; an increase in the water-cement ratio showed a significant decrease in the compressive strength and an increase in workability. Therefore, it is important that all concrete mixes exude an acceptably designed water-cement ratio for compressive strength characteristics for use in structures, water-cement ratio is a significant factor.

scholarly journals Use of Nondestructive Testing of Ultrasound and Artificial Neural Networks to Estimate Compressive Strength of Concrete

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 44
Author(s):  
Fernando A. N. Silva ◽  
João M. P. Q. Delgado ◽  
Rosely S. Cavalcanti ◽  
António C. Azevedo ◽  
Ana S. Guimarães ◽  
...  
Keyword(s):  
Neural Networks ◽  
Compressive Strength ◽  
Artificial Neural Networks ◽  
Cross Sections ◽  
Influential Factors ◽  
Average Error ◽  
Ann Model ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Artificial Neural

The work presents the results of an experimental campaign carried out on concrete elements in order to investigate the potential of using artificial neural networks (ANNs) to estimate the compressive strength based on relevant parameters, such as the water–cement ratio, aggregate–cement ratio, age of testing, and percentage cement/metakaolin ratios (5% and 10%). We prepared 162 cylindrical concrete specimens with dimensions of 10 cm in diameter and 20 cm in height and 27 prismatic specimens with cross sections measuring 25 and 50 cm in length, with 9 different concrete mixture proportions. A longitudinal transducer with a frequency of 54 kHz was used to measure the ultrasonic velocities. An ANN model was developed, different ANN configurations were tested and compared to identify the best ANN model. Using this model, it was possible to assess the contribution of each input variable to the compressive strength of the tested concretes. The results indicate an excellent performance of the ANN model developed to predict compressive strength from the input parameters studied, with an average error less than 5%. Together, the water–cement ratio and the percentage of metakaolin were shown to be the most influential factors for the compressive strength value predicted by the developed ANN model.

Study on Preparation of Solid Concrete Brick with Recycled Aggregate

2013 ◽  
Vol 648 ◽  
pp. 108-111
Author(s):  
Qi Jin Li ◽  
Guo Zhong Li
Keyword(s):  
Compressive Strength ◽  
Mass Fraction ◽  
Recycled Aggregate ◽  
Preparation Process ◽  
Mass Ratio ◽  
Construction Waste ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Optimal Value

The construction waste was processed into recycled aggregate to produce solid construction waste brick with grade of MU20. The preparation process of recycled aggregate and the optimal value of mass ratio of water to cement (water cement ratio) and mass ratio of recycled aggregate to cement was studied. The results shows that when the water cement ratio is 0.86 and the mass ratio of recycled aggregate to cement is 5.5 and the dosage of activator is 0.25% (mass fraction with recycled aggregate), the compressive strength of sample is 22.5MPa and can be satisfied with the requirement of MU20 solid concrete brick.

scholarly journals Influence of Aggregate Gradation on the Engineering Properties of Lightweight Aggregate Concrete

2018 ◽  
Vol 8 (8) ◽  
pp. 1324 ◽  
Author(s):  
How-Ji Chen ◽  
Chung-Hao Wu
Keyword(s):  
Compressive Strength ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Engineering Properties ◽  
Lightweight Aggregate Concrete ◽  
Aggregate Gradation ◽  
Aggregate Concrete ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Expanded Shale

Expanded shale lightweight aggregates, as the coarse aggregates, were used to produce lightweight aggregate concrete (LWAC) in this research. At the fixed water-cement ratio, paste quantity, and aggregate volume, the effects of various aggregate gradations on the engineering properties of LWAC were investigated. Comparisons to normal-weight concrete (NWC) made under the same conditions were carried out. From the experimental results, using normal weight aggregates that follow the specification requirements (standard gradation) obtained similar NWC compressive strength to that using uniform-sized aggregates. However, the compressive strength of LWAC made using small uniform-sized aggregates was superior to that made from standard-grade aggregates. This is especially conspicuous under the low water-cement ratio. Even though the workability was affected, this problem could be overcome with developed chemical additive technology. The durability properties of concrete were approximately equal. Therefore, it is suggested that the aggregate gradation requirement of LWAC should be distinct from that of NWC. In high strength LWAC proportioning, following the standard gradation suggested by American Society for Testing and Materials (ASTM) is optional.

Research on Simulation Test of Coal Similar Material

2013 ◽  
Vol 850-851 ◽  
pp. 847-850 ◽  
Author(s):  
Lin Chao Dai
Keyword(s):  
Compressive Strength ◽  
Raw Materials ◽  
Similarity Theory ◽  
Design Method ◽  
Uniform Design ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Similar Material ◽  
Cement Ratio ◽  
Water Cement Ratio

In order to study the coal and gas outburst similar simulation experiment, coal similar material was made up based on the similarity theory. Based on the previous similar material study, the cement, sand, water, activated carbon and coal powder was selected as the raw material of similar material. Meanwhile similar material matching program with 5 factors and 6 levels was designed by using Uniform Design Method. And the physical and mechanical properties of the similar material compressive strength was measured under different proportions circumstances. The relationship between similar material and the raw materials was analyzed. The results show that choosing different materials can compound different similar materials with different requirements. And the water-cement ratio plays a decisive influence on the compressive strength of similar material. The compressive strength of similar material decreases linearly when the water-cement ratio increases.

scholarly journals Effect of Mound Soil on Concrete Produced with River Sand

2014 ◽  
Vol 2 (1) ◽  
pp. 75-82
Author(s):  
Elivs M. Mbadike ◽  
N.N Osadebe
Keyword(s):  
Compressive Strength ◽  
Research Work ◽  
Strength Test ◽  
Control Test ◽  
River Sand ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Compressive Strength Test ◽  
Average Compressive Strength

In this research work, the effect of mound soil on concrete produced with river sand was investigated. A mixed proportion of 1.1.8:3.7 with water cement ratio of 0.47 were used. The percentage replacement of river sand with mound soil is 0%, 5%, 10%, 20%, 30% and 40%. Concrete cubes of 150mm x 150mm x150mm of river sand/mound soil were cast and cured at 3, 7, 28, 60 and 90 days respectively. At the end of each hydration period, the three cubes for each hydration period were crushed and their average compressive strength recorded. A total of ninety (90) concrete cubes were cast. The result of the compressive strength test for 5- 40% replacement of river sand with mound soil ranges from 24.00 -42.58N/mm2 a against 23.29-36.08N/mm2 for the control test (0% replacement).The workability of concrete produced with 5- 40% replacement of river sand with mound soil ranges from 47- 62mm as against 70mm for the control test.

scholarly journals Effect of Water Cement Ratios on Compressive Strength of Palm Kernel Shell Concrete

2019 ◽  
Vol 2 (Issue 1) ◽  
Author(s):  
A.O Adeyemi ◽  
M.A Anifowose ◽  
I.O Amototo ◽  
S.A Adebara ◽  
M.Y Olawuyi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Palm Kernel ◽  
Hardened Concrete ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Palm Kernel Shell ◽  
Compressive Strength Of Concrete ◽  
Palm Kernel Shells

This study examined the effect of varying water cement ratio on the compressive strength of concrete produced using palm kernel shell (PKS) as coarse aggregate at different replacement levels. The replacement levels of coarse aggregate with palm kernel shells (PKS) were 0%, 25%, 50%, and 100% respectively. PKS concrete cubes (144 specimens) of sizes 150mm x 150mm x 150mm were cast and cured in water for 7, 14, 21 and 28 days respectively. A mix ratio of 1:2:4 was adopted with water-cement ratio of 0.45, 0.5, and 0.6 respectively while the batching was done by weight. Slump test was conducted on fresh concrete while compressive strength test was carried out on the hardened concrete cubes using a compression testing machine of 2000kN capacity. The result of tests on fresh concrete shows that the slump height of 0.45 water cement ratio (w/c) increases with an increase in PKS%. This trend was similar to 0.50 and 0.60 w/c. However, the compressive strength of concrete cube decreases with an increase in w/c (from 0.45 to 0.60) but increases with respect to curing age and also decreases with increase in PKS%. Concrete with 0.45 water-cement ratio possess the highest compressive strength. It was observed that PKS is not a good substitute for coarse aggregate in mix ratio 1:2:4 for concrete productions. Hence, the study suggest the use of chemical admixture such as superplasticizer or calcium chloride in order to improve the strength of palm kernel shells-concrete.

scholarly journals Mechanical Properties of Concrete with Various Water-Cement Ratio After High Temperature Exposure

2019 ◽  
Vol 2 (2) ◽  
pp. 126-136
Author(s):  
M.I Retno Susilorini ◽  
Budi Eko Afrianto ◽  
Ary Suryo Wibowo
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Modulus Of Elasticity ◽  
Building Materials ◽  
Heating Process ◽  
High Temperature Exposure ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Temperature Exposure

Concrete building safety of fire is better than other building materials such as wood, plastic, and steel,because it is incombustible and emitting no toxic fumes during high temperature exposure. However,the deterioration of concrete because of high temperature exposure will reduce the concrete strength.Mechanical properties such as compressive strength and modulus of elasticity are absolutely corruptedduring and after the heating process. This paper aims to investigate mechanical properties of concrete(especially compressive strength and modulus of elasticity) with various water-cement ratio afterconcrete suffered by high temperature exposure of 500oC.This research conducted experimental method and analytical method. The experimental methodproduced concrete specimens with specifications: (1) specimen’s dimension is 150 mm x 300 mmconcrete cylinder; (2) compressive strength design, f’c = 22.5 MPa; (3) water-cement ratio variation =0.4, 0.5, and 0.6. All specimens are cured in water for 28 days. Some specimens were heated for 1hour with high temperature of 500oC in huge furnace, and the others that become specimen-controlwere unheated. All specimens, heated and unheated, were evaluated by compressive test.Experimental data was analyzed to get compressive strength and modulus of elasticity values. Theanalytical method aims to calculate modulus of elasticity of concrete from some codes and to verifythe experimental results. The modulus elasticity of concrete is calculated by 3 expressions: (1) SNI03-2847-1992 (which is the same as ACI 318-99 section 8.5.1), (2) ACI 318-95 section 8.5.1, and (3)CEB-FIP Model Code 1990 Section 2.1.4.2.The experimental and analytical results found that: (1) The unheated specimens with water-cementratio of 0.4 have the greatest value of compressive strength, while the unheated specimens with watercementratio of 0.5 gets the greatest value of modulus of elasticity. The greatest value of compressivestrength of heated specimens provided by specimens with water-cement ratio of 0.5, while the heatedspecimens with water-cement ratio of 0.4 gets the greatest value of modulus of elasticity, (2) Allheated specimens lose their strength at high temperature of 500oC, (3) The analytical result shows thatmodulus of elasticity calculated by expression III has greater values compares to expression I and II,but there is only little difference value among those expressions, and (4)The variation of water-cementratio of 0.5 becomes the optimum value.

scholarly journals The Influence of Finely Ground Mineral Admixture (FGMA) on Efflorescence

2013 ◽  
Vol 4 (1) ◽  
pp. 50-55 ◽  
Author(s):  
Ong Ming Wei ◽  
Norsuzailina Mohamed Sutan
Keyword(s):  
Calcium Carbonate ◽  
Chemical Analysis ◽  
Mineral Admixture ◽  
Partial Replacement ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Cement Replacement ◽  
Carbonate Formation

Efflorescence phenomenon on concrete is not new and found in the form of white deposits on surfaces of concrete. Incorporation of Finely Ground Mineral Admixture (FGMA) in concrete to prevent occurrence of efflorescence is based on reduction of portlandite, densified microstructure and thus enhanced watertightness. The magnitude of efflorescence in term of percentage of calcium carbonate formation of FGMA modified mortar were evaluated at water-cement ratio of 0.3, 0.4 and 0.5 with 10%, 20%, and 30% of cement replacement by weight. The samples were tested with chemical analysis at 7, 14, 21, 28, 60 and 90 days. The FGMA additions into mortar were comparing with ordinary mortar to evaluate enhanced performance of FGMA modified mortar toward efflorescence. The results of this experiment showed that addition of FGMA into mortar caused less formation of calcium carbonate as partial replacement of cement with certain w/c ratio and percentage of cement replacement.

Sign in / Sign up

Export Citation Format

Share Document