Thermal and viscoelastic behaviors of nanotube-reinforced polyethylene composite

2011 ◽  
Vol 1312 ◽  
Author(s):  
Ananta Raj Adhikari ◽  
Mircea Chipara ◽  
Karen Lozano
Keyword(s):  
Mechanical Property ◽  
Thermal Stability ◽  
Mechanical Behavior ◽  
Storage Modulus ◽  
Polymer Matrix ◽  
Loss Modulus ◽  
Polyethylene Composite ◽  
Viscoelastic Behaviors ◽  
Thermal Stability Of

ABSTRACTThe effect of processing (shear) time on the mechanical behavior and thermal stability of multiwalled nanotube reinforced polyethylene was investigated. It was observed that the mechanical property (storage modulus, loss modulus) of the composites is process dependant whereas the thermal stability does not. The increase in mechanical behavior is attributed to a stronger interface between the nanotube and the polymer matrix.

scholarly journals The Influence of Mercerised Kenaf Fibres Reinforced Polylactic Acid Composites on Dynamic Mechanical Analysis

2011 ◽  
Vol 471-472 ◽  
pp. 815-820 ◽  
Author(s):  
Rosnita A. Talib ◽  
Intan Syafinaz Mohamed Amin Tawakkal ◽  
Abdan Khalina
Keyword(s):  
Thermal Stability ◽  
Polylactic Acid ◽  
Storage Modulus ◽  
Loss Modulus ◽  
Dry Weight ◽  
Compression Moulding ◽  
Melt Mixing ◽  
Dynamic Mechanical ◽  
Thermal Stability Of ◽  
Kenaf Fibres

The potential of using cellulose to reinforce the thermal stability of kenaf derived cellulose (KDC)/polylactic acid (PLA) composite was investigated in this study. The cellulose was derived from kenaf bast fibre which was chemically treated via chlorination and mercerisation processes. The composites with various loadings of cellulose (dry weight basis) ranging from 0% to 60% were produced by melt mixing and compression moulding. Dynamic mechanical properties namely storage modulus (E’), loss modulus (E”) and tan δ of the KDC/PLA composites and the commercial PLA were analysed and compared as a function of temperature. ESEM micrographs demonstrated that the mercerisation of kenaf fibres have successfully removed the lignin and hemicellulose, thus producing cellulose which can be observed by its rougher surface and greater size reduction than the raw fibre. The DMA results demonstrated that the storage modulus of 60% KDC/PLA composite is twice higher than the commercial PLA and the rest of the composites within a high temperature range (above 80°C). The glass transition temperatures (Tg) generated from the loss modulus curves exhibit that the peak of the loss modulus was shifted to higher temperature as the percentage of the cellulose loading was increased. These results show a better thermal stability of the composites when incorporated with the cellulose.

Effect of the hydrophilicity of the polymer matrix on immobilized α-chymotrypsin

1984 ◽  
Vol 49 (6) ◽  
pp. 1552-1556
Author(s):  
Minoru Kumakura ◽  
Isso Kaetsu
Keyword(s):  
Thermal Stability ◽  
Enzyme Activity ◽  
Pore Size ◽  
Polymer Matrix ◽  
Low Temperatures ◽  
Radiation Polymerization ◽  
Thermal Stability Of

α-Chymotrypsin was immobilized by radiation polymerization at low temperatures and the effect of the hydrophilicity of the polymer matrix on the enzyme activity and thermal stability was studied. The activity and thermal stability of immobilized chymotrypsin increased with the increasing hydrophilicity of the polymer matrix or monomer. The thermal stability was affected by the form and pore size of the polymer matrix; chymotrypsin immobilized on a soft-gel polymer matrix exhibited an enhanced thermal stability.

Effect of Fumed Silica and Zinc Borate on the Thermogravimetric Analysis Curves of ABS/Magnesium Hydroxide Composite

2014 ◽  
Vol 599-601 ◽  
pp. 183-186
Author(s):  
Zhang Ting Li ◽  
Yue Qun Lu ◽  
Li Li Fan ◽  
Pei Bang Dai ◽  
Xia Su ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Thermal Stability ◽  
Flame Retardant ◽  
Fumed Silica ◽  
Acrylonitrile Butadiene Styrene ◽  
Zinc Borate ◽  
Processing Temperature ◽  
Great Decrease ◽  
Thermal Stability Of ◽  
Butadiene Styrene

For achieving sufficient flame retardancy, high magnesim hydroxide (MH) content is needed in MH flame retardant Acrylonitrile-butadiene-styrene copolymer (ABS) composites (ABS/MH), which will cause a great decrease in mechanical property and difficulty in preparing samples for measurement. We prepared ABS/MH filled high 60.0% flame retardant by compounding ABS and modified flame retardant MH, fumed silica (SiO2) and zinc borate (ZB) via TX-10 phosphate/polyacrylate latex and studied the effect of a small amount of SiO2 and ZB with MH in ABS for improving the thermal decomposition of ABS/MH. The thermal stability of the modified flame retardant could meet the processing temperature of ABS. The incorporation of ZB, SiO2 or SiO2/ZB could improve the thermal stability of ABS/MH.

scholarly journals Effect of Compatibilizer on the Interface Bonding of Graphene Oxide/Polypropylene Composite Fibers

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1283 ◽  
Author(s):  
Miao Miao ◽  
Chunyan Wei ◽  
Ying Wang ◽  
Yongfang Qian
Keyword(s):  
Thermal Stability ◽  
Graphene Oxide ◽  
Loss Modulus ◽  
Composite Fiber ◽  
Mechanical Analysis ◽  
Interfacial Bonding ◽  
Composite Fibers ◽  
Scanning Calorimetry ◽  
Blending Method ◽  
Thermal Stability Of

To improve the interfacial bonding and thermal stability of graphene oxide (GO)/polypropylene (PP) composite fibers, a composite fiber with PP as the matrix, GO as reinforcement and maleic anhydride-grafted PP (PP-g-MAH) as a compatibilizer was prepared by a simple and efficient melt-blending method. The GO content was 0.0–5.0 wt %. According to the Fourier Transform Infrared (FT-IR) spectroscopy results, the interfacial bonding in the PP/MAH/GO composite fibers was improved. The Dynamic Mechanical Analysis (DMA) results show that the addition of GO resulted in better interfacial adhesion and higher storage modulus (E′). The loss modulus (E′′) of the PP/MAH/GO-x composite fibers increased with increasing amount of added GO, whereas the loss factor (tan δ) decreased. GO and PP-g-MAH were analyzed by Thermogravimetric Analysis (TGA). The thermal stability of the composite fibers was improved compared to PP. Differential Scanning Calorimetry (DSC) analysis showed that the addition of PP-g-MAH to the composite fiber improved the interfacial bonding of GO in the PP matrix. Thus, compatibility between the two components was obtained. Based on the Scanning Electron Microscopy (SEM) results, the PP fibers exhibited relative orientation due to the strong crystalline morphology. The rough section, PP/GO blend fiber exhibits a very clear phase separation morphology due to the incompatibility between the two and the compatibility of GO and PP in PP/MAH/GO-3 composite fiber is improved, resulting in the interface between the two has improved.

Sign in / Sign up

Export Citation Format

Share Document