Formation and characterization of germanium nanoparticles

2000 ◽  
Vol 15 (11) ◽  
pp. 2400-2407 ◽  
Author(s):  
N. J. Welham
Keyword(s):  
Raman Spectroscopy ◽  
Crystallite Size ◽  
Magnesium Oxide ◽  
Phonon Confinement ◽  
X Ray Diffraction ◽  
Acid Leach ◽  
Crystallite Sizes ◽  
Crystal Core ◽  
Individual Particles

Elemental germanium was mechanically milled with magnesium oxide with the intention of forming disperse nanoparticulate germanium in a soluble matrix. The crystallite size was determined by x-ray diffraction (XRD) and Raman spectroscopy using a phonon confinement model. The crystallite size was found to decrease exponentially with milling time; however, the size determined by XRD was typically five to ten times greater than that by Raman. This was attributed to the presence of two separate crystallite sizes, which were averaged when using the Scherrer equation for the XRD data. Sonication of the powder resulted in the breakup of >20 μm aggregates into individual particles of approximately 40 nm. These particles are thought to compose a single crystal core with a crystallite size of approximately 28 nm surrounded by a layer of smaller crystallites (approximately 5 nm), which showed quantization during Raman spectroscopy. Separation of the germanium from the magnesium oxide was readily achieved using a simple acid leach, although some oxidation of germanium was evident when using an aqueous leach.

Synthesis and Characterisation of Titania Nanotubes: Effect of Phase and Crystallite Size on Nanotube Formation

2007 ◽  
Vol 29-30 ◽  
pp. 211-214 ◽  
Author(s):  
D.L. Morgan ◽  
E.R. Waclawik ◽  
R.L Frost
Keyword(s):  
Raman Spectroscopy ◽  
Crystallite Size ◽  
Electron Spectroscopy ◽  
Driving Force ◽  
Titania Nanotubes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Material Type ◽  
Transmission Electron ◽  
Crystallite Sizes

Nanotubes were produced from commercial and self-prepared anatase and rutile which were treated with 7.5 M NaOH over a temperature range of 100 – 200°C in 20°C increments. The formation of nanotubes was examined as a function of starting material type and size. Products were characterised by X-Ray Diffraction (XRD), Transmission Electron Spectroscopy (TEM), and Raman Spectroscopy. The results indicated that both phase and crystallite size affected the nanotube formation. Rutile was observed to require a greater driving force than anatase to form nanotubes, and increases in crystallite sizes appeared to impede formation slightly.

Deposition of TRISO Particles With Superhard SiC Coatings and the Characterization of Anisotropy by Raman Spectroscopy

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
E. López-Honorato ◽  
P. J. Meadows ◽  
J. Tan ◽  
Y. Xiang ◽  
P. Xiao
Keyword(s):  
Solid Solution ◽  
Raman Spectroscopy ◽  
Pyrolytic Carbon ◽  
X Ray Diffraction ◽  
X Ray ◽  
Flat Substrate ◽  
High Concentrations ◽  
Triso Particles ◽  
Sic Coatings

In this work we have deposited silicon carbide (SiC) at 1300°C with the addition of small amounts of propylene. The use of propylene and high concentrations of methyltrichlorosilane (9 vol %) allowed the deposition of superhard SiC coatings (42 GPa). The superhard SiC could result from the presence of a SiC–C solid solution, undetectable by X-ray diffraction but visible by Raman spectroscopy. Another sample obtained by the use of 50 vol % Argon, also showed the formation of SiC with good properties. The use of a flat substrate together with the particles showed the importance of carrying out the analysis on actual particles rather than in flat substrates. We show that it is possible to characterize the anisotropy of pyrolytic carbon by Raman spectroscopy.

scholarly journals Characterization of Cobalt Sulfide Thin Films Synthesized from Acidic Chemical Baths

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Tizazu Abza ◽  
Dereje Gelanu Dadi ◽  
Fekadu Gashaw Hone ◽  
Tesfaye Chebelew Meharu ◽  
Gebremeskel Tekle ◽  
...  
Keyword(s):  
Thin Films ◽  
Crystallite Size ◽  
Deposition Time ◽  
Average Crystallite Size ◽  
Cobalt Sulfide ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Electron Microscopic ◽  
Face Centered

Cobalt sulfide thin films were synthesized from acidic chemical baths by varying the deposition time. The powder X-ray diffraction studies indicated that there are hexagonal CoS, face-centered cubic Co3S4, and cubic Co9S8 phases of cobalt sulfide. The crystallite size of the hexagonal CoS phase decreased from 52.8 nm to 22.5 nm and that of the cubic Co9S8 phase increased from 11 nm to 60 nm as the deposition time increased from 2 hrs to 3.5 hrs. The scanning electron microscopic images revealed crack and pinhole free thin films with uniform and smooth background and few large polygonal grains on the surface. The band gap of the cobalt sulfide thin films decreased from 1.75 eV to 1.3 eV as the deposition time increased from 2 hrs to 3.5 hrs. The photoluminescence (PL) spectra of the films confirmed the emission of ultraviolet, violet, and blue lights. The intense PL emission of violet light at 384 nm had red shifted with increasing deposition time that could be resulted from the increase in the average crystallite size. The FTIR spectra of the films indicated the presence of OH, C-O-H, C-O, double sulfide, and Co-S groups. As the deposition time increased, the electrical resistivity of the cobalt sulfide thin films decreased due to the increase in both the crystallite size and the films’ thickness.

scholarly journals Structural and morphological characterization of rare earth modified lead titanate

Cerâmica ◽  
2007 ◽  
Vol 53 (328) ◽  
pp. 422-447
Author(s):  
F. C. D. Lemos ◽  
D. M. A. Melo ◽  
P. S. de Lima ◽  
C. A. Paskocimas ◽  
E. Longo ◽  
...  
Keyword(s):  
Rare Earth ◽  
Lead Titanate ◽  
Pechini Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Crystallite Sizes ◽  
Modifier Cation

Rare earth modified lead titanate powders Pb1-xRExTiO3 (REPT), x = 0.01, 0.05, 0.07 and RE = Yb, Y, were prepared by the Pechini method. The materials were calcined under flowing oxygen at different temperatures from 300 to 700 ºC. Nanostructured REPT were investigated using X-ray diffraction, scanning electron microscopy and surface area analysis (BET). The results suggest that the modifier cation incorporated into the system has notable influence in the microstructure and a notable decrease in the crystallite sizes.

Thermal Silicidation of Ni/SiGe and Characterization of Resulting Silicide Films Using Raman Spectroscopy and X-ray Diffraction

2020 ◽  
Vol 98 (5) ◽  
pp. 457-464
Author(s):  
Woo Sik Yoo ◽  
Kitaek Kang ◽  
Toshikazu Ishigaki ◽  
Jung Gon Kim ◽  
Noriyuki Hasuike ◽  
...  
Keyword(s):  
Raman Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray

X-ray diffraction Warren–Averbach mullite analysis in whiteware porcelains: influence of kaolin raw material

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 471-485 ◽  
Author(s):  
Angel Sanz ◽  
Joaquín Bastida ◽  
Angel Caballero ◽  
Marek Kojdecki
Keyword(s):  
Crystallite Size ◽  
Firing Temperature ◽  
Microstructural Analysis ◽  
Stoichiometric Composition ◽  
Raw Material ◽  
Size Distributions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Crystallite Sizes

ABSTRACTCompositional and microstructural analysis of mullites in porcelain whitewares obtained by the firing of two blends of identical triaxial composition using a kaolin B consisting of ‘higher-crystallinity’ kaolinite or a finer halloysitic kaolin M of lower crystal order was performed. No significant changes in the average Al2O3 contents (near the stoichiometric composition 3:2) of the mullites were observed. Fast and slow firing at the same temperature using B or M kaolin yielded different mullite contents. The Warren–Averbach method showed increase of the D110 mullite crystallite size and crystallite size distributions with small shifts to greater values with increasing firing temperature for the same type of firing (slow or fast) using the same kaolin, as well as significant differences between fast and slow firing of the same blend at different temperatures for each kaolin. The higher maximum frequency distribution of crystallite size observed at the same firing temperature using blends with M kaolin suggests a clearer crystallite growth of mullite in this blend. The agreement between thickening perpendicular to prism faces and mean crystallite sizes <D110> of mullite were not always observed because the direction perpendicular to 110 planes is not preferred for growth.

Corroboration of Structural Properties of Dy2O3-TiO2 Nanocomposites through X-Ray Diffraction and Raman Spectroscopy

2017 ◽  
Vol 17 ◽  
pp. 127-130
Author(s):  
J. Dhanalakshmi ◽  
D. Pathinettam Padiyan
Keyword(s):  
Raman Spectroscopy ◽  
Crystallite Size ◽  
Structural Properties ◽  
Oxygen Vacancies ◽  
Raman Band ◽  
Anatase Phase ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Weight Percentage

Dy2O3-TiO2 nanocomposites with different weight percentage (0, 2, 4, 8 & 10)Dy were synthesized bysol-gel method and named as 0DT, 2DT, 4DT, 6DT, 8DT and 10DT. The structural properties of these nanocomposites are characterized by X-ray diffraction (XRD) and Raman spectroscopy. XRD results show that Dy2O3-TiO2 nanocomposites have anatase phase with tetragonal structure. The average crystallite size of the Dy2O3-TiO2 nanocomposites lies between 10 to 18 nm.Coupling of Dy with TiO2 shifts the Raman band to higher wavenumber side indicating the creation of oxygen vacancies in the TiO2 lattice.

Low Temperature Synthesis and Characterization of CaO and MgO- Stabilized Nanocrystalline Tetragonal Zirconia by Citrate Gel Process

2008 ◽  
Vol 368-372 ◽  
pp. 754-757
Author(s):  
Hasan Gocmez ◽  
Hirotaka Fujimori
Keyword(s):  
Single Phase ◽  
Tetragonal Zirconia ◽  
Xrd Analysis ◽  
Complex Method ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Heat Treated ◽  
Crystallite Sizes ◽  
Citrate Gel Process

The citrate gel method, similar to the polymerized complex method, was used to synthesize homogenous tetragonal zirconia at 800oC and 1000oC. Nanocrystalline tetragonal single phase has been fully stabilized with 3, 7, 10 mol% CaO and 10, 15 mol% MgO at 800oC, respectively. In addition, the XRD analysis showed the absence of monoclinic phase after addition of 7 and 10 mol% CaO into zirconia-based solid solutions, which have been fully stabilized both 800oC and 1000oC. The crystallite sizes of the t-ZrO2 with 3, 7 and 10 mol% CaO at 1000oC were 32, 28 and 29nm, respectively. For ZrO2- x mol% MgO (x=3, 10, 15) solid solution, the crystallite sizes of samples at 800oC were less than 29nm, however it was increased up to 69nm at 1000oC. The prepared gel and subsequent heat-treated powders were characterized by X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy (TEM) to get detail information regarding to differentiation of polymorphs of zirconia as well as formation of powders.

Production and Characterization of Carbon Thin Films by the Magnetron Sputtering Technique

2016 ◽  
Vol 881 ◽  
pp. 471-474 ◽  
Author(s):  
D.L.C. Silva ◽  
L.R.P Kassab ◽  
J.R. Martinelli ◽  
A.D. Santos ◽  
M.F. Pillis
Keyword(s):  
Thin Films ◽  
Raman Spectroscopy ◽  
Magnetron Sputtering ◽  
Carbon Film ◽  
Carbon Films ◽  
Buffer Layers ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Carbon Thin Films

Carbon thin films were produced by the magnetron sputtering technique. The deposition of the carbon films was performed on Co buffer-layers previously deposited on c-plane (0001) sapphire substrates. The samples were thermally treated under vacuum conditions and characterized by Raman spectroscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD). The XRD peak related to the carbon film was observed and the Raman spectroscopy indicated a good degree of crystallinity of the carbon film.

Sign in / Sign up

Export Citation Format

Share Document