Growth of halide perovskites thin films for thermoelectric applications

MRS Advances ◽  
2019 ◽  
Vol 4 (30) ◽  
pp. 1719-1725 ◽  
Author(s):  
Shrikant Saini ◽  
Ajay Kumar Baranwal ◽  
Tomohide Yabuki ◽  
Shuzi Hayase ◽  
Koji Miyazaki
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Cost Effective ◽  
Thermoelectric Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Halide Perovskites

ABSTRACTThermoelectric materials can play an important role to develop a sustainable energy source for internet of things devices near room temperature. In this direction, it is important to have a thermoelectric material with high thermoelectric performance. Cesium tin triiodide (CsSnI3) single crystal perovskite has shown high value of Seebeck coefficient and ultra low thermal conductivity which are necessary conditions for high thermoelectric performance. Here, we report the thermoelectric response of CsSnI3 thin films. These films are prepared by cost effective wet spin coating process at different baking temperature. Films were characterized using X-ray diffraction and scanning electron microscopy. In our case, films baked at 130°C for 5 min have shown the best thermoelectric performance at room temperature with: Seebeck coefficient 115 μV/K and electrical conductivity 124 S/cm, thermal conductivity 0.36 W/m·K and figure of merit ZT of 0.137.

scholarly journals Influence of Deposition Rate on the Thermoelectric Properties of Sb2Te3Thin Films by Thermal Evaporation Method

2015 ◽  
Vol 2015 ◽  
pp. 1-5 ◽  
Author(s):  
Jyun-Min Lin ◽  
Ying-Chung Chen ◽  
Wei Chen
Keyword(s):  
Thin Films ◽  
Seebeck Coefficient ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermal Evaporation ◽  
X Ray Diffraction ◽  
Thermal Evaporation Method ◽  
X Ray ◽  
Si Substrates ◽  
Cooling Devices

Thermoelectric (TE) materials are crucial because they can be used in power generation and cooling devices. Sb2Te3-based compounds are the most favorable TE materials because of their excellent figure of merit at room temperature. In this study, Sb2Te3thin films were prepared on SiO2/Si substrates through thermal evaporation. The influence of the evaporation current on the microstructures and TE properties of Sb2Te3thin films were investigated. The crystalline structures and morphologies of the thin films were analyzed using X-ray diffraction and field emission scanning electron microscopy. The Seebeck coefficient, electrical conductivity, and power factor (PF) were measured at room temperature. The experimental results showed that the Seebeck coefficient increased and conductivity decreased with increasing evaporation current. The Seebeck coefficient reached a maximum of 387.58 μV/K at an evaporation current of 80 A. Conversely, a PF of 3.57 µW/cmK2was obtained at room temperature with evaporation current of 60 A.

Unileg Thermoelectric Module Comprised by Coated Halide-Perovskite Thin Film

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Shrikant Saini ◽  
Ajay Kumar Baranwal ◽  
Tomohide Yabuki ◽  
Shuzi Hayase ◽  
Koji Miyazaki
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
Maximum Output Power ◽  
Thermoelectric Module ◽  
Direct Conversion ◽  
Maximum Output ◽  
X Ray Diffraction ◽  
X Ray

Abstract The direct conversion of thermal energy into electricity is possible by thermoelectric effect. CsSnI3 perovskite has shown a way with its intrinsic ultralow thermal conductivity and large Seebeck coefficient. In this work, CsSnI3 thin films were optimized. Thin films were structurally and chemically characterized using X-ray diffraction (XRD) and scanning electron microscope (SEM). Thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity were measured near room temperature (300 K). CsSnI3 thin films unileg thermoelectric modules were fabricated on a glass substrate. The maximum output power is obtained about 0.8 nW for five legs (25 mm × 3 mm × 600 nm) modules for the temperature difference of about 5 °C.

Long-term Room Temperature Instability in Thermal Conductivity of InGaZnO Thin Films

MRS Advances ◽  
2016 ◽  
Vol 1 (22) ◽  
pp. 1631-1636 ◽  
Author(s):  
Boya Cui ◽  
D. Bruce Buchholz ◽  
Li Zeng ◽  
Michael Bedzyk ◽  
Robert P. H. Chang ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Room Temperature ◽  
Storage Time ◽  
Laser Deposition ◽  
Low Oxygen ◽  
X Ray Diffraction ◽  
3Ω Method ◽  
X Ray

ABSTRACTThe cross-plane thermal conductivities of InGaZnO (IGZO) thin films in different morphologies were measured on three occasions within 19 months, using the 3ω method at room temperature 300 K. Amorphous (a-), semi-crystalline (semi-c-) and crystalline (c-) IGZO films were grown by pulsed laser deposition (PLD), followed by X-ray diffraction (XRD) for evaluation of film quality and crystallinity. Semi-c-IGZO shows the highest thermal conductivity, even higher than the most ordered crystal-like phase. After being stored in dry low-oxygen environment for months, a drastic decrease of semi-c-IGZO thermal conductivity was observed, while the thermal conductivity slightly reduced in c-IGZO and remained unchanged in a-IGZO. This change in thermal conductivity with storage time can be attributed to film structural relaxation and vacancy diffusion to grain boundaries.

Thermoelectric Performance of Glass Microsphere Dispersed Bi-Sb Composites at Low Temperature

2013 ◽  
Vol 743-744 ◽  
pp. 120-125
Author(s):  
Zhen Chen ◽  
Ye Mao Han ◽  
Min Zhou ◽  
Rong Jin Huang ◽  
Yuan Zhou ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Materials ◽  
Sem Analysis ◽  
Glass Microsphere ◽  
Thermoelectric Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Measurement Results

In the present study, the glass microsphere dispersed Bi-Sb thermoelectric materials have been fabricated through mechanical alloying followed by pressureless sintering. The phase composition and the microstructure were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis. Electrical conductivity, Seebeck coefficient and thermal conductivity were measured in the temperature range of 77~300 K. The ZT values were calculated according to the measurement results. The results showed that the electrical conductivity, Seebeck coefficient and thermal conductivity decreased by adding glass microsphere into Bi-Sb thermoelectric materials. However, the optimum ZT value of 0.24 was obtained at 260 K, which was increased 10% than that of the Bi-Sb matrix. So it is confirmed that the thermoelectric performance of Bi-Sb-based materials can be improved by adding moderate glass microspheres.

scholarly journals Thermoelectric Lead Telluride with ZnO Nanoparticles

2015 ◽  
Vol 16 (1) ◽  
pp. 62-67
Author(s):  
O. M. Matkivsky
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Figure Of Merit ◽  
Lead Telluride ◽  
Thermoelectric Figure Of Merit ◽  
X Ray Diffraction ◽  
Thermoelectric Figure ◽  
X Ray ◽  
Zno Powder

An X-ray diffraction structural study and measurement of Seebeck coefficient (S), the electrical conductivity (σ) and thermal conductivity (χ) for Lead Telluride with nanoinclusions of ZnO. The calculated value of the specific thermoelectric power (S2σ) and thermoelectric figure of merit (ZT). It was established that the addition of ZnO powder Nanodispersed diameter grains (40-60) nm PbTe reduces the thermal conductivity of the material, and at 0.5 wt.% ZnO to an increase of lead telluride thermoelectric figure of merit to ZT≈1,3.

High Thermoelectric Performance of p-Type Bi0.5Sb1.5Te3+xTe Crystals Prepared via Gradient Freezing

2012 ◽  
Vol 621 ◽  
pp. 167-171
Author(s):  
Tao Hua Liang ◽  
Shi Qing Yang ◽  
Zhi Chen ◽  
Qing Xue Yang
Keyword(s):  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Performance ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
P Type

p-type Bi0.5Sb1.5Te3+xTe thermoelectric crystals with various percentages of Te (x = 0.00 wt.%–3.00 wt.%) excess were prepared by the gradient freeze method. By doping with different Te contents, anti-site defects, Te vacancies and hole carrier concentrations were controlled. The Seebeck coefficient, resistivity, thermal conductivity, carrier concentration, and mobility were measured. The relationships between the Te content and thermoelectric properties were investigated in detail. The results suggested that the thermoelectric figure of merit ZT of the Bi0.5Sb1.5Te3+0.09wt.% crystals was 1.36 near room temperature, the optimum carrier concentration was 1.25 × 1019 cm-3, and the mobility was 1480 cm2 V-1 S-1, respectively.

Structure and Conductivity of Iodine-Doped C60 Thin Films

1994 ◽  
Vol 359 ◽  
Author(s):  
Jun Chen ◽  
Haiyan Zhang ◽  
Baoqiong Chen ◽  
Shaoqi Peng ◽  
Ning Ke ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Room Temperature ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Temperature Conductivity ◽  
Room Temperature Conductivity ◽  
X Ray ◽  
Thermally Activated ◽  
Order Of Magnitude

ABSTRACTWe report here the results of our study on the properties of iodine-doped C60 thin films by IR and optical absorption, X-ray diffraction, and electrical conductivity measurements. The results show that there is no apparent structural change in the iodine-doped samples at room temperature in comparison with that of the undoped films. However, in the electrical conductivity measurements, an increase of more that one order of magnitude in the room temperature conductivity has been observed in the iodine-doped samples. In addition, while the conductivity of the undoped films shows thermally activated temperature dependence, the conductivity of the iodine-doped films was found to be constant over a fairly wide temperature range (from 20°C to 70°C) exhibiting a metallic feature.

Thermoelectric Properties of Semiconducting Intermetallic Compounds: FeGa3and RuGa3

2003 ◽  
Vol 793 ◽  
Author(s):  
Y. Amagai ◽  
A. Yamamoto ◽  
C. H. Lee ◽  
H. Takazawa ◽  
T. Noguchi ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
High Temperature ◽  
Seebeck Coefficient ◽  
Transport Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
High Seebeck Coefficient

ABSTRACTWe report transport properties of polycrystalline TMGa3(TM = Fe and Ru) compounds in the temperature range 313K<T<973K. These compounds exhibit semiconductorlike behavior with relatively high Seebeck coefficient, electrical resistivity, and Hall carrier concentrations at room temperature in the range of 1017- 1018cm−3. Seebeck coefficient measurements reveal that FeGa3isn-type material, while the Seebeck coefficient of RuGa3changes signs rapidly from large positive values to large negative values around 450K. The thermal conductivity of these compounds is estimated to be 3.5Wm−1K−1at room temperature and decreased to 2.5Wm−1K−1for FeGa3and 2.0Wm−1K−1for RuGa3at high temperature. The resulting thermoelectric figure of merit,ZT, at 945K for RuGa3reaches 0.18.

Synthesis of CaWO4:(Eu3+,Tb3+) Thin Films by a Two-Step Method at Room Temperature

2013 ◽  
Vol 710 ◽  
pp. 170-173
Author(s):  
Lian Ping Chen ◽  
Yuan Hong Gao
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Phase Composition ◽  
Room Temperature ◽  
Electrochemical Techniques ◽  
Luminescent Properties ◽  
X Ray Diffraction ◽  
Step Method ◽  
X Ray ◽  
Rare Earth Doped

It is hardly possible to obtain rare earth doped CaWO4thin films directly through electrochemical techniques. A two-step method has been proposed to synthesize CaWO4:(Eu3+,Tb3+) thin films at room temperature. X-ray diffraction, energy dispersive X-ray analysis, spectrophotometer were used to characterize their phase, composition and luminescent properties. Results reveal that (Eu3+,Tb3+)-doped CaWO4films have a tetragonal phase. When the ratio of n (Eu)/n (Tb) in the solution is up to 3:1, CaWO4:(Eu3+,Tb3+) thin film will be enriched with Tb element; on the contrary, when the ratio in the solution is lower than 1:4, CaWO4:(Eu3+,Tb3+) thin film will be enriched with Eu element. Under the excitation of 242 nm, sharp emission peaks at 612, 543, 489 and 589 nm have been observed for CaWO4:(Eu3+,Tb3+) thin films.

N-type Ba0.2Co4Sb11.5Te0.5: Optimization of thermoelectric properties by different pressures

2019 ◽  
Vol 33 (03) ◽  
pp. 1950027 ◽  
Author(s):  
Jiaxiang Chen ◽  
Xiaopeng Jia ◽  
Yuewen Zhang ◽  
Haiqiang Liu ◽  
Baomin Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Absolute Value ◽  
X Ray ◽  
Coefficient Increase ◽  
Maximum Power Factor ◽  
Scanning Electron

The polycrystalline skutterudite [Formula: see text] were successfully synthesized from 1.5 GPa to 3.5 GPa by the high pressure and high temperature (HPHT) method. Negative Seebeck coefficient confirmed the n-type conductivity of all samples. The phase compositions of samples were investigated by X-ray diffraction (XRD) and the microstructures were observed by scanning electron microscopy (SEM). It was found that the grains appeared smaller and the grain boundaries became more abundant when pressures were higher. We measured the electrical properties from room temperature to 723 K. Both the electrical resistivity and absolute value of Seebeck coefficient increase with the increasing synthetic pressure. At 723 K, the maximum power factor of [Formula: see text] was obtained for the sample synthesized under 3 GPa. The maximum ZT value of 0.61 was reached by [Formula: see text] synthesized under 3 GPa and measured at 723 K.

Sign in / Sign up

Export Citation Format

Share Document