Characterization of Lime: A Comparison and Scaling Down of the Coarse Grain Titration Test and the ASTM Slaking Rate Test

2009 ◽  
pp. 143-143-18 ◽  
Author(s):  
W. J. Schlitt ◽  
G. W. Healy
Keyword(s):  
Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 483
Author(s):  
Jing Wang ◽  
Riwei Xu ◽  
Chengzhong Wang ◽  
Jinping Xiong

We report on the preparation and characterization of a novel lamellar polypyrrole using an attapulgite–sulfur composite as a hard template. Pretreated attapulgite was utilized as the carrier of elemental sulfur and the attapulgite–sulfur–polypyrrole (AT @400 °C–S–PPy) composite with 50 wt.% sulfur was obtained. The structure and morphology of the composite were characterized with infrared spectroscopy (IR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). An AT @400 °C–S–PPy composite was further utilized as the cathode material for lithium–sulfur batteries. The first discharge specific capacity of this kind of battery reached 1175 mAh/g at a 0.1 C current rate and remained at 518 mAh/g after 100 cycles with capacity retention close to 44%. In the rate test, compared with the polypyrrole–sulfur (PPy–S) cathode material, the AT @400 °C–S–PPy cathode material showed lower capacity at a high current density, but it showed higher capacity when the current came back to a low current density, which was attributed to the “recycling” of pores and channels of attapulgite. Therefore, the lamellar composite with special pore structure has great value in improving the performance of lithium–sulfur batteries.


2013 ◽  
Vol 753 ◽  
pp. 231-234 ◽  
Author(s):  
Ning Wang ◽  
Yan Jun Li ◽  
Knut Marthinsen

In the present work an Al-Mn-(Fe-Si) model alloy has been subjected to different homogenization treatments, to achieve materials with different microchemistry states in terms of constituents, levels of Mn in solid solution (potential for concurrent precipitation) and dispersoid densities, followed by cold rolling and back-annealing. Characterization of the microchemistry state after homogenization and the evolution in dispersoid precipitation and its effects on the softening behavior after deformation has been performed. It is demonstrated that variations in microchemistry may have dramatic effects on the softening kinetics and the final grain structures, where both pre-existing fine and dense dispersoids before back annealing as well as precipitation concurrent with recovery and recrystallization strongly retard kinetics and generally lead to a coarse grain structure, while conditions with no or limited concurrent precipitation softens much faster and generally results in an even, fine and equi-axed grain structure. The different softening behaviors have been discussed in terms of Zener drag effects derived from the dispersoid evolutions.


2021 ◽  
Vol 23 (07) ◽  
pp. 329-341
Author(s):  
Ritesh Bathe ◽  
◽  
Audumbar Mali ◽  
Sagar Kale ◽  
Jitendra Pande ◽  
...  

Tramadol which is an opioid analgesic used to treat moderate to moderately severe pain act primarily by binding to the μ-opioid receptor and secondly by inhibiting the reactivity of norepinephrine and serotonin. The emulsion solvent evaporation method was used to encapsulate the polymers EC, HPMC K4M, and CAP, and characterization of formulations was performed. The microspheres obtained were white and spherical. The in vitro studies of the microspheres was performed using phosphate buffer of pH 6.8 at a temperature of 37 degrees Celsius and 100 rpm in 900ml USP basket type dissolution rate test apparatus for 8 hours and various parameters of the formulation were evaluated. Formulation F6 exhibited a higher yield and formulation of F3 entrapped maximum drug. The effect of the nature of polymer and polymer content was clearly visible on the drug release. The controlled release of the drug from the tramadol hydrochloride microsphere provides enhanced plasma drug content and higher bioavailability.


Author(s):  
ARIF BUDIMAN ◽  
IYAN SOPYAN ◽  
DENIA SEPTY RIYANDI

Objective: The aim of this study was to investigate the effects of changing in the proportions of the solid dispersion formula on the dissolution rate of glibenclamide. Methods: Solid dispersions were prepared by solvent evaporation method by using methanol as solvent, hydroxypropyl methylcellulose (HPMC) and polyvinyl pyrrolidone (PVP) as polymers. The prepared product was evaluated by the saturated solubility test and the dissolution rate test. The prepared product was characterized by Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and powder X-ray diffraction (PXRD) and Scanning Electron Microscopy (SEM). Results: The result showed solid dispersion with a ratio of glibenclamide: PVP: HPMC (1: 3: 6) has the highest increase in solubility (20 fold) compared to pure glibenclamide. This formula also showed an improvement in dissolution rate from 19.9±1.19% (pure glibenclamide) to 99±1.60% in 60 min. Characterization of FT-IR showed that no chemical reaction occurred in solid dispersion of glibenclamide. The results of X-ray diffraction analysis showed an amorphous form in all solid dispersion formulas. The results of DSC analysis showed that endothermic peak melting point of solid dispersion occurred, and the morphology of solid dispersion was more irregular than pure glibenclamide based on SEM characterization Conclusion: The solid dispersion of glibenclamide using PVP: HPMC as carriers can increase the solubility and dissolution rate compared to pure glibenclamide.


2021 ◽  
Vol 2015 (1) ◽  
pp. 012072
Author(s):  
Irina Koryakina ◽  
S Bikmetova ◽  
K Arabuli ◽  
A Evstrapov ◽  
A Pushkarev ◽  
...  

Abstract Conventional chemical synthesis methods for nanomaterials fabrication do not always provide precise reproducible synthesis with controllable physicochemical parameters. A better control over the resultant properties of nanomaterials can be achieved by scaling down the synthesis approach to the microlevel. This can be realized by means of microfluidics. In this work, a microfluidic approach is applied for the controllable synthesis of perovskite particles with defined cubic morphology. The structural characterization of perovskite particles is performed using scanning electron microscopy and X-ray diffraction. All the synthesized particles demonstrate photoluminescence.


Author(s):  
Mark M. Plecnik ◽  
Ronald S. Fearing

This study presents new results on a method to solve large kinematic synthesis systems termed Finite Root Generation. The method reduces the number of startpoints used in homotopy continuation to find all the roots of a kinematic synthesis system. For a single execution, many start systems are generated with corresponding startpoints using a random process such that start-points only track to finite roots. Current methods are burdened by computations of roots to infinity. New results include a characterization of scaling for different problem sizes, a technique for scaling down problems using cognate symmetries, and an application for the design of a spined pinch gripper mechanism. We show that the expected number of iterations to perform increases approximately linearly with the quantity of finite roots for a given synthesis problem. An implementation that effectively scales the four-bar path synthesis problem by six using its cognate structure found 100% of roots in an average of 16,546 iterations over ten executions. This marks a roughly six-fold improvement over the basic implementation of the algorithm.


Author(s):  
Kenneth J. King ◽  
John C. Estill ◽  
Rau´l B. Rebak

In its current design, the high-level nuclear waste container includes an external layer of Alloy 22 (Ni-22Cr-13Mo-3W-3Fe). Since the containers may be exposed to multi-ionic aqueous environments over their lifetime, a potential degradation mode of the outer layer could be environmentally assisted cracking (EAC). The objective of the current research is to characterize the effect of applied potential and temperature on the susceptibility of Alloy 22 to EAC in simulated concentrated water (SCW) using the slow strain rate test (SSRT). Results show that Alloy 22 may suffer EAC at applied potentials approximately 400 mV more anodic than the corrosion potential (Ecorr).


2020 ◽  
Author(s):  
Alexander Jussupow ◽  
Ana C. Messias ◽  
Ralf Stehle ◽  
Arie Geerlof ◽  
Sara M. Ø. Solbak ◽  
...  

AbstractPoly-ubiquitin chains are flexible multidomain proteins, whose conformational dynamics enable their molecular recognition by a large number of partners in multiple biological pathways. By using alternative linkage, it is possible to obtain poly-ubiquitin molecules with different dynamical properties. This flexibility is further increased by the possibility to tune the length of poly-ubiquitin chains. Characterizing the dynamics of poly-ubiquitins as a function of their length is thus relevant to understand their biology. Structural characterization of poly-ubiquitin conformational dynamics is challenging both experimentally and computationally due to increasing system size and conformational variability. Here, by developing highly efficient and accurate small-angle X-ray scattering driven Martini coarse-grain simulations, we characterize the dynamics of linear M1-linked di-, tri- and tetra-ubiquitin chains. Our data show that the behavior of the di-ubiquitin subunits is independent of the presence of additional ubiquitin modules. We propose that the conformational space sampled by linear poly-ubiquitins, in general, may follow a simple self-avoiding polymer model. These results, combined with experimental data from small angle X-ray scattering, biophysical techniques and additional simulations show that binding of NEMO, a central regulator in the NF-κB pathway, to linear poly-ubiquitin obeys a 2:1 (NEMO:poly-ubiquitin) stoichiometry in solution, even in the context of four ubiquitin units. Eventually, we show how the conformational properties of long poly-ubiquitins may modulate the binding with their partners in a length-dependent manner.SignificanceProtein conformational dynamics plays an essential role in molecular recognition mechanisms. The characterization of conformational dynamics is hampered by the conformational averaging of observable in experimental structural biology techniques and by the limitations in the accuracy of computational methods. By developing an efficient and accurate approach to combine small-angle X-ray scattering solution experiments and coarse-grain Martini simulations, we show that the conformational dynamics of linear poly-ubiquitins can be efficiently determined and to rationalize the role of poly-ubiquitin dynamic in the molecular recognition of the UBAN domain upon binding to the signaling regulator NEMO. The analysis of the conformational ensembles allows us to propose a general model of the dynamics of linear poly-ubiquitin chains where they can be described as a self-avoiding polymer with a characteristic length associated with their specific linkage.


2015 ◽  
Vol 17 (2) ◽  
pp. 1390-1398 ◽  
Author(s):  
Aiswarya B. Pawar ◽  
Sneha A. Deshpande ◽  
Srinivasa M. Gopal ◽  
Tsjerk A. Wassenaar ◽  
Chaitanya A. Athale ◽  
...  

The transient dimerization of transmembrane proteins is an important event in several cellular processes and here we use coarse-grain and meso-scale modeling methods to quantify their underlying dynamics.


Sign in / Sign up

Export Citation Format

Share Document